| 1234567891011121314151617181920212223242526272829303132333435363738394041424344454647484950515253545556575859606162636465666768697071727374757677787980818283848586878889909192939495 |
- page:Filament:spool
- group:Filament
- setting:filament_colour
- setting:filament_diameter
- setting:extrusion_multiplier
- setting:filament_density
- setting:filament_cost
- group:Temperature °C
- line:Extruder
- setting:first_layer_temperature
- setting:temperature
- end_line
- line:Bed
- setting:first_layer_bed_temperature
- setting:label:Other layers:bed_temperature
- end_line
- setting:chamber_temperature
- group:Filament properties
- setting:width$7:filament_type
- setting:filament_soluble
- setting:filament_shrink
- group:Print speed override
- setting:filament_max_wipe_tower_speed
- setting:filament_max_volumetric_speed
- volumetric_speed_description
- page:Cooling:time
- group:Fan speed - default
- setting:label$Run the fan at default speed when possible:fan_always_on
- setting:min_fan_speed
- setting:bridge_fan_speed
- setting:top_fan_speed
- setting:external_perimeter_fan_speed
- setting:disable_fan_first_layers
- group:Short layer time - began to increase base fan speed
- setting:fan_below_layer_time
- setting:label$Max fan speed:max_fan_speed
- group:Very short layer time - began to decrease extrusion rate
- setting:label$Layer time goal:slowdown_below_layer_time
- setting:width$4:max_speed_reduction
- setting:width$4:min_print_speed
- group:Behavior
- cooling_description
- page:Multimaterial:funnel
- group:Multimaterial toolchange temperature
- setting:filament_enable_toolchange_temp
- setting:filament_toolchange_temp
- setting:filament_use_fast_skinnydip
- setting:filament_enable_toolchange_part_fan
- setting:filament_toolchange_part_fan_speed
- group:Multimaterial toolchange string reduction
- setting:filament_use_skinnydip
- setting:filament_skinnydip_distance
- setting:filament_melt_zone_pause
- setting:filament_cooling_zone_pause
- setting:filament_dip_insertion_speed
- setting:filament_dip_extraction_speed
- group:Wipe tower parameters
- setting:filament_minimal_purge_on_wipe_tower
- group:Toolchange parameters with single extruder MM printers
- setting:filament_loading_speed_start
- setting:filament_loading_speed
- setting:filament_unloading_speed_start
- setting:filament_unloading_speed
- setting:filament_load_time
- setting:filament_unload_time
- setting:filament_toolchange_delay
- setting:filament_cooling_moves
- setting:filament_cooling_initial_speed
- setting:filament_cooling_final_speed
- setting:filament_wipe_advanced_pigment
- filament_ramming_parameters
- filament_overrides_page
- page:Custom G-code:cog
- group:nolabel:Start G-code
- setting:full_width:height$35:start_filament_gcode
- group:nolabel:End G-code
- setting:full_width:height$35:end_filament_gcode
- page:Notes:note.png
- group:label_width$0:Notes
- setting:full_width:height$25:filament_notes
- page:Dependencies:wrench.png
- group:Profile dependencies
- setting:compatible_printers
- setting:full_width:color:compatible_printers_condition
- setting:compatible_prints
- setting:full_width:color:compatible_prints_condition
- parent_preset_description
|
