| 123456789101112131415161718192021222324252627282930313233343536373839404142434445464748495051525354555657585960616263646566676869707172737475767778798081828384858687888990919293949596979899100101102103104105106107108109110111112113114115116117 |
- #note: all settings are id$0 as the slicer consider there is only one value in the arrays in the gui.
- page:Filament:spool
- group:filament_spool_weight_event:Filament
- setting:id$0:filament_colour
- setting:id$0:filament_diameter
- setting:id$0:extrusion_multiplier
- setting:id$0:filament_density
- setting:id$0:filament_cost
- setting:id$0:filament_spool_weight
- group:Temperature °C
- line:Extruder
- setting:id$0:first_layer_temperature
- setting:id$0:temperature
- end_line
- line:Bed
- setting:id$0:first_layer_bed_temperature
- setting:id$0:label:Other layers:bed_temperature
- end_line
- setting:id$0:chamber_temperature
- group:Filament properties
- setting:id$0:width$7:filament_type
- setting:id$0:filament_soluble
- setting:id$0:filament_shrink
- setting:id$0:filament_max_overlap
- group:Print speed override
- setting:id$0:filament_max_speed
- setting:id$0:filament_max_volumetric_speed
- volumetric_speed_description
- page:Cooling:time
- group:Fan speed - default
- setting:id$0:default_fan_speed
- line:Perimeter fan speed
- setting:id$0:label_width$12:label$Internal:perimeter_fan_speed
- setting:id$0:label_width$12:label$External:external_perimeter_fan_speed
- line:Internal Infill fan speed
- setting:id$0:label_width$12:label$Sparse:infill_fan_speed
- line:Solid Infill fan speed
- setting:id$0:label_width$12:label$Solid:solid_infill_fan_speed
- setting:id$0:label_width$12:label$Top solid:top_fan_speed
- line:Support Material fan speed
- setting:id$0:label_width$12:label$Default:support_material_fan_speed
- setting:id$0:label_width$12:label$Interface:support_material_interface_fan_speed
- line:Bridges fan speed
- setting:id$0:label_width$12:label$Bridges:bridge_fan_speed
- setting:id$0:label_width$12:label$Internal bridges:bridge_internal_fan_speed
- line:Overhangs Perimeter fan speed
- setting:id$0:label_width$12:label$Overhangs:overhangs_fan_speed
- line:Gap fill fan speed
- setting:id$0:label_width$12:label$Gap fill:gap_fill_fan_speed
- line:Disable fan for the first
- setting:id$0:width$5:label$_:sidetext_width$7:disable_fan_first_layers
- setting:id$0:width$5:label_width$18:full_fan_speed_layer
- end_line
- group:Short layer time - began to increase base fan speed
- setting:id$0:fan_below_layer_time
- setting:id$0:label$Max fan speed:max_fan_speed
- group:Very short layer time - began to decrease extrusion rate
- setting:id$0:label$Layer time goal:slowdown_below_layer_time
- setting:id$0:width$4:max_speed_reduction
- setting:id$0:width$4:min_print_speed
- group:Behavior
- cooling_description
- page:Multimaterial:funnel
- group:Multimaterial toolchange temperature
- setting:id$0:filament_enable_toolchange_temp
- setting:id$0:filament_toolchange_temp
- setting:id$0:filament_use_fast_skinnydip
- setting:id$0:filament_enable_toolchange_part_fan
- setting:id$0:filament_toolchange_part_fan_speed
- group:Multimaterial toolchange string reduction
- setting:id$0:filament_use_skinnydip
- setting:id$0:filament_skinnydip_distance
- setting:id$0:filament_melt_zone_pause
- setting:id$0:filament_cooling_zone_pause
- setting:id$0:filament_dip_insertion_speed
- setting:id$0:filament_dip_extraction_speed
- group:Wipe tower parameters
- setting:id$0:filament_minimal_purge_on_wipe_tower
- setting:id$0:filament_max_wipe_tower_speed
- group:Toolchange parameters with single extruder MM printers
- setting:id$0:filament_loading_speed_start
- setting:id$0:filament_loading_speed
- setting:id$0:filament_unloading_speed_start
- setting:id$0:filament_unloading_speed
- setting:id$0:filament_load_time
- setting:id$0:filament_unload_time
- setting:id$0:filament_toolchange_delay
- setting:id$0:filament_cooling_moves
- setting:id$0:filament_cooling_initial_speed
- setting:id$0:filament_cooling_final_speed
- setting:id$0:filament_wipe_advanced_pigment
- filament_ramming_parameters
- filament_overrides_page
- page:Custom G-code:cog
- group:no_title:validate_gcode:Start G-code
- setting:id$0:full_width:height$35:start_filament_gcode
- group:no_title:validate_gcode:End G-code
- setting:id$0:full_width:height$35:end_filament_gcode
- page:Notes:note.png
- group:label_width$0:Notes
- setting:id$0:full_width:height$25:filament_notes
- group:label_width$0:Custom variables
- setting:id$0:full_width:height$15:filament_custom_variables
- page:Dependencies:wrench.png
- group:Profile dependencies
- setting:id$0:compatible_printers
- setting:id$0:full_width:color:compatible_printers_condition
- setting:id$0:compatible_prints
- setting:id$0:full_width:color:compatible_prints_condition
- parent_preset_description
|
