SuperSlicer/resources/profiles/Zonestar.ini

# Zonestar print profiles

# based on https://github.com/slic3r/slic3r-profiles/pull/19 by @ZONESTAR3D

[vendor]
repo_id = non-prusa-fff
# Vendor name will be shown by the Config Wizard.
name = Zonestar
# Configuration version of this file. Config file will only be installed, if the config_version differs.
# This means, the server may force the PrusaSlicer configuration to be downgraded.
config_version = 2.0.0
# Where to get the updates from?
config_update_url = https://files.prusa3d.com/wp-content/uploads/repository/PrusaSlicer-settings-master/live/Zonestar/

# The printer models will be shown by the Configuration Wizard in this order,
# also the first model installed & the first nozzle installed will be activated after install.
# Printer model name will be shown by the installation wizard.

[printer_model:Z5]
name = Zonestar Z5
variants = 0.4
technology = FFF
bed_model = bed_220.stl
bed_texture = 220_texture.svg
default_materials = Generic PLA @Zonestar; Generic ABS @Zonestar; Generic PETG @Zonestar; Generic TPU @Zonestar

[printer_model:Z6]
name = Zonestar Z6
variants = 0.4
technology = FFF
bed_model = bed_150.stl
bed_texture = 150_texture.svg
default_materials = Generic PLA @Zonestar; Generic ABS @Zonestar; Generic PETG @Zonestar; Generic TPU @Zonestar

[printer_model:Z5X]
name = Zonestar Z5X
variants = 0.4
technology = FFF
bed_model = bed_310.stl
bed_texture = 310_texture.svg
default_materials = Generic PLA @Zonestar; Generic ABS @Zonestar; Generic PETG @Zonestar; Generic TPU @Zonestar

[printer_model:Z8]
name = Zonestar Z8
variants = 0.4
technology = FFF
bed_model = bed_310.stl
bed_texture = 310_texture.svg
default_materials = Generic PLA @Zonestar; Generic ABS @Zonestar; Generic PETG @Zonestar; Generic TPU @Zonestar

[printer_model:Z9]
name = Zonestar Z9
variants = 0.4
technology = FFF
bed_model = bed_310.stl
bed_texture = 310_texture.svg
default_materials = Generic PLA @Zonestar; Generic ABS @Zonestar; Generic PETG @Zonestar; Generic TPU @Zonestar

###################
####   print   ####
###################

[print:*common*]
avoid_crossing_perimeters = 0
avoid_crossing_perimeters_max_detour = 0
bottom_fill_pattern = monotonic
bottom_solid_layers = 4
bottom_solid_min_thickness = 0
bridge_acceleration = 0
bridge_angle = 0
bridge_flow_ratio = 1
bridge_speed = 60
brim_separation = 0
brim_type = outer_only
brim_width = 4
clip_multipart_objects = 1
complete_objects = 0
default_acceleration = 0
dont_support_bridges = 1
draft_shield = disabled
elefant_foot_compensation = 0
ensure_vertical_shell_thickness = 1
external_perimeter_extrusion_width = 0.45
external_perimeter_speed = 50%
external_perimeters_first = 0
extra_perimeters = 0
extruder_clearance_height = 20
extruder_clearance_radius = 20
extrusion_width = 0.45
fill_angle = 45
fill_density = 20%
fill_pattern = grid
first_layer_acceleration = 0
first_layer_acceleration_over_raft = 0
first_layer_extrusion_width = 0.45
first_layer_height = 0.3
first_layer_speed = 25
first_layer_speed_over_raft = 30
fuzzy_skin = none
fuzzy_skin_point_dist = 0.8
fuzzy_skin_thickness = 0.3
gap_fill_enabled = 1
gap_fill_speed = 20
gcode_comments = 0
gcode_label_objects = 0
gcode_resolution = 0.0125
gcode_substitutions = 
infill_acceleration = 0
infill_anchor = 600%
infill_anchor_max = 50
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0.45
infill_first = 0
infill_only_where_needed = 0
infill_overlap = 25%
infill_speed = 60
inherits = 
interface_shells = 0
ironing = 0
ironing_flowrate = 15%
ironing_spacing = 0.1
ironing_speed = 15
ironing_type = top
layer_height = 0.2
max_print_speed = 80
max_volumetric_speed = 0
min_skirt_length = 0
mmu_segmented_region_max_width = 0
notes = 
only_retract_when_crossing_perimeters = 0
ooze_prevention = 0
output_filename_format = {printer_model}_{input_filename_base}.gcode
overhangs = 1
perimeter_acceleration = 0
perimeter_extruder = 1
perimeter_extrusion_width = 0.45
perimeter_speed = 50
perimeters = 3
post_process = 
print_settings_id = 
raft_contact_distance = 0.1
raft_expansion = 1.5
raft_first_layer_density = 90%
raft_first_layer_expansion = 3
raft_layers = 0
resolution = 0
seam_position = aligned
single_extruder_multi_material_priming = 0
skirt_distance = 6
skirt_height = 1
skirts = 0
slice_closing_radius = 0.049
slicing_mode = regular
small_perimeter_speed = 15
solid_infill_below_area = 0
solid_infill_every_layers = 0
solid_infill_extruder = 1
solid_infill_extrusion_width = 0.45
solid_infill_speed = 20
spiral_vase = 0
standby_temperature_delta = -5
support_material = 0
support_material_angle = 0
support_material_auto = 1
support_material_bottom_contact_distance = 0
support_material_bottom_interface_layers = -1
support_material_buildplate_only = 0
support_material_closing_radius = 2
support_material_contact_distance = 0.2
support_material_enforce_layers = 0
support_material_extruder = 1
support_material_extrusion_width = 0.35
support_material_interface_contact_loops = 0
support_material_interface_extruder = 1
support_material_interface_layers = 3
support_material_interface_pattern = rectilinear
support_material_interface_spacing = 0
support_material_interface_speed = 100%
support_material_pattern = rectilinear
support_material_spacing = 2.5
support_material_speed = 60
support_material_style = grid
support_material_synchronize_layers = 0
support_material_threshold = 0
support_material_with_sheath = 1
support_material_xy_spacing = 50%
thick_bridges = 1
thin_walls = 0
threads = 4
top_fill_pattern = monotonic
top_infill_extrusion_width = 0.4
top_solid_infill_speed = 15
top_solid_layers = 5
top_solid_min_thickness = 0
travel_speed = 100
travel_speed_z = 0
wipe_tower = 0
xy_size_compensation = 0
compatible_printers_condition = nozzle_diameter[0]==0.4 and num_extruders==1

[print:0.20mm @Zonestar MULTI]
inherits = *common*
wipe_tower = 1
wipe_tower_x = 125
wipe_tower_y = 195
compatible_printers_condition = nozzle_diameter[0]==0.4 and num_extruders>1


[print:0.20mm @Zonestar SINGLE]
inherits = *common*

###################
#### filament  ####
###################
[filament:Generic ABS @Zonestar]
bed_temperature = 100
bridge_fan_speed = 30
cooling = 1
disable_fan_first_layers = 3
extrusion_multiplier = 1
fan_always_on = 0
fan_below_layer_time = 60
filament_colour = #29B2B2
filament_cooling_final_speed = 3.4
filament_cooling_initial_speed = 2.2
filament_cooling_moves = 4
filament_cost = 0
filament_density = 0
filament_diameter = 1.75
filament_load_time = 0
filament_loading_speed = 28
filament_loading_speed_start = 3
filament_minimal_purge_on_wipe_tower = 50
filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
filament_type = ABS
filament_unloading_speed = 40
filament_unloading_speed_start = 60
filament_vendor = Generic
first_layer_bed_temperature = 100
first_layer_temperature = 245
max_fan_speed = 0
min_fan_speed = 0
min_print_speed = 15
slowdown_below_layer_time = 25
temperature = 245

[filament:Generic PETG @Zonestar]
bed_temperature = 70
bridge_fan_speed = 100
cooling = 1
disable_fan_first_layers = 3
end_filament_gcode = "; Filament-specific end gcode \n;END gcode for filament\n"
extrusion_multiplier = 1
fan_always_on = 1
fan_below_layer_time = 60
filament_colour = #29B2B2
filament_cooling_final_speed = 3.4
filament_cooling_initial_speed = 2.2
filament_cooling_moves = 4
filament_diameter = 1.75
filament_loading_speed = 28
filament_loading_speed_start = 3
filament_max_volumetric_speed = 0
filament_minimal_purge_on_wipe_tower = 50
filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
filament_spool_weight = 0
filament_toolchange_delay = 0
filament_type = PETG
filament_unloading_speed = 40
filament_unloading_speed_start = 60
filament_vendor = Generic
first_layer_bed_temperature = 70
first_layer_temperature = 210
full_fan_speed_layer = 0
max_fan_speed = 50
min_fan_speed = 25
min_print_speed = 10
slowdown_below_layer_time = 5
start_filament_gcode = "; Filament gcode\n"
temperature = 210

[filament:Generic PLA @Zonestar]
bed_temperature = 60
bridge_fan_speed = 100
cooling = 1
disable_fan_first_layers = 3
extrusion_multiplier = 1
fan_always_on = 1
fan_below_layer_time = 60
filament_colour = #29B2B2
filament_cooling_final_speed = 3.4
filament_cooling_initial_speed = 2.2
filament_cooling_moves = 4
filament_cost = 0
filament_density = 0
filament_diameter = 1.75
filament_loading_speed = 28
filament_loading_speed_start = 3
filament_max_volumetric_speed = 0
filament_minimal_purge_on_wipe_tower = 50
filament_notes = ""
filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
filament_toolchange_delay = 0
filament_type = PLA
filament_unloading_speed = 40
filament_unloading_speed_start = 60
filament_vendor = Generic
filament_wipe = nil
first_layer_bed_temperature = 60
first_layer_temperature = 200
full_fan_speed_layer = 5
max_fan_speed = 100
min_fan_speed = 50
min_print_speed = 10
slowdown_below_layer_time = 5
temperature = 200

[filament:Generic TPU @Zonestar]
bed_temperature = 50
bridge_fan_speed = 100
cooling = 1
disable_fan_first_layers = 3
extrusion_multiplier = 1
fan_always_on = 0
fan_below_layer_time = 60
filament_colour = #29B2B2
filament_cooling_final_speed = 3.4
filament_cooling_initial_speed = 2.2
filament_cooling_moves = 4
filament_diameter = 1.75
filament_loading_speed = 28
filament_loading_speed_start = 3
filament_max_volumetric_speed = 3
filament_minimal_purge_on_wipe_tower = 50
filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
filament_toolchange_delay = 0
filament_type = FLEX
filament_unloading_speed = 30
filament_unloading_speed_start = 30
filament_vendor = Generic
first_layer_bed_temperature = 50
first_layer_temperature = 225
full_fan_speed_layer = 0
max_fan_speed = 100
min_fan_speed = 50
min_print_speed = 10
slowdown_below_layer_time = 5
temperature = 225

###################
####  printer  ####
###################
[printer:*common*]
printer_technology = FFF
before_layer_gcode = 
between_objects_gcode = 
color_change_gcode = M600
cooling_tube_retraction = 35
default_filament_profile = 
default_print_profile = 
deretract_speed = 
end_gcode = 
extra_loading_move = -2
gcode_flavor = marlin2
high_current_on_filament_swap = 0
host_type = octoprint
layer_gcode = 
machine_limits_usage = ignore
machine_max_acceleration_e = 10000
machine_max_acceleration_extruding = 1500
machine_max_acceleration_retracting = 1500
machine_max_acceleration_travel = 1500
machine_max_acceleration_x = 9000
machine_max_acceleration_y = 9000
machine_max_acceleration_z = 500
machine_max_feedrate_e = 120
machine_max_feedrate_x = 500
machine_max_feedrate_y = 500
machine_max_feedrate_z = 12
machine_max_jerk_e = 2.5
machine_max_jerk_x = 10
machine_max_jerk_y = 10
machine_max_jerk_z = 0.2
machine_min_extruding_rate = 0
machine_min_travel_rate = 0
max_layer_height = 0.3
min_layer_height = 0.1
nozzle_diameter = 0.4
pause_print_gcode = 
remaining_times = 0
retract_speed = 40
silent_mode = 0
single_extruder_multi_material = 0
start_gcode = M104 S[first_layer_temperature] ; set extruder temp\nM140 S[first_layer_bed_temperature] ; set bed temp\nM190 S[first_layer_bed_temperature] ; wait for bed temp\nM109 S[first_layer_temperature] ; wait for extruder temp\nG28 ; home all axes\nG1 Z5 F3000 ; lift nozzle\nG1 X5 Y10 F1500 ; move to prime\nG1 Z0.2 F3000 ; get ready to prime\nG92 E0 ; reset extrusion distance\nG1 Y200 E15 F600 ; prime nozzle\nG1 Y100 F5000 ; quick wipe\nG92 E0
use_firmware_retraction = 0
use_relative_e_distances = 1
use_volumetric_e = 0
variable_layer_height = 0
wipe = 0
z_offset = 0

[printer:Zonestar Z5+M2 HOTEND]
inherits = *common*
printer_model = Z5
printer_variant = 0.4
bed_shape = 0x0,220x0,220x220,0x220
default_filament_profile = Generic PLA @Zonestar
default_print_profile = 0.20mm @Zonestar MULTI
deretract_speed = 30,30
before_layer_gcode = G92 E0
end_gcode = G28 X\nM106 S0 ; turn off FAN\nM104 S0 ; turn off extruder\nM140 S0 ; turn off bed\nM84 ; disable motors
extruder_colour = #FF0000;#00FF00
extruder_offset = 0x0,0x0
max_layer_height = 0.3,0.3
max_print_height = 220
min_layer_height = 0.15,0.15
nozzle_diameter = 0.4,0.4
retract_before_travel = 2,2
retract_before_wipe = 0%
retract_layer_change = 0
retract_length = 10,10
retract_length_toolchange = 0,0
retract_lift = 0,0
retract_lift_above = 0,0
retract_lift_below = 0,0
retract_restart_extra = 0,0
retract_restart_extra_toolchange = 0,0
retract_speed = 35,35
start_gcode = M104 S[first_layer_temperature] ; set extruder temp\nM140 S[first_layer_bed_temperature] ; set bed temp\nM190 S[first_layer_bed_temperature] ; wait for bed temp\nM109 S[first_layer_temperature] ; wait for extruder temp\nG28 ; home all axes\nG1 Z5 F3000 ; lift nozzle\nG1 X5 Y10 F1500 ; move to prime\nG1 Z0.2 F3000 ; get ready to prime\nT[initial_tool]\nG92 E0 ; reset extrusion distance\nG1 Y200 E15 F600 ; prime nozzle\nG1 Y100 F5000 ; quick wipe\nG92 E0
use_relative_e_distances = 1
wipe = 0,0


[printer:Zonestar Z6]
inherits = *common*
printer_model = Z6
printer_variant = 0.4
bed_shape = 0x0,150x0,150x150,0x150
default_filament_profile = Generic PLA @Zonestar
default_print_profile = 0.20mm @Zonestar SINGLE
deretract_speed = 30
end_gcode = G28 X\nM106 S0 ; turn off FAN\nM104 S0 ; turn off extruder\nM140 S0 ; turn off bed\nM84 ; disable motors
extruder_colour = #00FF00
extruder_offset = 0x0
min_layer_height = 0.1
max_layer_height = 0.3
max_print_height = 150
nozzle_diameter = 0.4
retract_before_travel = 2
retract_before_wipe = 0%
retract_layer_change = 0
retract_length = 6.5
retract_length_toolchange = 0
retract_lift = 0
retract_lift_above = 0
retract_lift_below = 0
retract_restart_extra = 0
retract_restart_extra_toolchange = 0
retract_speed = 40
start_gcode = M104 S[first_layer_temperature] ; set extruder temp\nM140 S[first_layer_bed_temperature] ; set bed temp\nM190 S[first_layer_bed_temperature] ; wait for bed temp\nM109 S[first_layer_temperature] ; wait for extruder temp\nG28 ; home all axes\nG1 Z5 F3000; lift nozzle\nG1 X5 Y5 F1500 ; move to prime\nG1 Z0.2 F3000 ; get ready to prime\nG92 E0 ; reset extrusion distance\nG1 Y100 E8 F600 ; prime nozzle\nG1 Y50 F5000 ; quick wipe\nG92 E0
use_relative_e_distances = 0

[printer:Zonestar Z5X]
inherits = *common*
printer_model = Z5X
printer_variant = 0.4
bed_shape = 0x0,310x0,310x310,0x310
default_filament_profile = Generic PLA @Zonestar
default_print_profile = 0.20mm @Zonestar SINGLE
deretract_speed = 30
end_gcode = G28 X\nM106 S0 ; turn off FAN\nM104 S0 ; turn off extruder\nM140 S0 ; turn off bed\nM84 ; disable motors
extruder_colour = #00FF00
extruder_offset = 0x0
min_layer_height = 0.1
max_layer_height = 0.3
max_print_height = 400
nozzle_diameter = 0.4
retract_before_travel = 2
retract_before_wipe = 0%
retract_layer_change = 0
retract_length = 6.5
retract_length_toolchange = 0
retract_lift = 0
retract_lift_above = 0
retract_lift_below = 0
retract_restart_extra = 0
retract_restart_extra_toolchange = 0
retract_speed = 40
start_gcode = M104 S[first_layer_temperature] ; set extruder temp\nM140 S[first_layer_bed_temperature] ; set bed temp\nM190 S[first_layer_bed_temperature] ; wait for bed temp\nM109 S[first_layer_temperature] ; wait for extruder temp\nG28 ; home all axes\nG1 Z5 F3000; lift nozzle\nG1 X5 Y5 F1500 ; move to prime\nG1 Z0.2 F3000 ; get ready to prime\nG92 E0 ; reset extrusion distance\nG1 Y200 E15 F600 ; prime nozzle\nG1 Y50 F5000 ; quick wipe\nG92 E0
use_relative_e_distances = 0

#Z8 with different types of hotend
[printer:Zonestar Z8+M3 HOTEND]
inherits = *common*
printer_model = Z8
printer_variant = 0.4
bed_shape = 0x0,310x0,310x310,0x310
default_filament_profile = Generic PLA @Zonestar
default_print_profile = 0.20mm @Zonestar MULTI
deretract_speed = 30,30,30
before_layer_gcode = G92 E0
end_gcode = G28 X\nM106 S0 ; turn off FAN\nM104 S0 ; turn off extruder\nM140 S0 ; turn off bed\nM84 ; disable motors
extruder_colour = #FF0000;#00FF00;#0000FF
extruder_offset = 0x0,0x0,0x0
max_layer_height = 0.3,0.3,0.3
max_print_height = 400
min_layer_height = 0.15,0.15,0.15
nozzle_diameter = 0.4,0.4,0.4
retract_before_travel = 2,2,2
retract_before_wipe = 0%,0%,0%
retract_layer_change = 0,0,0
retract_length = 10,10,10
retract_length_toolchange = 0,0,0
retract_lift = 0,0,0
retract_lift_above = 0,0,0
retract_lift_below = 0,0,0
retract_restart_extra = 0,0,0
retract_restart_extra_toolchange = 0,0,0
retract_speed = 35,35,35
start_gcode = M104 S[first_layer_temperature] ; set extruder temp\nM140 S[first_layer_bed_temperature] ; set bed temp\nM190 S[first_layer_bed_temperature] ; wait for bed temp\nM109 S[first_layer_temperature] ; wait for extruder temp\nG28 ; home all axes\nG1 Z5 F3000 ; lift nozzle\nG1 X5 Y10 F1500 ; move to prime\nG1 Z0.2 F3000 ; get ready to prime\nT[initial_tool]\nG92 E0 ; reset extrusion distance\nG1 Y200 E15 F600 ; prime nozzle\nG1 Y100 F5000 ; quick wipe\nG92 E0
use_relative_e_distances = 1
wipe = 0,0,0
layer_gcode = G92 E0

[printer:Zonestar Z8+M4 HOTEND]
inherits = *common*
printer_model = Z8
printer_variant = 0.4
bed_shape = 0x0,310x0,310x310,0x310
default_filament_profile = Generic PLA @Zonestar
default_print_profile = 0.20mm @Zonestar MULTI
deretract_speed = 30,30,30,30
before_layer_gcode = G92 E0
end_gcode = G28 X\nM106 S0 ; turn off FAN\nM104 S0 ; turn off extruder\nM140 S0 ; turn off bed\nM84 ; disable motors
extruder_colour = #E0E0E0;#FF0000;#00FF00;#0000FF
extruder_offset = 0x0,0x0,0x0,0x0
max_layer_height = 0.3,0.3,0.3,0.3
max_print_height = 400
min_layer_height = 0.15,0.15,0.15,0.15
nozzle_diameter = 0.4,0.4,0.4,0.4
retract_before_travel = 2,2,2,2
retract_before_wipe = 0%,0%,0%,0%
retract_layer_change = 0,0,0,0
retract_length = 10,10,10,10
retract_length_toolchange = 0,0,0,0
retract_lift = 0,0,0,0
retract_lift_above = 0,0,0,0
retract_lift_below = 0,0,0,0
retract_restart_extra = 0,0,0,0
retract_restart_extra_toolchange = 0,0,0,0
retract_speed = 35,35,35,35
start_gcode = M104 S[first_layer_temperature] ; set extruder temp\nM140 S[first_layer_bed_temperature] ; set bed temp\nM190 S[first_layer_bed_temperature] ; wait for bed temp\nM109 S[first_layer_temperature] ; wait for extruder temp\nG28 ; home all axes\nG1 Z5 F3000 ; lift nozzle\nG1 X5 Y10 F1500 ; move to prime\nG1 Z0.2 F3000 ; get ready to prime\nT[initial_tool]\nG92 E0 ; reset extrusion distance\nG1 Y200 E15 F600 ; prime nozzle\nG1 Y100 F5000 ; quick wipe\nG92 E0
use_relative_e_distances = 1
wipe = 0,0,0,0
layer_gcode = G92 E0

[printer:Zonestar Z8+E4 HOTEND]
inherits = *common*
printer_model = Z8
printer_variant = 0.4
bed_shape = 0x0,310x0,310x310,0x310
default_filament_profile = Generic PLA @Zonestar
default_print_profile = 0.20mm @Zonestar MULTI
deretract_speed = 30,30,30,30
before_layer_gcode = G92 E0
end_gcode = G1 E-30 F2100 ;pull out filament\nG28 X\nM106 S0 ; turn off FAN\nM104 S0 ; turn off extruder\nM140 S0 ; turn off bed\nM84 ; disable motors
extruder_colour = #E0E0E0;#FF0000;#00FF00;#0000FF
extruder_offset = 0x0,0x0,0x0,0x0
max_layer_height = 0.3,0.3,0.3,0.3
max_print_height = 400
min_layer_height = 0.1,0.1,0.1,0.1
nozzle_diameter = 0.4,0.4,0.4,0.4
retract_before_travel = 2,2,2,2
retract_before_wipe = 0%,0%,0%,0%
retract_layer_change = 0,0,0,0
retract_length = 8,8,8,8
retract_length_toolchange = 0,0,0,0
retract_lift = 0,0,0,0
retract_lift_above = 0,0,0,0
retract_lift_below = 0,0,0,0
retract_restart_extra = 0,0,0,0
retract_restart_extra_toolchange = 0,0,0,0
retract_speed = 35,35,35,35
start_gcode = M104 S[first_layer_temperature] ; set extruder temp\nM140 S[first_layer_bed_temperature] ; set bed temp\nM190 S[first_layer_bed_temperature] ; wait for bed temp\nM109 S[first_layer_temperature] ; wait for extruder temp\nG28 ; home all axes\nG1 Z5 F3000 ; lift nozzle\nG1 X5 Y10 F1500 ; move to prime\nG1 Z0.2 F3000 ; get ready to prime\nT[initial_tool]\nG92 E0 ; reset extrusion distance\nG1 Y200 E15 F600 ; prime nozzle\nG1 Y100 F5000 ; quick wipe\nG92 E0
toolchange_gcode = G92 E0\nG1 E-30 F1200;pull filament\nG92 E0\nT[next_extruder];Change extruder\nG92 E0\nG1 E15 F1800; push filament-1\nG1 E25 F900; pushfilament-2\nG1 E29 F1200; push filament-3\nG92 E0
use_relative_e_distances = 1
wipe = 0,0,0,0
layer_gcode = G92 E0

[printer:Zonestar Z8+DDE]
inherits = *common*
printer_model = Z8
printer_variant = 0.4
bed_shape = 0x0,310x0,310x310,0x310
default_filament_profile = Generic TPU @Zonestar
default_print_profile = 0.20mm @Zonestar SINGLE
deretract_speed = 30
end_gcode = G28 X\nM106 S0 ; turn off FAN\nM104 S0 ; turn off extruder\nM140 S0 ; turn off bed\nM84 ; disable motors
extruder_colour = #00FF00
extruder_offset = 0x0
max_layer_height = 0.3
max_print_height = 400
min_layer_height = 0.1
nozzle_diameter = 0.4
retract_before_travel = 2
retract_before_wipe = 0%
retract_layer_change = 0
retract_length = 6.5
retract_length_toolchange = 0
retract_lift = 0
retract_lift_above = 0
retract_lift_below = 0
retract_restart_extra = 0
retract_restart_extra_toolchange = 0
retract_speed = 40
start_gcode = M104 S[first_layer_temperature] ; set extruder temp\nM140 S[first_layer_bed_temperature] ; set bed temp\nM190 S[first_layer_bed_temperature] ; wait for bed temp\nM109 S[first_layer_temperature] ; wait for extruder temp\nG28 ; home all axes\nG1 Z5 F3000 ; lift nozzle\nG1 X5 Y10 F1500 ; move to prime\nG1 Z0.2 F3000 ; get ready to prime\nG92 E0 ; reset extrusion distance\nG1 Y200 E15 F600 ; prime nozzle\nG1 Y100 F5000 ; quick wipe\nG92 E0
use_relative_e_distances = 0

#Z9 with different types of hotend
[printer:Zonestar Z9+M3 HOTEND]
inherits = *common*
printer_model = Z9
printer_variant = 0.4
bed_shape = 0x0,310x0,310x310,0x310
default_filament_profile = Generic PLA @Zonestar
default_print_profile = 0.20mm @Zonestar MULTI
deretract_speed = 30,30,30
before_layer_gcode = G92 E0
end_gcode = G28 XY\nM106 S0 ; turn off FAN\nM104 S0 ; turn off extruder\nM140 S0 ; turn off bed\nM84 ; disable motors
extruder_colour = #FF0000;#00FF00;#0000FF
extruder_offset = 0x0,0x0,0x0
max_layer_height = 0.3,0.3,0.3
max_print_height = 400
min_layer_height = 0.15,0.15,0.15
nozzle_diameter = 0.4,0.4,0.4
retract_before_travel = 2,2,2
retract_before_wipe = 0%,0%,0%
retract_layer_change = 0,0,0
retract_length = 10,10,10
retract_length_toolchange = 0,0,0
retract_lift = 0,0,0
retract_lift_above = 0,0,0
retract_lift_below = 0,0,0
retract_restart_extra = 0,0,0
retract_restart_extra_toolchange = 0,0,0
retract_speed = 35,35,35
start_gcode = M104 S[first_layer_temperature] ; set extruder temp\nM140 S[first_layer_bed_temperature] ; set bed temp\nM190 S[first_layer_bed_temperature] ; wait for bed temp\nM109 S[first_layer_temperature] ; wait for extruder temp\nG28 ; home all axes\nG1 Z5 F3000 ; lift nozzle\nG1 X5 Y10 F1500 ; move to prime\nG1 Z0.2 F3000 ; get ready to prime\nT[initial_tool]\nG92 E0 ; reset extrusion distance\nG1 Y200 E15 F600 ; prime nozzle\nG1 Y100 F5000 ; quick wipe\nG92 E0
use_relative_e_distances = 1
wipe = 0,0,0
layer_gcode = G92 E0

[printer:Zonestar Z9+M4 HOTEND]
inherits = *common*
printer_model = Z9
printer_variant = 0.4
bed_shape = 0x0,310x0,310x310,0x310
default_filament_profile = Generic PLA @Zonestar
default_print_profile = 0.20mm @Zonestar MULTI
deretract_speed = 30,30,30,30
before_layer_gcode = G92 E0
end_gcode = G28 XY\nM106 S0 ; turn off FAN\nM104 S0 ; turn off extruder\nM140 S0 ; turn off bed\nM84 ; disable motors
extruder_colour = #E0E0E0;#FF0000;#00FF00;#0000FF
extruder_offset = 0x0,0x0,0x0,0x0
max_layer_height = 0.3,0.3,0.3,0.3
max_print_height = 400
min_layer_height = 0.15,0.15,0.15,0.15
nozzle_diameter = 0.4,0.4,0.4,0.4
retract_before_travel = 2,2,2,2
retract_before_wipe = 0%,0%,0%,0%
retract_layer_change = 0,0,0,0
retract_length = 10,10,10,10
retract_length_toolchange = 0,0,0,0
retract_lift = 0,0,0,0
retract_lift_above = 0,0,0,0
retract_lift_below = 0,0,0,0
retract_restart_extra = 0,0,0,0
retract_restart_extra_toolchange = 0,0,0,0
retract_speed = 35,35,35,35
start_gcode = M104 S[first_layer_temperature] ; set extruder temp\nM140 S[first_layer_bed_temperature] ; set bed temp\nM190 S[first_layer_bed_temperature] ; wait for bed temp\nM109 S[first_layer_temperature] ; wait for extruder temp\nG28 ; home all axes\nG1 Z5 F3000 ; lift nozzle\nG1 X5 Y10 F1500 ; move to prime\nG1 Z0.2 F3000 ; get ready to prime\nT[initial_tool]\nG92 E0 ; reset extrusion distance\nG1 Y200 E15 F600 ; prime nozzle\nG1 Y100 F5000 ; quick wipe\nG92 E0
use_relative_e_distances = 1
wipe = 0,0,0,0
layer_gcode = G92 E0

[printer:Zonestar Z9+E4 HOTEND]
inherits = *common*
printer_model = Z9
printer_variant = 0.4
bed_shape = 0x0,310x0,310x310,0x310
default_filament_profile = Generic PLA @Zonestar
default_print_profile = 0.20mm @Zonestar MULTI
deretract_speed = 30,30,30,30
before_layer_gcode = G92 E0
end_gcode = G1 E-30 F2100 ;pull out filament\nG28 XY\nM106 S0 ; turn off FAN\nM104 S0 ; turn off extruder\nM140 S0 ; turn off bed\nM84 ; disable motors
extruder_colour = #E0E0E0;#FF0000;#00FF00;#0000FF
extruder_offset = 0x0,0x0,0x0,0x0
max_layer_height = 0.3,0.3,0.3,0.3
max_print_height = 400
min_layer_height = 0.1,0.1,0.1,0.1
nozzle_diameter = 0.4,0.4,0.4,0.4
retract_before_travel = 2,2,2,2
retract_before_wipe = 0%,0%,0%,0%
retract_layer_change = 0,0,0,0
retract_length = 8,8,8,8
retract_length_toolchange = 0,0,0,0
retract_lift = 0,0,0,0
retract_lift_above = 0,0,0,0
retract_lift_below = 0,0,0,0
retract_restart_extra = 0,0,0,0
retract_restart_extra_toolchange = 0,0,0,0
retract_speed = 35,35,35,35
start_gcode = M104 S[first_layer_temperature] ; set extruder temp\nM140 S[first_layer_bed_temperature] ; set bed temp\nM190 S[first_layer_bed_temperature] ; wait for bed temp\nM109 S[first_layer_temperature] ; wait for extruder temp\nG28 ; home all axes\nG1 Z5 F3000 ; lift nozzle\nG1 X5 Y10 F1500 ; move to prime\nG1 Z0.2 F3000 ; get ready to prime\nT[initial_tool]\nG92 E0 ; reset extrusion distance\nG1 Y200 E15 F600 ; prime nozzle\nG1 Y100 F5000 ; quick wipe\nG92 E0
toolchange_gcode = G92 E0\nG1 E-30 F1200;pull filament\nG92 E0\nT[next_extruder];Change extruder\nG92 E0\nG1 E15 F1800; push filament-1\nG1 E25 F900; pushfilament-2\nG1 E29 F1200; push filament-3\nG92 E0
use_relative_e_distances = 1
wipe = 0,0,0,0
layer_gcode = G92 E0

[printer:Zonestar Z9+DDE]
inherits = *common*
printer_model = Z9
printer_variant = 0.4
bed_shape = 0x0,310x0,310x310,0x310
default_filament_profile = Generic TPU @Zonestar
default_print_profile = 0.20mm @Zonestar SINGLE
deretract_speed = 30
end_gcode = G28 XY\nM106 S0 ; turn off FAN\nM104 S0 ; turn off extruder\nM140 S0 ; turn off bed\nM84 ; disable motors
extruder_colour = #00FF00
extruder_offset = 0x0
max_layer_height = 0.3
max_print_height = 400
min_layer_height = 0.1
nozzle_diameter = 0.4
retract_before_travel = 2
retract_before_wipe = 0%
retract_layer_change = 0
retract_length = 6.5
retract_length_toolchange = 0
retract_lift = 0
retract_lift_above = 0
retract_lift_below = 0
retract_restart_extra = 0
retract_restart_extra_toolchange = 0
retract_speed = 40
start_gcode = M104 S[first_layer_temperature] ; set extruder temp\nM140 S[first_layer_bed_temperature] ; set bed temp\nM190 S[first_layer_bed_temperature] ; wait for bed temp\nM109 S[first_layer_temperature] ; wait for extruder temp\nG28 ; home all axes\nG1 Z5 F3000 ; lift nozzle\nG1 X5 Y10 F1500 ; move to prime\nG1 Z0.2 F3000 ; get ready to prime\nG92 E0 ; reset extrusion distance\nG1 Y200 E15 F600 ; prime nozzle\nG1 Y100 F5000 ; quick wipe\nG92 E0
use_relative_e_distances = 0