netdata/database

Database

Netdata is fully capable of long-term metrics storage, at per-second granularity, via its default database engine (dbengine). But to remain as flexible as possible, Netdata supports several storage options:

1. dbengine, (the default) data are in database files. The Database Engine works like a traditional database. There is some amount of RAM dedicated to data caching and indexing and the rest of the data reside compressed on disk. The number of history entries is not fixed in this case, but depends on the configured disk space and the effective compression ratio of the data stored. This is the only mode that supports changing the data collection update frequency (update every) without losing the previously stored metrics. For more details see here.

2. ram, data are purely in memory. Data are never saved on disk. This mode uses mmap() and supports KSM.

3. save, data are only in RAM while Netdata runs and are saved to / loaded from disk on Netdata restart. It also uses mmap() and supports KSM.

4. map, data are in memory mapped files. This works like the swap. When Netdata writes data on its memory, the Linux kernel marks the related memory pages as dirty and automatically starts updating them on disk. Unfortunately we cannot control how frequently this works. The Linux kernel uses exactly the same algorithm it uses for its swap memory. This mode uses mmap() but does not support KSM. Keep in mind though, this option will have a constant write on your disk.

5. alloc, like ram but it uses calloc() and does not support KSM. This mode is the fallback for all others except none.

6. none, without a database (collected metrics can only be streamed to another Netdata).

Which database mode to use

The default mode [db].mode = dbengine has been designed to scale for longer retentions and is the only mode suitable for parent Agents in the Parent - Child setups

The other available database modes are designed to minimize resource utilization and should only be considered on Parent - Child setups at the children side and only when the resource constraints are very strict.

So,

• On a single node setup, use [db].mode = dbengine.
• On a Parent - Child setup, use [db].mode = dbengine on the parent to increase retention, a more resource efficient mode like, dbengine with light retention settings, and save, ram or none modes for the children to minimize resource utilization.

Choose your database mode

You can select the database mode by editing netdata.conf and setting:

[db]
  # dbengine (default), ram, save (the default if dbengine not available), map (swap like), none, alloc
  mode = dbengine

Netdata Longer Metrics Retention

Metrics retention is controlled only by the disk space allocated to storing metrics. But it also affects the memory and CPU required by the agent to query longer timeframes.

Since Netdata Agents usually run on the edge, on production systems, Netdata Agent parents should be considered. When having a parent - child setup, the child (the Netdata Agent running on a production system) delegates all of its functions, including longer metrics retention and querying, to the parent node that can dedicate more resources to this task. A single Netdata Agent parent can centralize multiple children Netdata Agents (dozens, hundreds, or even thousands depending on its available resources).

Running Netdata on embedded devices

Embedded devices typically have very limited RAM resources available.

There are two settings for you to configure:

1. [db].update every, which controls the data collection frequency
2. [db].retention, which controls the size of the database in memory (except for [db].mode = dbengine)

By default [db].update every = 1 and [db].retention = 3600. This gives you an hour of data with per second updates.

If you set [db].update every = 2 and [db].retention = 1800, you will still have an hour of data, but collected once every 2 seconds. This will cut in half both CPU and RAM resources consumed by Netdata. Of course experiment a bit to find the right setting. On very weak devices you might have to use [db].update every = 5 and [db].retention = 720 (still 1 hour of data, but 1/5 of the CPU and RAM resources).

You can also disable data collection plugins that you don't need. Disabling such plugins will also free both CPU and RAM resources.

Memory optimizations

KSM

KSM performs memory deduplication by scanning through main memory for physical pages that have identical content, and identifies the virtual pages that are mapped to those physical pages. It leaves one page unchanged, and re-maps each duplicate page to point to the same physical page. Netdata offers all of its in-memory database to kernel for deduplication.

In the past, KSM has been criticized for consuming a lot of CPU resources. This is true when KSM is used for deduplicating certain applications, but it is not true for Netdata. Agent's memory is written very infrequently (if you have 24 hours of metrics in Netdata, each byte at the in-memory database will be updated just once per day). KSM is a solution that will provide 60+% memory savings to Netdata.

Enable KSM in kernel

To enable KSM in kernel, you need to run a kernel compiled with the following:

CONFIG_KSM=y

When KSM is enabled at the kernel, it is just available for the user to enable it.

If you build a kernel with CONFIG_KSM=y, you will just get a few files in /sys/kernel/mm/ksm. Nothing else happens. There is no performance penalty (apart from the memory this code occupies into the kernel).

The files that CONFIG_KSM=y offers include:

• /sys/kernel/mm/ksm/run by default 0. You have to set this to 1 for the kernel to spawn ksmd.
• /sys/kernel/mm/ksm/sleep_millisecs, by default 20. The frequency ksmd should evaluate memory for deduplication.
• /sys/kernel/mm/ksm/pages_to_scan, by default 100. The amount of pages ksmd will evaluate on each run.

So, by default ksmd is just disabled. It will not harm performance and the user/admin can control the CPU resources they are willing to have used by ksmd.

Run ksmd kernel daemon

To activate / run ksmd, you need to run the following:

echo 1 >/sys/kernel/mm/ksm/run
echo 1000 >/sys/kernel/mm/ksm/sleep_millisecs

With these settings, ksmd does not even appear in the running process list (it will run once per second and evaluate 100 pages for de-duplication).

Put the above lines in your boot sequence (/etc/rc.local or equivalent) to have ksmd run at boot.

Monitoring Kernel Memory de-duplication performance

Netdata will create charts for kernel memory de-duplication performance, like this: