SuperSlicer/resources/profiles/PrusaResearch.ini

# Print profiles for the Prusa Research printers.

[vendor]
# Vendor name will be shown by the Config Wizard.
name = Prusa Research
# Configuration version of this file. Config file will only be installed, if the config_version differs.
# This means, the server may force the Slic3r configuration to be downgraded.
config_version = 0.3.2
# Where to get the updates from?
config_update_url = https://raw.githubusercontent.com/prusa3d/Slic3r-settings/master/live/PrusaResearch/

# The printer models will be shown by the Configuration Wizard in this order,
# also the first model installed & the first nozzle installed will be activated after install.
#TODO: One day we may differentiate variants of the nozzles / hot ends,
#for example by the melt zone size, or whether the nozzle is hardened.
# Printer model name will be shown by the installation wizard.

[printer_model:MK3]
name = Original Prusa i3 MK3
variants = 0.4; 0.25; 0.6

[printer_model:MK2.5]
name = Original Prusa i3 MK2.5
variants = 0.4; 0.25; 0.6

[printer_model:MK2S]
name = Original Prusa i3 MK2/S
variants = 0.4; 0.25; 0.6

[printer_model:MK3MMU2]
name = Original Prusa i3 MK3 MMU 2.0
variants = 0.4

[printer_model:MK2SMM]
name = Original Prusa i3 MK2/S MMU 1.0
variants = 0.4; 0.6

[printer_model:MK2.5MMU2]
name = Original Prusa i3 MK2.5 MMU 2.0
variants = 0.4

# All presets starting with asterisk, for example *common*, are intermediate and they will
# not make it into the user interface.

# Common print preset, mostly derived from MK2 single material with a 0.4mm nozzle.
# All other print presets will derive from the *common* print preset.
[print:*common*]
avoid_crossing_perimeters = 0
bridge_acceleration = 1000
bridge_angle = 0
bridge_flow_ratio = 0.8
over_bridge_flow_ratio = 1.2
bridge_speed = 20
brim_width = 0
clip_multipart_objects = 1
compatible_printers = 
complete_objects = 0
default_acceleration = 1000
dont_support_bridges = 1
elefant_foot_compensation = 0
ensure_vertical_shell_thickness = 1
top_fill_pattern = rectilinear
bottom_fill_pattern = rectilinear
external_perimeters_first = 0
external_perimeter_extrusion_width = 0.45
extra_perimeters = 0
only_one_perimeter_top = 0
extruder_clearance_height = 20
extruder_clearance_radius = 20
extrusion_width = 0.45
fill_angle = 45
fill_density = 20%
fill_pattern = cubic
first_layer_acceleration = 1000
first_layer_extrusion_width = 0.42
first_layer_height = 0.2
first_layer_speed = 20
gap_fill_speed = 40
gcode_comments = 0
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0.45
infill_first = 0
infill_only_where_needed = 0
infill_overlap = 25%
interface_shells = 0
max_print_speed = 100
max_volumetric_extrusion_rate_slope_negative = 0
max_volumetric_extrusion_rate_slope_positive = 0
max_volumetric_speed = 0
min_skirt_length = 4
notes = 
overhangs = 0
only_retract_when_crossing_perimeters = 0
ooze_prevention = 0
output_filename_format = {input_filename_base}_{layer_height}mm_{filament_type[0]}_{printer_model}.gcode
perimeters = 2
perimeter_extruder = 1
perimeter_extrusion_width = 0.45
post_process = 
print_settings_id = 
raft_layers = 0
resolution = 0
seam_position = nearest
single_extruder_multi_material_priming = 1
skirts = 1
skirt_distance = 2
skirt_height = 3
small_perimeter_speed = 25
solid_infill_below_area = 0
solid_infill_every_layers = 0
solid_infill_extruder = 1
solid_infill_extrusion_width = 0.45
spiral_vase = 0
standby_temperature_delta = -5
support_material = 0
support_material_extruder = 0
support_material_extrusion_width = 0.35
support_material_interface_extruder = 0
support_material_angle = 0
support_material_buildplate_only = 0
support_material_enforce_layers = 0
support_material_contact_distance = 0.1
support_material_interface_contact_loops = 0
support_material_interface_layers = 2
support_material_interface_spacing = 0.2
support_material_interface_speed = 100%
support_material_pattern = rectilinear
support_material_spacing = 2
support_material_speed = 50
support_material_synchronize_layers = 0
support_material_threshold = 55
support_material_with_sheath = 0
support_material_xy_spacing = 50%
thin_walls = 0
top_infill_extrusion_width = 0.45
top_solid_infill_speed = 40
travel_speed = 180
wipe_tower = 1
wipe_tower_bridging = 10
wipe_tower_rotation_angle = 0
wipe_tower_width = 60
wipe_tower_x = 170
wipe_tower_y = 140
xy_size_compensation = 0

[print:*MK3*]
fill_pattern = grid
single_extruder_multi_material_priming = 0
wipe_tower_x = 170
wipe_tower_y = 125

# Print parameters common to a 0.25mm diameter nozzle.
[print:*0.25nozzle*]
external_perimeter_extrusion_width = 0.25
extrusion_width = 0.25
first_layer_extrusion_width = 0.25
infill_extrusion_width = 0.25
perimeter_extrusion_width = 0.25
solid_infill_extrusion_width = 0.25
top_infill_extrusion_width = 0.25
support_material_extrusion_width = 0.2
support_material_interface_layers = 0
support_material_interface_spacing = 0.15
support_material_spacing = 1
support_material_xy_spacing = 150%

# Print parameters common to a 0.6mm diameter nozzle.
[print:*0.6nozzle*]
external_perimeter_extrusion_width = 0.61
extrusion_width = 0.67
first_layer_extrusion_width = 0.65
infill_extrusion_width = 0.7
perimeter_extrusion_width = 0.65
solid_infill_extrusion_width = 0.65
top_infill_extrusion_width = 0.6
support_material_extrusion_width = 0.55

[print:*soluble_support*]
overhangs = 1
skirts = 0
support_material = 1
support_material_contact_distance = 0
support_material_extruder = 4
support_material_extrusion_width = 0.45
support_material_interface_extruder = 4
support_material_interface_spacing = 0.1
support_material_synchronize_layers = 1
support_material_threshold = 80
support_material_with_sheath = 1

# XXXXXXXXXXXXXXXXXXXX
# XXX--- 0.05mm ---XXX
# XXXXXXXXXXXXXXXXXXXX

[print:*0.05mm*]
inherits = *common*
bottom_solid_layers = 10
bridge_acceleration = 300
bridge_flow_ratio = 0.7
default_acceleration = 500
external_perimeter_speed = 20
fill_density = 20%
first_layer_acceleration = 500
gap_fill_speed = 20
infill_acceleration = 800
infill_speed = 30
max_print_speed = 80
small_perimeter_speed = 20
solid_infill_speed = 30
support_material_extrusion_width = 0.3
support_material_spacing = 1.5
layer_height = 0.05
perimeter_acceleration = 300
perimeter_speed = 30
perimeters = 3
support_material_speed = 30
top_solid_infill_speed = 20
top_solid_layers = 15

[print:0.05mm ULTRADETAIL]
inherits = *0.05mm*
compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK2.*/ and nozzle_diameter[0]==0.4 and num_extruders==1
infill_extrusion_width = 0.5

[print:0.05mm ULTRADETAIL MK3]
inherits = *0.05mm*; *MK3*
compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK3.*/  and nozzle_diameter[0]==0.4 and ! single_extruder_multi_material
top_infill_extrusion_width = 0.4

[print:0.05mm ULTRADETAIL 0.25 nozzle]
inherits = *0.05mm*; *0.25nozzle*
compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK2.*/ and nozzle_diameter[0]==0.25 and num_extruders==1
fill_density = 20%
infill_speed = 20
max_print_speed = 100
perimeter_speed = 20
small_perimeter_speed = 15
solid_infill_speed = 20
support_material_speed = 20

[print:0.05mm ULTRADETAIL 0.25 nozzle MK3]
inherits = *0.05mm*; *0.25nozzle*; *MK3*
compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK3.*/ and nozzle_diameter[0]==0.25 and num_extruders==1

# XXXXXXXXXXXXXXXXXXXX
# XXX--- 0.10mm ---XXX
# XXXXXXXXXXXXXXXXXXXX

[print:*0.10mm*]
inherits = *common*
bottom_solid_layers = 7
bridge_flow_ratio = 0.7
compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK2.*/ and nozzle_diameter[0]==0.4 and num_extruders==1
layer_height = 0.1
perimeter_acceleration = 800
top_solid_layers = 9

[print:0.10mm DETAIL]
inherits = *0.10mm*
compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK2.*/ and nozzle_diameter[0]==0.4 and num_extruders==1
external_perimeter_speed = 40
infill_acceleration = 2000
infill_speed = 60
perimeter_speed = 50
solid_infill_speed = 50

[print:0.10mm DETAIL MK3]
inherits = *0.10mm*; *MK3*
bridge_speed = 30
compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK3.*/ and nozzle_diameter[0]==0.4 and ! single_extruder_multi_material
external_perimeter_speed = 35
infill_acceleration = 1250
infill_speed = 200
max_print_speed = 200
perimeter_speed = 45
solid_infill_speed = 200
top_infill_extrusion_width = 0.4
top_solid_infill_speed = 50

[print:0.10mm DETAIL 0.25 nozzle]
inherits = *0.10mm*; *0.25nozzle*
bridge_acceleration = 600
compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK2.*/ and nozzle_diameter[0]==0.25
external_perimeter_speed = 20
infill_acceleration = 1600
infill_speed = 40
perimeter_acceleration = 600
perimeter_speed = 25
small_perimeter_speed = 15
solid_infill_speed = 40
top_solid_infill_speed = 30

[print:0.10mm DETAIL 0.25 nozzle MK3]
inherits = *0.10mm*; *0.25nozzle*; *MK3*
bridge_speed = 30
compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK3.*/ and nozzle_diameter[0]==0.25
external_perimeter_speed = 35
infill_acceleration = 1250
infill_speed = 200
max_print_speed = 200
perimeter_speed = 45
solid_infill_speed = 200
top_solid_infill_speed = 50

[print:0.10mm DETAIL 0.6 nozzle MK3]
inherits = *0.10mm*; *0.6nozzle*; *MK3*
bridge_speed = 30
compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK3.*/ and nozzle_diameter[0]==0.6
external_perimeter_speed = 35
infill_acceleration = 1250
infill_speed = 200
max_print_speed = 200
perimeter_speed = 45
solid_infill_speed = 200
top_solid_infill_speed = 50

# XXXXXXXXXXXXXXXXXXXX
# XXX--- 0.15mm ---XXX
# XXXXXXXXXXXXXXXXXXXX

[print:*0.15mm*]
inherits = *common*
bottom_solid_layers = 5
external_perimeter_speed = 40
infill_acceleration = 2000
infill_speed = 60
layer_height = 0.15
perimeter_acceleration = 800
perimeter_speed = 50
solid_infill_speed = 50
top_infill_extrusion_width = 0.4
top_solid_layers = 7

[print:0.15mm 100mms Linear Advance]
inherits = *0.15mm*
bridge_flow_ratio = 0.95
compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK2[^\.].*/ and nozzle_diameter[0]==0.4
external_perimeter_speed = 50
infill_speed = 100
max_print_speed = 150
perimeter_speed = 60
small_perimeter_speed = 30
solid_infill_speed = 100
support_material_speed = 60
top_solid_infill_speed = 70

[print:0.15mm OPTIMAL]
inherits = *0.15mm*
compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK2[^\.].*/ and nozzle_diameter[0]==0.4
top_infill_extrusion_width = 0.45

[print:0.15mm OPTIMAL 0.25 nozzle]
inherits = *0.15mm*; *0.25nozzle*
bridge_acceleration = 600
bridge_flow_ratio = 0.7
compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK2.*/ and nozzle_diameter[0]==0.25
external_perimeter_speed = 20
infill_acceleration = 1600
infill_speed = 40
perimeter_acceleration = 600
perimeter_speed = 25
small_perimeter_speed = 15
solid_infill_speed = 40
top_solid_infill_speed = 30

[print:0.15mm OPTIMAL 0.6 nozzle]
inherits = *0.15mm*; *0.6nozzle*
compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK2.*/ and nozzle_diameter[0]==0.6

[print:0.15mm OPTIMAL MK3]
inherits = *0.15mm*; *MK3*
bridge_speed = 30
compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK3.*/ and nozzle_diameter[0]==0.4
external_perimeter_speed = 35
infill_acceleration = 1250
infill_speed = 200
max_print_speed = 200
perimeter_speed = 45
solid_infill_speed = 200
top_solid_infill_speed = 50

[print:0.15mm OPTIMAL MK3 SOLUBLE FULL]
inherits = 0.15mm OPTIMAL MK3; *soluble_support*
compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK3.*/ and nozzle_diameter[0]==0.4 and num_extruders>1
notes = Set your solluble extruder in Multiple Extruders > Support material/raft/skirt extruder &  Support material/raft interface extruder
support_material_extruder = 5
support_material_interface_extruder = 5
perimeter_speed = 40
solid_infill_speed = 40
top_infill_extrusion_width = 0.45
top_solid_infill_speed = 30

[print:0.15mm OPTIMAL MK3 SOLUBLE INTERFACE]
inherits = 0.15mm OPTIMAL MK3 SOLUBLE FULL
notes = Set your solluble extruder in Multiple Extruders >  Support material/raft interface extruder
support_material_extruder = 0
support_material_interface_layers = 3
support_material_with_sheath = 0

[print:0.15mm OPTIMAL SOLUBLE FULL]
inherits = *0.15mm*; *soluble_support*
compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK2[^\.].*/ and nozzle_diameter[0]==0.4 and num_extruders>1
external_perimeter_speed = 25
notes = Set your solluble extruder in Multiple Extruders > Support material/raft/skirt extruder &  Support material/raft interface extruder
perimeter_speed = 40
solid_infill_speed = 40
top_infill_extrusion_width = 0.45
top_solid_infill_speed = 30

[print:0.15mm OPTIMAL SOLUBLE INTERFACE]
inherits = 0.15mm OPTIMAL SOLUBLE FULL
notes = Set your solluble extruder in Multiple Extruders >  Support material/raft interface extruder
support_material_extruder = 0
support_material_interface_layers = 3
support_material_with_sheath = 0
support_material_xy_spacing = 80%

[print:0.15mm OPTIMAL 0.25 nozzle MK3]
inherits = *0.15mm*; *0.25nozzle*; *MK3*
bridge_speed = 30
compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK3.*/ and nozzle_diameter[0]==0.25
external_perimeter_speed = 35
infill_acceleration = 1250
infill_speed = 200
max_print_speed = 200
perimeter_speed = 45
solid_infill_speed = 200
top_solid_infill_speed = 50

[print:*0.20mm*]
inherits = *common*
bottom_solid_layers = 4
bridge_flow_ratio = 0.95
external_perimeter_speed = 40
infill_acceleration = 1250
infill_speed = 60
layer_height = 0.2
perimeter_acceleration = 800
perimeter_speed = 50
solid_infill_speed = 50
top_infill_extrusion_width = 0.4
top_solid_layers = 5

[print:0.15mm OPTIMAL 0.6 nozzle MK3]
inherits = *0.15mm*; *0.6nozzle*; *MK3*
bridge_speed = 30
compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK3.*/ and nozzle_diameter[0]==0.6
external_perimeter_speed = 35
infill_acceleration = 1250
infill_speed = 200
max_print_speed = 200
perimeter_speed = 45
solid_infill_speed = 200
top_solid_infill_speed = 50

# XXXXXXXXXXXXXXXXXXXX
# XXX--- 0.20mm ---XXX
# XXXXXXXXXXXXXXXXXXXX

[print:0.20mm 100mms Linear Advance]
inherits = *0.20mm*
compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK2[^\.].*/ and nozzle_diameter[0]==0.4
external_perimeter_speed = 50
infill_speed = 100
max_print_speed = 150
perimeter_speed = 60
small_perimeter_speed = 30
solid_infill_speed = 100
support_material_speed = 60
top_solid_infill_speed = 70

[print:0.20mm FAST MK3]
inherits = *0.20mm*; *MK3*
bridge_speed = 30
compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK3.*/ and nozzle_diameter[0]==0.4
external_perimeter_speed = 35
infill_acceleration = 1250
infill_speed = 200
max_print_speed = 200
perimeter_speed = 45
solid_infill_speed = 200
top_solid_infill_speed = 50

[print:0.20mm FAST MK3 SOLUBLE FULL]
inherits = 0.20mm FAST MK3; *soluble_support*
compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK3.*/ and nozzle_diameter[0]==0.4 and num_extruders>1
notes = Set your solluble extruder in Multiple Extruders > Support material/raft/skirt extruder &  Support material/raft interface extruder
support_material_extruder = 5
support_material_interface_extruder = 5
perimeter_speed = 40
solid_infill_speed = 40
top_infill_extrusion_width = 0.45
top_solid_infill_speed = 30

[print:0.20mm FAST MK3 SOLUBLE INTERFACE]
inherits = 0.20mm FAST MK3 SOLUBLE FULL
notes = Set your solluble extruder in Multiple Extruders >  Support material/raft interface extruder
support_material_extruder = 0
support_material_interface_layers = 3
support_material_with_sheath = 0

[print:0.20mm NORMAL]
inherits = *0.20mm*
compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK2[^\.].*/ and nozzle_diameter[0]==0.4

[print:0.20mm NORMAL 0.6 nozzle]
inherits = *0.20mm*; *0.6nozzle*
compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK2.*/ and nozzle_diameter[0]==0.6

[print:0.20mm NORMAL SOLUBLE FULL]
inherits = *0.20mm*; *soluble_support*
compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK2[^\.].*/ and nozzle_diameter[0]==0.4 and num_extruders>1
external_perimeter_speed = 30
notes = Set your solluble extruder in Multiple Extruders > Support material/raft/skirt extruder &  Support material/raft interface extruder
perimeter_speed = 40
solid_infill_speed = 40
top_solid_infill_speed = 30

[print:0.20mm NORMAL SOLUBLE INTERFACE]
inherits = 0.20mm NORMAL SOLUBLE FULL
notes = Set your solluble extruder in Multiple Extruders >  Support material/raft interface extruder
support_material_extruder = 0
support_material_interface_layers = 3
support_material_with_sheath = 0
support_material_xy_spacing = 80%

[print:0.20mm FAST 0.6 nozzle MK3]
inherits = *0.20mm*; *0.6nozzle*; *MK3*
bridge_speed = 30
compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK3.*/ and nozzle_diameter[0]==0.6
external_perimeter_speed = 35
infill_acceleration = 1250
infill_speed = 200
max_print_speed = 200
perimeter_speed = 45
solid_infill_speed = 200
top_solid_infill_speed = 50

# XXXXXXXXXXXXXXXXXXXX
# XXX--- 0.35mm ---XXX
# XXXXXXXXXXXXXXXXXXXX

[print:*0.35mm*]
inherits = *common*
bottom_solid_layers = 3
external_perimeter_extrusion_width = 0.6
external_perimeter_speed = 40
first_layer_extrusion_width = 0.75
infill_acceleration = 2000
infill_speed = 60
layer_height = 0.35
perimeter_acceleration = 800
perimeter_extrusion_width = 0.65
perimeter_speed = 50
solid_infill_extrusion_width = 0.65
solid_infill_speed = 60
top_solid_infill_speed = 50
top_solid_layers = 4

[print:0.35mm FAST]
inherits = *0.35mm*
bridge_flow_ratio = 0.95
compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK2[^\.].*/ and nozzle_diameter[0]==0.4
first_layer_extrusion_width = 0.42
perimeter_extrusion_width = 0.43
solid_infill_extrusion_width = 0.7
top_infill_extrusion_width = 0.43

[print:0.35mm FAST 0.6 nozzle]
inherits = *0.35mm*; *0.6nozzle*
compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK2.*/ and nozzle_diameter[0]==0.6

[print:0.35mm FAST sol full 0.6 nozzle]
inherits = *0.35mm*; *0.6nozzle*; *soluble_support*
compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK2.*/ and nozzle_diameter[0]==0.6 and num_extruders>1
external_perimeter_extrusion_width = 0.6
external_perimeter_speed = 30
notes = Set your solluble extruder in Multiple Extruders >  Support material/raft interface extruder
perimeter_speed = 40
support_material_interface_layers = 3
support_material_xy_spacing = 120%
top_infill_extrusion_width = 0.57

[print:0.35mm FAST sol int 0.6 nozzle]
inherits = 0.35mm FAST sol full 0.6 nozzle
support_material_extruder = 0
support_material_interface_layers = 2
support_material_with_sheath = 0
support_material_xy_spacing = 150%

# XXXXXXXXXXXXXXXXXXXXXX
# XXX----- MK2.5 ----XXX
# XXXXXXXXXXXXXXXXXXXXXX

[print:0.15mm 100mms Linear Advance MK2.5]
inherits = 0.15mm 100mms Linear Advance
compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK2.5.*/ and nozzle_diameter[0]==0.4
single_extruder_multi_material_priming = 0

[print:0.15mm OPTIMAL MK2.5]
inherits = 0.15mm OPTIMAL
compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK2.5.*/ and nozzle_diameter[0]==0.4
single_extruder_multi_material_priming = 0

[print:0.15mm OPTIMAL SOLUBLE FULL MK2.5]
inherits = 0.15mm OPTIMAL SOLUBLE FULL
compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK2.5.*/ and nozzle_diameter[0]==0.4 and num_extruders>1

[print:0.15mm OPTIMAL SOLUBLE INTERFACE MK2.5]
inherits = 0.15mm OPTIMAL SOLUBLE INTERFACE
compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK2.5.*/ and nozzle_diameter[0]==0.4 and num_extruders>1

[print:0.20mm 100mms Linear Advance MK2.5]
inherits = 0.20mm 100mms Linear Advance
compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK2.5.*/ and nozzle_diameter[0]==0.4
single_extruder_multi_material_priming = 0

[print:0.20mm NORMAL MK2.5]
inherits = 0.20mm NORMAL
compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK2.5.*/ and nozzle_diameter[0]==0.4
single_extruder_multi_material_priming = 0

[print:0.20mm NORMAL SOLUBLE FULL MK2.5]
inherits = 0.20mm NORMAL SOLUBLE FULL
compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK2.5.*/ and nozzle_diameter[0]==0.4 and num_extruders>1
single_extruder_multi_material_priming = 0

[print:0.20mm NORMAL SOLUBLE INTERFACE MK2.5]
inherits = 0.20mm NORMAL SOLUBLE INTERFACE
compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK2.5.*/ and nozzle_diameter[0]==0.4 and num_extruders>1
single_extruder_multi_material_priming = 0

[print:0.35mm FAST MK2.5]
inherits = 0.35mm FAST
compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK2.5.*/ and nozzle_diameter[0]==0.4
single_extruder_multi_material_priming = 0

# XXXXXXxxXXXXXXXXXXXXXX
# XXX--- filament ---XXX
# XXXXXXXXxxXXXXXXXXXXXX

[filament:*common*]
cooling = 1
compatible_printers = 
# For now, all but selected filaments are disabled for the MMU 2.0
compatible_printers_condition = ! (printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK(2.5|3).*/ and single_extruder_multi_material)
end_filament_gcode = "; Filament-specific end gcode"
extrusion_multiplier = 1
filament_loading_speed = 28
filament_loading_speed_start = 3
filament_unloading_speed = 90
filament_unloading_speed_start = 100
filament_toolchange_delay = 0
filament_cooling_moves = 4
filament_cooling_initial_speed = 2.2
filament_cooling_final_speed = 3.4
filament_load_time = 0
filament_unload_time = 0
filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
filament_minimal_purge_on_wipe_tower = 15
filament_cost = 0
filament_density = 0
filament_diameter = 1.75
filament_notes = ""
filament_settings_id = ""
filament_soluble = 0
min_print_speed = 15
slowdown_below_layer_time = 20
start_filament_gcode = "M900 K{if printer_notes=~/.*PRINTER_HAS_BOWDEN.*/}200{else}30{endif}; Filament gcode"

[filament:*PLA*]
inherits = *common*
bed_temperature = 60
bridge_fan_speed = 100
disable_fan_first_layers = 1
fan_always_on = 1
fan_below_layer_time = 100
filament_colour = #FF3232
filament_max_volumetric_speed = 15
filament_type = PLA
first_layer_bed_temperature = 60
first_layer_temperature = 215
max_fan_speed = 100
min_fan_speed = 100
temperature = 210

[filament:*PET*]
inherits = *common*
bed_temperature = 90
bridge_fan_speed = 50
disable_fan_first_layers = 3
fan_always_on = 1
fan_below_layer_time = 20
filament_colour = #FF8000
filament_max_volumetric_speed = 8
filament_type = PET
first_layer_bed_temperature = 85
first_layer_temperature = 230
max_fan_speed = 50
min_fan_speed = 30
start_filament_gcode = "M900 K{if printer_notes=~/.*PRINTER_HAS_BOWDEN.*/}200{else}45{endif}; Filament gcode"
temperature = 240

[filament:*ABS*]
inherits = *common*
bed_temperature = 110
bridge_fan_speed = 30
cooling = 0
disable_fan_first_layers = 3
fan_always_on = 0
fan_below_layer_time = 20
filament_colour = #3A80CA
filament_max_volumetric_speed = 11
filament_ramming_parameters = "120 100 5.70968 6.03226 7 8.25806 9 9.19355 9.3871 9.77419 10.129 10.3226 10.4516 10.5161| 0.05 5.69677 0.45 6.15484 0.95 8.76774 1.45 9.20323 1.95 9.95806 2.45 10.3871 2.95 10.5677 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
filament_type = ABS
first_layer_bed_temperature = 100
first_layer_temperature = 255
max_fan_speed = 30
min_fan_speed = 20
temperature = 255

[filament:*FLEX*]
inherits = *common*
bed_temperature = 50
bridge_fan_speed = 100
# For now, all but selected filaments are disabled for the MMU 2.0
compatible_printers_condition = nozzle_diameter[0]>0.35 and num_extruders==1 && ! (printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK3.*/ and single_extruder_multi_material)
cooling = 0
disable_fan_first_layers = 1
extrusion_multiplier = 1.2
fan_always_on = 0
fan_below_layer_time = 100
filament_colour = #00CA0A
filament_max_volumetric_speed = 1.5
filament_type = FLEX
first_layer_bed_temperature = 50
first_layer_temperature = 240
max_fan_speed = 90
min_fan_speed = 70
start_filament_gcode = "M900 K{if printer_notes=~/.*PRINTER_HAS_BOWDEN.*/}200{else}10{endif}; Filament gcode"
temperature = 240

[filament:ColorFabb Brass Bronze]
inherits = *PLA*
# For now, all but selected filaments are disabled for the MMU 2.0
compatible_printers_condition = nozzle_diameter[0]>0.35 and ! (printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK(2.5|3).*/ and single_extruder_multi_material)
extrusion_multiplier = 1.2
filament_cost = 80.65
filament_density = 4
filament_colour = #804040
filament_max_volumetric_speed = 10

[filament:ColorFabb HT]
inherits = *PET*
bed_temperature = 110
bridge_fan_speed = 30
cooling = 1
disable_fan_first_layers = 3
fan_always_on = 0
fan_below_layer_time = 10
filament_cost = 58.66
filament_density = 1.18
first_layer_bed_temperature = 105
first_layer_temperature = 270
max_fan_speed = 20
min_fan_speed = 10
start_filament_gcode = "M900 K{if printer_notes=~/.*PRINTER_HAS_BOWDEN.*/}200{else}45{endif}; Filament gcode"
temperature = 270

[filament:ColorFabb PLA-PHA]
inherits = *PLA*
filament_cost = 55.5
filament_density = 1.24

[filament:ColorFabb Woodfil]
inherits = *PLA*
# For now, all but selected filaments are disabled for the MMU 2.0
compatible_printers_condition = nozzle_diameter[0]>0.35 and ! (printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK(2.5|3).*/ and single_extruder_multi_material)
extrusion_multiplier = 1.2
filament_cost = 62.9
filament_density = 1.15
filament_colour = #804040
filament_max_volumetric_speed = 10
first_layer_temperature = 200
start_filament_gcode = "M900 K{if printer_notes=~/.*PRINTER_HAS_BOWDEN.*/}200{else}10{endif}; Filament gcode"
temperature = 200

[filament:ColorFabb XT]
inherits = *PET*
filament_type = PET
filament_cost = 62.9
filament_density = 1.27
first_layer_bed_temperature = 90
first_layer_temperature = 260
temperature = 270

[filament:ColorFabb XT-CF20]
inherits = *PET*
extrusion_multiplier = 1.2
filament_cost = 80.65
filament_density = 1.35
filament_colour = #804040
filament_max_volumetric_speed = 1
first_layer_bed_temperature = 90
first_layer_temperature = 260
start_filament_gcode = "M900 K{if printer_notes=~/.*PRINTER_HAS_BOWDEN.*/}200{else}30{endif}; Filament gcode"
temperature = 260

[filament:ColorFabb nGen]
inherits = *PET*
filament_cost = 21.2
filament_density = 1.2
bridge_fan_speed = 40
fan_always_on = 0
fan_below_layer_time = 10
filament_type = NGEN
first_layer_temperature = 240
max_fan_speed = 35
min_fan_speed = 20

[filament:ColorFabb nGen flex]
inherits = *FLEX*
filament_cost = 0
filament_density = 1
bed_temperature = 85
bridge_fan_speed = 40
cooling = 1
disable_fan_first_layers = 3
extrusion_multiplier = 1
fan_below_layer_time = 10
filament_max_volumetric_speed = 5
first_layer_bed_temperature = 85
first_layer_temperature = 260
max_fan_speed = 35
min_fan_speed = 20
temperature = 260

[filament:E3D Edge]
inherits = *PET*
filament_cost = 56.9
filament_density = 1.26
filament_notes = "List of manufacturers tested with standart PET print settings for MK2:\n\nE3D Edge\nFillamentum CPE GH100\nPlasty Mladeč PETG"

[filament:E3D PC-ABS]
inherits = *ABS*
filament_cost = 0
filament_density = 1.05
first_layer_temperature = 270
temperature = 270

[filament:Fillamentum ABS]
inherits = *ABS*
filament_cost = 32.4
filament_density = 1.04
first_layer_temperature = 240
temperature = 240

[filament:Fillamentum ASA]
inherits = *ABS*
filament_cost = 38.7
filament_density = 1.04
fan_always_on = 1
first_layer_temperature = 265
temperature = 265

[filament:Fillamentum CPE HG100 HM100]
inherits = *PET*
filament_cost = 54.1
filament_density = 1.25
filament_notes = "CPE HG100 , CPE HM100"
first_layer_bed_temperature = 90
first_layer_temperature = 275
max_fan_speed = 50
min_fan_speed = 50
temperature = 275

[filament:Fillamentum Timberfil]
inherits = *PLA*
# For now, all but selected filaments are disabled for the MMU 2.0
compatible_printers_condition = nozzle_diameter[0]>0.35 and ! (printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK(2.5|3).*/ and single_extruder_multi_material)
extrusion_multiplier = 1.2
filament_cost = 68
filament_density = 1.15
filament_colour = #804040
filament_max_volumetric_speed = 10
first_layer_temperature = 190
start_filament_gcode = "M900 K{if printer_notes=~/.*PRINTER_HAS_BOWDEN.*/}200{else}10{endif}; Filament gcode"
temperature = 190

[filament:Generic ABS]
inherits = *ABS*
filament_cost = 27.82
filament_density = 1.04
filament_notes = "List of materials tested with standart ABS print settings for MK2:\n\nEsun ABS\nFil-A-Gehr ABS\nHatchboxABS\nPlasty Mladeč ABS"

[filament:Generic PET]
inherits = *PET*
filament_cost = 27.82
filament_density = 1.24
filament_notes = "List of manufacturers tested with standart PET print settings for MK2:\n\nE3D Edge\nFillamentum CPE GH100\nPlasty Mladeč PETG"

[filament:Generic PLA]
inherits = *PLA*
filament_cost = 25.4
filament_density = 1.27
filament_notes = "List of materials tested with standart PLA print settings for MK2:\n\nDas Filament\nEsun PLA\nEUMAKERS PLA\nFiberlogy HD-PLA\nFillamentum PLA\nFloreon3D\nHatchbox PLA\nPlasty Mladeč PLA\nPrimavalue PLA\nProto pasta Matte Fiber\nVerbatim PLA\nVerbatim BVOH"

[filament:Polymaker PC-Max]
inherits = *ABS*
filament_cost = 77.3
filament_density = 1.20
bed_temperature = 115
filament_colour = #3A80CA
first_layer_bed_temperature = 100
first_layer_temperature = 270
temperature = 270

[filament:Primavalue PVA]
inherits = *PLA*
filament_cost = 108
filament_density = 1.23
cooling = 0
fan_always_on = 0
filament_colour = #FFFFD7
filament_max_volumetric_speed = 10
filament_notes = "List of materials tested with standart PVA print settings for MK2:\n\nPrimaSelect PVA+\nICE FILAMENTS PVA 'NAUGHTY NATURAL'\nVerbatim BVOH"
filament_ramming_parameters = "120 100 8.3871 8.6129 8.93548 9.22581 9.48387 9.70968 9.87097 10.0323 10.2258 10.4194 10.6452 10.8065| 0.05 8.34193 0.45 8.73548 0.95 9.34836 1.45 9.78385 1.95 10.0871 2.45 10.5161 2.95 10.8903 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
filament_soluble = 1
filament_type = PVA
first_layer_temperature = 195
start_filament_gcode = "M900 K{if printer_notes=~/.*PRINTER_HAS_BOWDEN.*/}200{else}10{endif}; Filament gcode"
temperature = 195

[filament:Prusa ABS]
inherits = *ABS*
filament_cost = 27.82
filament_density = 1.08
filament_notes = "List of materials tested with standart ABS print settings for MK2:\n\nEsun ABS\nFil-A-Gehr ABS\nHatchboxABS\nPlasty Mladeč ABS"

[filament:*ABS MMU2*]
inherits = Prusa ABS
compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK(2.5|3).*/ and single_extruder_multi_material
filament_cooling_final_speed = 50 
filament_cooling_initial_speed = 10
filament_cooling_moves = 5
filament_ramming_parameters = "120 110 5.32258 5.45161 5.67742 6 6.48387 7.12903 7.90323 8.70968 9.3871 9.83871 10.0968 10.2258| 0.05 5.30967 0.45 5.50967 0.95 6.1871 1.45 7.39677 1.95 9.05484 2.45 10 2.95 10.3098 3.45 13.0839 3.95 7.6 4.45 7.6 4.95 7.6";

[filament:Generic ABS MMU2]
inherits = *ABS MMU2*

[filament:Prusa ABS MMU2]
inherits = *ABS MMU2*

[filament:Prusa HIPS]
inherits = *ABS*
filament_cost = 27.3
filament_density = 1.04
bridge_fan_speed = 50
cooling = 1
extrusion_multiplier = 0.9
fan_always_on = 1
fan_below_layer_time = 10
filament_colour = #FFFFD7
filament_soluble = 1
filament_type = HIPS
first_layer_temperature = 220
max_fan_speed = 20
min_fan_speed = 20
start_filament_gcode = "M900 K{if printer_notes=~/.*PRINTER_HAS_BOWDEN.*/}200{else}10{endif}; Filament gcode"
temperature = 220

[filament:Prusa PET]
inherits = *PET*
filament_cost = 27.82
filament_density = 1.27
filament_notes = "List of manufacturers tested with standart PET print settings for MK2:\n\nE3D Edge\nFillamentum CPE GH100\nPlasty Mladeč PETG"

[filament:*PET MMU2*]
inherits = Prusa PET
compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK(2.5|3).*/ and single_extruder_multi_material
temperature = 230
first_layer_temperature = 230
filament_cooling_final_speed = 1
filament_cooling_initial_speed = 2
filament_cooling_moves = 1
filament_load_time = 12
filament_loading_speed = 14
filament_notes = PET
filament_ramming_parameters = "120 140 4.70968 4.74194 4.77419 4.80645 4.83871 4.87097 4.90323 5 5.25806 5.67742 6.29032 7.06452 7.83871 8.3871| 0.05 4.72901 0.45 4.73545 0.95 4.83226 1.45 4.88067 1.95 5.05483 2.45 5.93553 2.95 7.53556 3.45 8.6323 3.95 7.6 4.45 7.6 4.95 7.6"
filament_unload_time = 11
filament_unloading_speed = 20
filament_unloading_speed_start = 120

[filament:Generic PET MMU2]
inherits = *PET MMU2*

[filament:Prusa PET MMU2]
inherits = *PET MMU2*

[filament:Prusa PLA]
inherits = *PLA*
filament_cost = 25.4
filament_density = 1.24
filament_notes = "List of materials tested with standart PLA print settings for MK2:\n\nDas Filament\nEsun PLA\nEUMAKERS PLA\nFiberlogy HD-PLA\nFillamentum PLA\nFloreon3D\nHatchbox PLA\nPlasty Mladeč PLA\nPrimavalue PLA\nProto pasta Matte Fiber\nVerbatim PLA\nVerbatim BVOH"

[filament:Prusament PLA]
inherits = *PLA*
temperature = 215
filament_cost = 24.99
filament_density = 1.24
filament_notes = "Affordable filament for everyday printing in premium quality manufactured in-house by Josef Prusa"

[filament:*PLA MMU2*]
inherits = Prusa PLA
compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK(2.5|3).*/ and single_extruder_multi_material
temperature = 205
filament_cooling_final_speed = 1
filament_cooling_initial_speed = 2
filament_cooling_moves = 1
filament_load_time = 12
filament_loading_speed = 14
filament_ramming_parameters = "120 110 2.70968 2.93548 3.32258 3.83871 4.58065 5.54839 6.51613 7.35484 7.93548 8.16129| 0.05 2.66451 0.45 3.05805 0.95 4.05807 1.45 5.97742 1.95 7.69999 2.45 8.1936 2.95 11.342 3.45 11.4065 3.95 7.6 4.45 7.6 4.95 7.6"
filament_unload_time = 11
filament_unloading_speed = 20

[filament:Generic PLA MMU2]
inherits = *PLA MMU2*

[filament:Prusa PLA MMU2]
inherits = *PLA MMU2*

[filament:Prusament PLA MMU2]
inherits = *PLA MMU2*

[filament:SemiFlex or Flexfill 98A]
inherits = *FLEX*
filament_cost = 82
filament_density = 1.22

[filament:Taulman Bridge]
inherits = *common*
filament_cost = 40
filament_density = 1.13
bed_temperature = 90
bridge_fan_speed = 40
cooling = 0
disable_fan_first_layers = 3
fan_always_on = 0
fan_below_layer_time = 20
filament_colour = #DEE0E6
filament_max_volumetric_speed = 10
filament_soluble = 0
filament_type = PET
first_layer_bed_temperature = 60
first_layer_temperature = 240
max_fan_speed = 5
min_fan_speed = 0
start_filament_gcode = "M900 K{if printer_notes=~/.*PRINTER_HAS_BOWDEN.*/}200{else}10{endif}; Filament gcode"
temperature = 250

[filament:Taulman T-Glase]
inherits = *PET*
filament_cost = 40
filament_density = 1.27
bridge_fan_speed = 40
cooling = 0
fan_always_on = 0
first_layer_bed_temperature = 90
first_layer_temperature = 240
max_fan_speed = 5
min_fan_speed = 0
start_filament_gcode = "M900 K{if printer_notes=~/.*PRINTER_HAS_BOWDEN.*/}200{else}30{endif}; Filament gcode"

[filament:Verbatim BVOH]
inherits = *common*
filament_cost = 218
filament_density = 1.23
bed_temperature = 60
bridge_fan_speed = 100
cooling = 0
disable_fan_first_layers = 1
extrusion_multiplier = 1
fan_always_on = 0
fan_below_layer_time = 100
filament_colour = #FFFFD7
filament_max_volumetric_speed = 4
filament_notes = "List of materials tested with standart PLA print settings for MK2:\n\nDas Filament\nEsun PLA\nEUMAKERS PLA\nFiberlogy HD-PLA\nFillamentum PLA\nFloreon3D\nHatchbox PLA\nPlasty Mladeč PLA\nPrimavalue PLA\nProto pasta Matte Fiber\nVerbatim PLA\nVerbatim BVOH"
filament_soluble = 1
filament_type = PLA
first_layer_bed_temperature = 60
first_layer_temperature = 215
max_fan_speed = 100
min_fan_speed = 100
start_filament_gcode = "M900 K{if printer_notes=~/.*PRINTER_HAS_BOWDEN.*/}200{else}10{endif}; Filament gcode"
temperature = 210

[filament:Verbatim BVOH MMU2]
inherits = Verbatim BVOH
compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK(2.5|3).*/ and single_extruder_multi_material
temperature = 195
filament_notes = BVOH
fan_always_on = 1
first_layer_temperature = 200
filament_cooling_final_speed = 1
filament_cooling_initial_speed = 2
filament_max_volumetric_speed = 4
filament_type = PVA
filament_cooling_moves = 1
filament_load_time = 12
filament_loading_speed = 14
filament_ramming_parameters = "120 110 1.74194 1.90323 2.16129 2.48387 2.83871 3.25806 3.83871 4.6129 5.41935 5.96774| 0.05 1.69677 0.45 1.96128 0.95 2.63872 1.45 3.46129 1.95 4.99031 2.45 6.12908 2.95 8.30974 3.45 11.4065 3.95 7.6 4.45 7.6 4.95 7.6"
filament_unload_time = 11
filament_unloading_speed = 20
filament_unloading_speed_start = 100

[filament:Verbatim PP]
inherits = *common*
filament_cost = 72
filament_density = 0.89
bed_temperature = 100
bridge_fan_speed = 100
cooling = 1
disable_fan_first_layers = 2
extrusion_multiplier = 1
fan_always_on = 1
fan_below_layer_time = 100
filament_colour = #DEE0E6
filament_max_volumetric_speed = 5
filament_notes = "List of materials tested with standart PLA print settings for MK2:\n\nEsun PLA\nFiberlogy HD-PLA\nFillamentum PLA\nFloreon3D\nHatchbox PLA\nPlasty Mladeč PLA\nPrimavalue PLA\nProto pasta Matte Fiber\nEUMAKERS PLA"
filament_type = PLA
first_layer_bed_temperature = 100
first_layer_temperature = 220
max_fan_speed = 100
min_fan_speed = 100
start_filament_gcode = "M900 K{if printer_notes=~/.*PRINTER_HAS_BOWDEN.*/}200{else}10{endif}; Filament gcode"
temperature = 220

[printer:*common*]
bed_shape = 0x0,250x0,250x210,0x210
before_layer_gcode = ;BEFORE_LAYER_CHANGE\nG92 E0.0\n;[layer_z]\n\n
between_objects_gcode = 
deretract_speed = 0
end_gcode = G4 ; wait\nM104 S0 ; turn off temperature\nM140 S0 ; turn off heatbed\nM107 ; turn off fan\n{if layer_z < max_print_height}G1 Z{z_offset+min(layer_z+30, max_print_height)}{endif} ; Move print head up\nG1 X0 Y200; home X axis\nM84 ; disable motors
extruder_colour = #FFFF00
extruder_offset = 0x0
gcode_flavor = marlin
silent_mode = 0
remaining_times = 0
machine_max_acceleration_e = 10000
machine_max_acceleration_extruding = 2000
machine_max_acceleration_retracting = 1500
machine_max_acceleration_x = 9000
machine_max_acceleration_y = 9000
machine_max_acceleration_z = 500
machine_max_feedrate_e = 120
machine_max_feedrate_x = 500
machine_max_feedrate_y = 500
machine_max_feedrate_z = 12
machine_max_jerk_e = 2.5
machine_max_jerk_x = 10
machine_max_jerk_y = 10
machine_max_jerk_z = 0.2
machine_min_extruding_rate = 0
machine_min_travel_rate = 0
layer_gcode = ;AFTER_LAYER_CHANGE\n;[layer_z]
max_layer_height = 0.25
min_layer_height = 0.07
max_print_height = 200
nozzle_diameter = 0.4
octoprint_apikey = 
octoprint_host = 
printer_notes = Don't remove the following keywords! These keywords are used in the "compatible printer" condition of the print and filament profiles to link the particular print and filament profiles to this printer profile.\nPRINTER_VENDOR_PRUSA3D\nPRINTER_MODEL_MK2\n
printer_settings_id = 
retract_before_travel = 1
retract_before_wipe = 0%
retract_layer_change = 1
retract_length = 0.8
retract_length_toolchange = 4
retract_lift = 0.6
retract_lift_above = 0
retract_lift_below = 199
retract_restart_extra = 0
retract_restart_extra_toolchange = 0
retract_speed = 35
serial_port = 
serial_speed = 250000
single_extruder_multi_material = 0
start_gcode = M115 U3.1.0 ; tell printer latest fw version\nM83  ; extruder relative mode\nM204 S[machine_max_acceleration_extruding] T[machine_max_acceleration_retracting] ; MK2 firmware only supports the old M204 format\nM104 S[first_layer_temperature] ; set extruder temp\nM140 S[first_layer_bed_temperature] ; set bed temp\nM190 S[first_layer_bed_temperature] ; wait for bed temp\nM109 S[first_layer_temperature] ; wait for extruder temp\nG28 W ; home all without mesh bed level\nG80 ; mesh bed leveling\nG1 Y-3.0 F1000.0 ; go outside print area\nG92 E0.0\nG1 X60.0 E9.0  F1000.0 ; intro line\nG1 X100.0 E12.5  F1000.0 ; intro line\nG92 E0.0
toolchange_gcode = 
use_firmware_retraction = 0
use_relative_e_distances = 1
use_volumetric_e = 0
variable_layer_height = 1
wipe = 1
z_offset = 0
printer_model = MK2S
printer_variant = 0.4
default_print_profile = 0.15mm OPTIMAL
default_filament_profile = Prusament PLA

[printer:*multimaterial*]
inherits = *common*
deretract_speed = 50
retract_before_travel = 3
retract_before_wipe = 60%
retract_layer_change = 0
retract_length = 4
retract_lift = 0.6
retract_lift_above = 0
retract_lift_below = 199
retract_restart_extra = 0
retract_restart_extra_toolchange = 0
retract_speed = 80
parking_pos_retraction = 92
cooling_tube_length = 5
cooling_tube_retraction = 91.5
single_extruder_multi_material = 1
printer_model = MK2SMM

[printer:*mm-single*]
inherits = *multimaterial*
end_gcode = G1 E-4 F2100.00000\nG91\nG1 Z1 F7200.000\nG90\nG1 X245 Y1\nG1 X240 E4\nG1 F4000\nG1 X190 E2.7  \nG1 F4600\nG1 X110 E2.8\nG1 F5200\nG1 X40 E3  \nG1 E-15.0000 F5000\nG1 E-50.0000 F5400\nG1 E-15.0000 F3000\nG1 E-12.0000 F2000\nG1 F1600\nG1 X0 Y1 E3.0000\nG1 X50 Y1 E-5.0000\nG1 F2000\nG1 X0 Y1 E5.0000\nG1 X50 Y1 E-5.0000\nG1 F2400\nG1 X0 Y1 E5.0000\nG1 X50 Y1 E-5.0000\nG1 F2400\nG1 X0 Y1 E5.0000\nG1 X50 Y1 E-3.0000\nG4 S0\nM107 ; turn off fan\n{if layer_z < max_print_height}G1 Z{z_offset+min(layer_z+30, max_print_height)}{endif} ; Move print head up\nM104 S0 ; turn off temperature\nM140 S0 ; turn off heatbed\nG28 X0  ; home X axis\nM84     ; disable motors\n\n
printer_notes = Don't remove the following keywords! These keywords are used in the "compatible printer" condition of the print and filament profiles to link the particular print and filament profiles to this printer profile.\nPRINTER_VENDOR_PRUSA3D\nPRINTER_MODEL_MK2\nPRINTER_HAS_BOWDEN
start_gcode = M115 U3.1.0 ; tell printer latest fw version\nM204 S[machine_max_acceleration_extruding] T[machine_max_acceleration_retracting] ; MK2 firmware only supports the old M204 format\n; Start G-Code sequence START\nT?\nM104 S[first_layer_temperature]\nM140 S[first_layer_bed_temperature]\nM109 S[first_layer_temperature]\nM190 S[first_layer_bed_temperature]\nG21 ; set units to millimeters\nG90 ; use absolute coordinates\nM83 ; use relative distances for extrusion\nG28 W\nG80\nG92 E0.0\nM203 E100\nM92 E140\nG1 Z0.250 F7200.000\nG1 X50.0 E80.0  F1000.0\nG1 X160.0 E20.0  F1000.0\nG1 Z0.200 F7200.000\nG1 X220.0 E13 F1000.0\nG1 X240.0 E0 F1000.0\nG1 E-4 F1000.0\nG92 E0.0
default_print_profile = 0.15mm OPTIMAL

[printer:*mm-multi*]
inherits = *multimaterial*
end_gcode = {if not has_wipe_tower}\n; Pull the filament into the cooling tubes.\nG1 E-4 F2100.00000\nG91\nG1 Z1 F7200.000\nG90\nG1 X245 Y1\nG1 X240 E4\nG1 F4000\nG1 X190 E2.7  \nG1 F4600\nG1 X110 E2.8\nG1 F5200\nG1 X40 E3  \nG1 E-15.0000 F5000\nG1 E-50.0000 F5400\nG1 E-15.0000 F3000\nG1 E-12.0000 F2000\nG1 F1600\nG1 X0 Y1 E3.0000\nG1 X50 Y1 E-5.0000\nG1 F2000\nG1 X0 Y1 E5.0000\nG1 X50 Y1 E-5.0000\nG1 F2400\nG1 X0 Y1 E5.0000\nG1 X50 Y1 E-5.0000\nG1 F2400\nG1 X0 Y1 E5.0000\nG1 X50 Y1 E-3.0000\nG4 S0\n{endif}\nM107 ; turn off fan\n{if layer_z < max_print_height}G1 Z{z_offset+min(layer_z+30, max_print_height)}{endif} ; Move print head up\nM104 S0 ; turn off temperature\nM140 S0 ; turn off heatbed\nG28 X0  ; home X axis\nM84     ; disable motors
extruder_colour = #FFAA55;#5182DB;#4ECDD3;#FB7259
nozzle_diameter = 0.4,0.4,0.4,0.4
printer_notes = Don't remove the following keywords! These keywords are used in the "compatible printer" condition of the print and filament profiles to link the particular print and filament profiles to this printer profile.\nPRINTER_VENDOR_PRUSA3D\nPRINTER_MODEL_MK2\nPRINTER_HAS_BOWDEN
start_gcode = M115 U3.1.0 ; tell printer latest fw version\nM204 S[machine_max_acceleration_extruding] T[machine_max_acceleration_retracting] ; MK2 firmware only supports the old M204 format\n; Start G-Code sequence START\nT[initial_tool]\nM104 S[first_layer_temperature] ; set extruder temp\nM140 S[first_layer_bed_temperature] ; set bed temp\nM190 S[first_layer_bed_temperature] ; wait for bed temp\nM109 S[first_layer_temperature] ; wait for extruder temp\nG21 ; set units to millimeters\nG90 ; use absolute coordinates\nM83 ; use relative distances for extrusion\nG28 W\nG80\nG92 E0.0\nM203 E100 ; set max feedrate\nM92 E140 ; E-steps per filament milimeter\n{if not has_single_extruder_multi_material_priming}\nG1 Z0.250 F7200.000\nG1 X50.0 E80.0  F1000.0\nG1 X160.0 E20.0  F1000.0\nG1 Z0.200 F7200.000\nG1 X220.0 E13 F1000.0\nG1 X240.0 E0 F1000.0\nG1 E-4 F1000.0\n{endif}\nG92 E0.0
variable_layer_height = 0
default_print_profile = 0.15mm OPTIMAL

# XXXXXXXXXXXXXXXXX
# XXX--- MK2 ---XXX
# XXXXXXXXXXXXXXXXX

[printer:Original Prusa i3 MK2]
inherits = *common*

[printer:Original Prusa i3 MK2 0.25 nozzle]
inherits = *common*
max_layer_height = 0.1
min_layer_height = 0.05
nozzle_diameter = 0.25
retract_length = 1
retract_speed = 50
variable_layer_height = 0
printer_variant = 0.25
default_print_profile = 0.10mm DETAIL 0.25 nozzle

[printer:Original Prusa i3 MK2 0.6 nozzle]
inherits = *common*
max_layer_height = 0.35
min_layer_height = 0.1
nozzle_diameter = 0.6
printer_variant = 0.6
default_print_profile = 0.20mm NORMAL 0.6 nozzle

# XXXXXXXXXXXXXXXXXXX
# XXX--- MK2MM ---XXX
# XXXXXXXXXXXXXXXXXXX

[printer:Original Prusa i3 MK2 MM Single Mode]
inherits = *mm-single*

[printer:Original Prusa i3 MK2 MM Single Mode 0.6 nozzle]
inherits = *mm-single*
nozzle_diameter = 0.6
printer_variant = 0.6
default_print_profile = 0.20mm NORMAL 0.6 nozzle

[printer:Original Prusa i3 MK2 MultiMaterial]
inherits = *mm-multi*
nozzle_diameter = 0.4,0.4,0.4,0.4

[printer:Original Prusa i3 MK2 MultiMaterial 0.6 nozzle]
inherits = *mm-multi*
nozzle_diameter = 0.6,0.6,0.6,0.6
printer_variant = 0.6
default_print_profile = 0.20mm NORMAL 0.6 nozzle

# XXXXXXXXXXXXXXXXXXX
# XXX--- MK2.5 ---XXX
# XXXXXXXXXXXXXXXXXXX

[printer:Original Prusa i3 MK2.5]
inherits = Original Prusa i3 MK2
printer_model = MK2.5
remaining_times = 1
start_gcode = M115 U3.4.1 ; tell printer latest fw version\nM83  ; extruder relative mode\nM104 S[first_layer_temperature] ; set extruder temp\nM140 S[first_layer_bed_temperature] ; set bed temp\nM190 S[first_layer_bed_temperature] ; wait for bed temp\nM109 S[first_layer_temperature] ; wait for extruder temp\nG28 W ; home all without mesh bed level\nG80 ; mesh bed leveling\nG1 Y-3.0 F1000.0 ; go outside print area\nG92 E0.0\nG1 X60.0 E9.0  F1000.0 ; intro line\nG1 X100.0 E12.5  F1000.0 ; intro line\nG92 E0.0

[printer:Original Prusa i3 MK2.5 MMU2 Single]
inherits = Original Prusa i3 MK2.5; *mm2*
printer_model = MK2.5MMU2
single_extruder_multi_material = 0
max_print_height = 200
remaining_times = 1
silent_mode = 0
retract_lift_below = 199
machine_max_acceleration_e = 10000
machine_max_acceleration_extruding = 2000
machine_max_acceleration_retracting = 1500
machine_max_acceleration_x = 9000
machine_max_acceleration_y = 9000
machine_max_acceleration_z = 500
machine_max_feedrate_e = 120
machine_max_feedrate_x = 500
machine_max_feedrate_y = 500
machine_max_feedrate_z = 12
machine_max_jerk_e = 2.5
machine_max_jerk_x = 10
machine_max_jerk_y = 10
machine_max_jerk_z = 0.2
machine_min_extruding_rate = 0
machine_min_travel_rate = 0
default_print_profile = 0.15mm OPTIMAL MK2.5
default_filament_profile = Prusament PLA
printer_notes = Don't remove the following keywords! These keywords are used in the "compatible printer" condition of the print and filament profiles to link the particular print and filament profiles to this printer profile.\nPRINTER_VENDOR_PRUSA3D\nPRINTER_MODEL_MK2.5\n
start_gcode = M107\nM115 U3.4.2 ; tell printer latest fw version\nM83  ; extruder relative mode\nM104 S[first_layer_temperature] ; set extruder temp\nM140 S[first_layer_bed_temperature] ; set bed temp\nM190 S[first_layer_bed_temperature] ; wait for bed temp\nM109 S[first_layer_temperature] ; wait for extruder temp\nG28 W ; home all without mesh bed level\nG80 ; mesh bed leveling\n\nG21 ; set units to millimeters\n\n;go outside print area\nG1 Y-3.0 F1000.0\nG1 Z0.4 F1000.0\n; select extruder\nT?\n; purge line\nG1 X55.0 E8.0 F2000.0\nG1 Z0.3 F1000.0\nG92 E0.0\nG1 X240.0 E25.0  F2200.0\nG1 Y-2.0 F1000.0\nG1 X55.0 E25 F1400.0\nG1 Z0.20 F1000.0\nG1 X5.0 E4.0 F1000.0\n\nM221 S{if layer_height<0.075}100{else}95{endif}\nG90 ; use absolute coordinates\nM83 ; use relative distances for extrusion\nG92 E0.0\n
end_gcode = G1 X0 Y210 F7200\nG1 E2 F5000\nG1 E2 F5500\nG1 E2 F6000\nG1 E-15.0000 F5800\nG1 E-20.0000 F5500\nG1 E10.0000 F3000\nG1 E-10.0000 F3100\nG1 E10.0000 F3150\nG1 E-10.0000 F3250\nG1 E10.0000 F3300\n\nM702 C\n\nG4 ; wait\nM104 S0 ; turn off temperature\nM140 S0 ; turn off heatbed\nM107 ; turn off fan\nG1 X0 Y200; home X axis\nM84 ; disable motors

[printer:Original Prusa i3 MK2.5 MMU2]
inherits = Original Prusa i3 MK2.5; *mm2*
printer_model = MK2.5MMU2
max_print_height = 200
remaining_times = 1
silent_mode = 0
retract_lift_below = 199
machine_max_acceleration_e = 10000
machine_max_acceleration_extruding = 2000
machine_max_acceleration_retracting = 1500
machine_max_acceleration_x = 9000
machine_max_acceleration_y = 9000
machine_max_acceleration_z = 500
machine_max_feedrate_e = 120
machine_max_feedrate_x = 500
machine_max_feedrate_y = 500
machine_max_feedrate_z = 12
machine_max_jerk_e = 2.5
machine_max_jerk_x = 10
machine_max_jerk_y = 10
machine_max_jerk_z = 0.2
machine_min_extruding_rate = 0
machine_min_travel_rate = 0
default_print_profile = 0.15mm OPTIMAL MK2.5
printer_notes = Don't remove the following keywords! These keywords are used in the "compatible printer" condition of the print and filament profiles to link the particular print and filament profiles to this printer profile.\nPRINTER_VENDOR_PRUSA3D\nPRINTER_MODEL_MK2.5\n
single_extruder_multi_material = 1
# The 5x nozzle diameter defines the number of extruders. Other extruder parameters
# (for example the retract values) are duplicaed from the first value, so they do not need 
# to be defined explicitely.
nozzle_diameter = 0.4,0.4,0.4,0.4,0.4
extruder_colour = #FF8000;#0080FF;#00FFFF;#FF4F4F;#9FFF9F
start_gcode = M107\nM115 U3.4.2 ; tell printer latest fw version\nM83  ; extruder relative mode\nM104 S[first_layer_temperature] ; set extruder temp\nM140 S[first_layer_bed_temperature] ; set bed temp\nM190 S[first_layer_bed_temperature] ; wait for bed temp\nM109 S[first_layer_temperature] ; wait for extruder temp\nG28 W ; home all without mesh bed level\nG80 ; mesh bed leveling\nG21 ; set units to millimeters\n\n; Send the filament type to the MMU2.0 unit.\n; E stands for extruder number, F stands for filament type (0: default; 1:flex; 2: PVA)\nM403 E0 F{"" + ((filament_type[0]=="FLEX") ? 1 : ((filament_type[0]=="PVA") ? 2 : 0))}\nM403 E1 F{"" + ((filament_type[1]=="FLEX") ? 1 : ((filament_type[1]=="PVA") ? 2 : 0))}\nM403 E2 F{"" + ((filament_type[2]=="FLEX") ? 1 : ((filament_type[2]=="PVA") ? 2 : 0))}\nM403 E3 F{"" + ((filament_type[3]=="FLEX") ? 1 : ((filament_type[3]=="PVA") ? 2 : 0))}\nM403 E4 F{"" + ((filament_type[4]=="FLEX") ? 1 : ((filament_type[4]=="PVA") ? 2 : 0))}\n\n{if not has_single_extruder_multi_material_priming}\n;go outside print area\nG1 Y-3.0 F1000.0\nG1 Z0.4 F1000.0\n; select extruder\nT[initial_tool]\n; initial load\nG1 X55.0 E32.0 F1073.0\nG1 X5.0 E32.0 F1800.0\nG1 X55.0 E8.0 F2000.0\nG1 Z0.3 F1000.0\nG92 E0.0\nG1 X240.0 E25.0  F2200.0\nG1 Y-2.0 F1000.0\nG1 X55.0 E25 F1400.0\nG1 Z0.20 F1000.0\nG1 X5.0 E4.0 F1000.0\nG92 E0.0\n{endif}\n\nM221 S{if layer_height<0.075}100{else}95{endif}\nG90 ; use absolute coordinates\nM83 ; use relative distances for extrusion\nG92 E0.0\n
end_gcode = {if has_wipe_tower}\nG1 E-15.0000 F3000\n{else}\nG1 X0 Y210 F7200\nG1 E2 F5000\nG1 E2 F5500\nG1 E2 F6000\nG1 E-15.0000 F5800\nG1 E-20.0000 F5500\nG1 E10.0000 F3000\nG1 E-10.0000 F3100\nG1 E10.0000 F3150\nG1 E-10.0000 F3250\nG1 E10.0000 F3300\n{endif}\n\n; Unload filament\nM702 C\n\nG4 ; wait\nM104 S0 ; turn off temperature\nM140 S0 ; turn off heatbed\nM107 ; turn off fan\n; Lift print head a bit\n{if layer_z < max_print_height}G1 Z{z_offset+min(layer_z+30, max_print_height)}{endif} ; Move print head up\nG1 X0 Y200; home X axis\nM84 ; disable motors\n

[printer:Original Prusa i3 MK2.5 0.25 nozzle]
inherits = Original Prusa i3 MK2 0.25 nozzle
printer_model = MK2.5
remaining_times = 1
start_gcode = M115 U3.4.1 ; tell printer latest fw version\nM83  ; extruder relative mode\nM104 S[first_layer_temperature] ; set extruder temp\nM140 S[first_layer_bed_temperature] ; set bed temp\nM190 S[first_layer_bed_temperature] ; wait for bed temp\nM109 S[first_layer_temperature] ; wait for extruder temp\nG28 W ; home all without mesh bed level\nG80 ; mesh bed leveling\nG1 Y-3.0 F1000.0 ; go outside print area\nG92 E0.0\nG1 X60.0 E9.0  F1000.0 ; intro line\nG1 X100.0 E12.5  F1000.0 ; intro line\nG92 E0.0

[printer:Original Prusa i3 MK2.5 0.6 nozzle]
inherits = Original Prusa i3 MK2 0.6 nozzle
printer_model = MK2.5
remaining_times = 1
start_gcode = M115 U3.4.1 ; tell printer latest fw version\nM83  ; extruder relative mode\nM104 S[first_layer_temperature] ; set extruder temp\nM140 S[first_layer_bed_temperature] ; set bed temp\nM190 S[first_layer_bed_temperature] ; wait for bed temp\nM109 S[first_layer_temperature] ; wait for extruder temp\nG28 W ; home all without mesh bed level\nG80 ; mesh bed leveling\nG1 Y-3.0 F1000.0 ; go outside print area\nG92 E0.0\nG1 X60.0 E9.0  F1000.0 ; intro line\nG1 X100.0 E12.5  F1000.0 ; intro line\nG92 E0.0

# XXXXXXXXXXXXXXXXX
# XXX--- MK3 ---XXX
# XXXXXXXXXXXXXXXXX

[printer:Original Prusa i3 MK3]
inherits = *common*
end_gcode = G4 ; wait\nM221 S100\nM104 S0 ; turn off temperature\nM140 S0 ; turn off heatbed\nM107 ; turn off fan\n{if layer_z < max_print_height}G1 Z{z_offset+min(layer_z+30, max_print_height)}{endif} ; Move print head up\nG1 X0 Y200; home X axis\nM84 ; disable motors
machine_max_acceleration_e = 5000,5000
machine_max_acceleration_extruding = 1250,1250
machine_max_acceleration_retracting = 1250,1250
machine_max_acceleration_x = 1000,960
machine_max_acceleration_y = 1000,960
machine_max_acceleration_z = 1000,1000
machine_max_feedrate_e = 120,120
machine_max_feedrate_x = 200,100
machine_max_feedrate_y = 200,100
machine_max_feedrate_z = 12,12
machine_max_jerk_e = 1.5,1.5
machine_max_jerk_x = 8,8
machine_max_jerk_y = 8,8
machine_max_jerk_z = 0.4,0.4
machine_min_extruding_rate = 0,0
machine_min_travel_rate = 0,0
silent_mode = 1
remaining_times = 1
printer_notes = Don't remove the following keywords! These keywords are used in the "compatible printer" condition of the print and filament profiles to link the particular print and filament profiles to this printer profile.\nPRINTER_VENDOR_PRUSA3D\nPRINTER_MODEL_MK3\n
retract_lift_below = 209
max_print_height = 210
start_gcode = M115 U3.4.1 ; tell printer latest fw version\nM83  ; extruder relative mode\nM104 S[first_layer_temperature] ; set extruder temp\nM140 S[first_layer_bed_temperature] ; set bed temp\nM190 S[first_layer_bed_temperature] ; wait for bed temp\nM109 S[first_layer_temperature] ; wait for extruder temp\nG28 W ; home all without mesh bed level\nG80 ; mesh bed leveling\nG1 Y-3.0 F1000.0 ; go outside print area\nG92 E0.0\nG1 X60.0 E9.0  F1000.0 ; intro line\nG1 X100.0 E12.5  F1000.0 ; intro line\nG92 E0.0\nM221 S{if layer_height==0.05}100{else}95{endif}
printer_model = MK3
default_print_profile = 0.15mm OPTIMAL MK3

[printer:Original Prusa i3 MK3 0.25 nozzle]
inherits = Original Prusa i3 MK3
nozzle_diameter = 0.25
max_layer_height = 0.1
min_layer_height = 0.05
printer_variant = 0.25
default_print_profile = 0.10mm DETAIL 0.25 nozzle MK3

[printer:Original Prusa i3 MK3 0.6 nozzle]
inherits = Original Prusa i3 MK3
nozzle_diameter = 0.6
max_layer_height = 0.35
min_layer_height = 0.1
printer_variant = 0.6
default_print_profile = 0.15mm OPTIMAL 0.6 nozzle MK3

[printer:*mm2*]
inherits = Original Prusa i3 MK3
single_extruder_multi_material = 1
cooling_tube_length = 10
cooling_tube_retraction = 30
parking_pos_retraction = 85
retract_length_toolchange = 3
extra_loading_move = -13
printer_model = MK3MMU2
default_print_profile = 0.15mm OPTIMAL MK3
default_filament_profile = Prusament PLA MMU2

[printer:Original Prusa i3 MK3 MMU2 Single]
inherits = *mm2*
single_extruder_multi_material = 0
start_gcode = M107\nM115 U3.4.1 ; tell printer latest fw version\nM83  ; extruder relative mode\nM104 S[first_layer_temperature] ; set extruder temp\nM140 S[first_layer_bed_temperature] ; set bed temp\nM190 S[first_layer_bed_temperature] ; wait for bed temp\nM109 S[first_layer_temperature] ; wait for extruder temp\nG28 W ; home all without mesh bed level\nG80 ; mesh bed leveling\n\nG21 ; set units to millimeters\n\n;go outside print area\nG1 Y-3.0 F1000.0\nG1 Z0.4 F1000.0\n; select extruder\nT?\n; purge line\nG1 X55.0 E8.0 F2000.0\nG1 Z0.3 F1000.0\nG92 E0.0\nG1 X240.0 E25.0  F2200.0\nG1 Y-2.0 F1000.0\nG1 X55.0 E25 F1400.0\nG1 Z0.20 F1000.0\nG1 X5.0 E4.0 F1000.0\n\nM221 S{if layer_height<0.075}100{else}95{endif}\nG90 ; use absolute coordinates\nM83 ; use relative distances for extrusion\nG92 E0.0\n
end_gcode = G1 X0 Y210 F7200\nG1 E2 F5000\nG1 E2 F5500\nG1 E2 F6000\nG1 E-15.0000 F5800\nG1 E-20.0000 F5500\nG1 E10.0000 F3000\nG1 E-10.0000 F3100\nG1 E10.0000 F3150\nG1 E-10.0000 F3250\nG1 E10.0000 F3300\n\nM702 C\n\nG4 ; wait\nM104 S0 ; turn off temperature\nM140 S0 ; turn off heatbed\nM107 ; turn off fan\nG1 X0 Y200; home X axis\nM84 ; disable motors

[printer:Original Prusa i3 MK3 MMU2]
inherits = *mm2*
# The 5x nozzle diameter defines the number of extruders. Other extruder parameters
# (for example the retract values) are duplicaed from the first value, so they do not need 
# to be defined explicitely.
machine_max_acceleration_e = 8000,8000
nozzle_diameter = 0.4,0.4,0.4,0.4,0.4
extruder_colour = #FF8000;#0080FF;#00FFFF;#FF4F4F;#9FFF9F
start_gcode = M107\nM115 U3.4.1 ; tell printer latest fw version\nM83  ; extruder relative mode\nM104 S[first_layer_temperature] ; set extruder temp\nM140 S[first_layer_bed_temperature] ; set bed temp\nM190 S[first_layer_bed_temperature] ; wait for bed temp\nM109 S[first_layer_temperature] ; wait for extruder temp\nG28 W ; home all without mesh bed level\nG80 ; mesh bed leveling\nG21 ; set units to millimeters\n\n; Send the filament type to the MMU2.0 unit.\n; E stands for extruder number, F stands for filament type (0: default; 1:flex; 2: PVA)\nM403 E0 F{"" + ((filament_type[0]=="FLEX") ? 1 : ((filament_type[0]=="PVA") ? 2 : 0))}\nM403 E1 F{"" + ((filament_type[1]=="FLEX") ? 1 : ((filament_type[1]=="PVA") ? 2 : 0))}\nM403 E2 F{"" + ((filament_type[2]=="FLEX") ? 1 : ((filament_type[2]=="PVA") ? 2 : 0))}\nM403 E3 F{"" + ((filament_type[3]=="FLEX") ? 1 : ((filament_type[3]=="PVA") ? 2 : 0))}\nM403 E4 F{"" + ((filament_type[4]=="FLEX") ? 1 : ((filament_type[4]=="PVA") ? 2 : 0))}\n\n{if not has_single_extruder_multi_material_priming}\n;go outside print area\nG1 Y-3.0 F1000.0\nG1 Z0.4 F1000.0\n; select extruder\nT[initial_tool]\n; initial load\nG1 X55.0 E32.0 F1073.0\nG1 X5.0 E32.0 F1800.0\nG1 X55.0 E8.0 F2000.0\nG1 Z0.3 F1000.0\nG92 E0.0\nG1 X240.0 E25.0  F2200.0\nG1 Y-2.0 F1000.0\nG1 X55.0 E25 F1400.0\nG1 Z0.20 F1000.0\nG1 X5.0 E4.0 F1000.0\nG92 E0.0\n{endif}\n\nM221 S{if layer_height<0.075}100{else}95{endif}\nG90 ; use absolute coordinates\nM83 ; use relative distances for extrusion\nG92 E0.0\n
end_gcode = {if has_wipe_tower}\nG1 E-15.0000 F3000\n{else}\nG1 X0 Y210 F7200\nG1 E2 F5000\nG1 E2 F5500\nG1 E2 F6000\nG1 E-15.0000 F5800\nG1 E-20.0000 F5500\nG1 E10.0000 F3000\nG1 E-10.0000 F3100\nG1 E10.0000 F3150\nG1 E-10.0000 F3250\nG1 E10.0000 F3300\n{endif}\n\n; Unload filament\nM702 C\n\nG4 ; wait\nM104 S0 ; turn off temperature\nM140 S0 ; turn off heatbed\nM107 ; turn off fan\n; Lift print head a bit\n{if layer_z < max_print_height}G1 Z{z_offset+min(layer_z+30, max_print_height)}{endif} ; Move print head up\nG1 X0 Y200; home X axis\nM84 ; disable motors\n

# The obsolete presets will be removed when upgrading from the legacy configuration structure (up to Slic3r 1.39.2) to 1.40.0 and newer.
[obsolete_presets]
print="0.05mm DETAIL 0.25 nozzle";"0.05mm DETAIL MK3";"0.05mm DETAIL";"0.20mm NORMAL MK3";"0.35mm FAST MK3";"print:0.15mm OPTIMAL MK3 MMU2";"print:0.20mm FAST MK3 MMU2"
filament="ColorFabb Brass Bronze 1.75mm";"ColorFabb HT 1.75mm";"ColorFabb nGen 1.75mm";"ColorFabb Woodfil 1.75mm";"ColorFabb XT 1.75mm";"ColorFabb XT-CF20 1.75mm";"E3D PC-ABS 1.75mm";"Fillamentum ABS 1.75mm";"Fillamentum ASA 1.75mm";"Generic ABS 1.75mm";"Generic PET 1.75mm";"Generic PLA 1.75mm";"Prusa ABS 1.75mm";"Prusa HIPS 1.75mm";"Prusa PET 1.75mm";"Prusa PLA 1.75mm";"Taulman Bridge 1.75mm";"Taulman T-Glase 1.75mm"