#!/usr/bin/env bash
#
# Build tests for LPC1768 (NXP ARM Cortex-M3)
#

# exit on first failure
set -e

#
# Build with the default configurations
#
#restore_configs
#opt_set MOTHERBOARD BOARD_RAMPS_14_RE_ARM_EFB
#exec_test $1 $2 "Default Configuration" "$3"

restore_configs
opt_set MOTHERBOARD BOARD_RAMPS_14_RE_ARM_EFB SERIAL_PORT_3 3 \
        NEOPIXEL_TYPE NEO_RGB RGB_LED_R_PIN P2_12 RGB_LED_G_PIN P1_23 RGB_LED_B_PIN P1_22 RGB_LED_W_PIN P1_24
opt_enable FYSETC_MINI_12864_2_1 SDSUPPORT SDCARD_READONLY SERIAL_PORT_2 RGBW_LED E_DUAL_STEPPER_DRIVERS \
           NEOPIXEL_LED NEOPIXEL_IS_SEQUENTIAL NEOPIXEL_STARTUP_TEST NEOPIXEL_BKGD_INDEX_FIRST NEOPIXEL_BKGD_INDEX_LAST \
           NEOPIXEL_BKGD_COLOR NEOPIXEL_BKGD_TIMEOUT_COLOR NEOPIXEL_BKGD_ALWAYS_ON \
           PINS_DEBUGGING
exec_test $1 $2 "ReARM EFB VIKI2, SDSUPPORT, 2 Serial ports (USB CDC + UART0), NeoPixel" "$3"

#restore_configs
#use_example_configs Mks/Sbase
#exec_test $1 $2 "MKS SBASE Example Config" "$3"

restore_configs
opt_set MOTHERBOARD BOARD_MKS_SBASE \
        EXTRUDERS 2 TEMP_SENSOR_1 1 \
        NUM_SERVOS 2 SERVO_DELAY '{ 300, 300 }' SWITCHING_NOZZLE_SERVO_ANGLES '{ { 0, 90 }, { 90, 0 } }'
opt_enable SWITCHING_NOZZLE SWITCHING_NOZZLE_E1_SERVO_NR EDITABLE_SERVO_ANGLES SERVO_DETACH_GCODE \
           ULTIMAKERCONTROLLER REALTIME_REPORTING_COMMANDS FULL_REPORT_TO_HOST_FEATURE
exec_test $1 $2 "MKS SBASE with SWITCHING_NOZZLE, Grbl Realtime Report" "$3"

restore_configs
opt_set MOTHERBOARD BOARD_RAMPS_14_RE_ARM_EEB \
        EXTRUDERS 2 TEMP_SENSOR_1 -4 TEMP_SENSOR_BED 5 \
        GRID_MAX_POINTS_X 16 \
        NOZZLE_TO_PROBE_OFFSET '{ 0, 0, 0 }' \
        NOZZLE_CLEAN_MIN_TEMP 170 \
        NOZZLE_CLEAN_START_POINT "{ {  10, 10, 3 }, {  10, 10, 3 } }" \
        NOZZLE_CLEAN_END_POINT "{ {  10, 20, 3 }, {  10, 20, 3 } }"
opt_enable REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER ADAPTIVE_FAN_SLOWING TEMP_TUNING_MAINTAIN_FAN \
           FILAMENT_WIDTH_SENSOR FILAMENT_LCD_DISPLAY PID_EXTRUSION_SCALING SOUND_MENU_ITEM \
           NOZZLE_AS_PROBE AUTO_BED_LEVELING_BILINEAR PREHEAT_BEFORE_LEVELING G29_RETRY_AND_RECOVER Z_MIN_PROBE_REPEATABILITY_TEST DEBUG_LEVELING_FEATURE \
           ASSISTED_TRAMMING ASSISTED_TRAMMING_WIZARD REPORT_TRAMMING_MM ASSISTED_TRAMMING_WAIT_POSITION \
           BABYSTEPPING BABYSTEP_XY BABYSTEP_ZPROBE_OFFSET EP_BABYSTEPPING BABYSTEP_GFX_OVERLAY \
           PRINTCOUNTER NOZZLE_PARK_FEATURE NOZZLE_CLEAN_FEATURE SLOW_PWM_HEATERS PIDTEMPBED EEPROM_SETTINGS INCH_MODE_SUPPORT TEMPERATURE_UNITS_SUPPORT \
           Z_SAFE_HOMING ADVANCED_PAUSE_FEATURE PARK_HEAD_ON_PAUSE \
           HOST_KEEPALIVE_FEATURE HOST_ACTION_COMMANDS HOST_PROMPT_SUPPORT HOST_STATUS_NOTIFICATIONS \
           LCD_INFO_MENU ARC_SUPPORT BEZIER_CURVE_SUPPORT EXTENDED_CAPABILITIES_REPORT AUTO_REPORT_TEMPERATURES \
           SDSUPPORT SDCARD_SORT_ALPHA AUTO_REPORT_SD_STATUS EMERGENCY_PARSER SOFT_RESET_ON_KILL SOFT_RESET_VIA_SERIAL
exec_test $1 $2 "Re-ARM with NOZZLE_AS_PROBE and many features." "$3"

restore_configs
opt_set MOTHERBOARD BOARD_BTT_SKR_V1_3 EXTRUDERS 2 \
        TEMP_SENSOR_0 1 TEMP_SENSOR_1 1 TEMP_SENSOR_BED 1 TEMP_SENSOR_CHAMBER 1 \
        TEMP_CHAMBER_PIN P1_30 HEATER_CHAMBER_PIN P0_28
opt_enable PIDTEMPBED PIDTEMPCHAMBER PID_EXTRUSION_SCALING PID_FAN_SCALING
exec_test $1 $2 "SKR v1.3 with 2*Extr, bed, chamber all PID." "$3"

#
# SKR 1.4 with MMU2
#
restore_configs
opt_set MOTHERBOARD BOARD_BTT_SKR_V1_4 SERIAL_PORT -1 \
        BAUDRATE 115200 X_DRIVER_TYPE TMC2209 Y_DRIVER_TYPE TMC2209 \
        Z_DRIVER_TYPE TMC2209 Z2_DRIVER_TYPE TMC2209 E0_DRIVER_TYPE TMC2209 \
        EXTRUDERS 5 MMU_MODEL PRUSA_MMU2 HEATER_0_MAXTEMP 305 \
        BED_MAXTEMP 125 HOTEND_OVERSHOOT 5 INVERT_X_DIR true \
        INVERT_E0_DIR true X_BED_SIZE 235 Y_BED_SIZE 225 Z_MAX_POS 240 \
        GRID_MAX_POINTS_X 5 E0_AUTO_FAN_PIN FAN1_PIN \
        BLTOUCH_HS_MODE true BLTOUCH_HS_EXTRA_CLEARANCE 0 \
        Z_STEPPER_ALIGN_XY '{{10,110},{200,110}}' \
        Z_STEPPER_ALIGN_ITERATIONS 10 DEFAULT_STEPPER_TIMEOUT_SEC 0 \
        SLOWDOWN_DIVISOR 16 SDCARD_CONNECTION ONBOARD BLOCK_BUFFER_SIZE 64 \
        CHOPPER_TIMING CHOPPER_DEFAULT_24V MMU_SERIAL_PORT 0
opt_enable PIDTEMPBED S_CURVE_ACCELERATION \
        USE_PROBE_FOR_Z_HOMING BLTOUCH FILAMENT_RUNOUT_SENSOR \
        AUTO_BED_LEVELING_BILINEAR RESTORE_LEVELING_AFTER_G28 \
        EXTRAPOLATE_BEYOND_GRID LCD_BED_LEVELING MESH_EDIT_MENU Z_SAFE_HOMING \
        EEPROM_SETTINGS EEPROM_AUTO_INIT NOZZLE_PARK_FEATURE SDSUPPORT \
        SPEAKER CR10_STOCKDISPLAY QUICK_HOME BLTOUCH_FORCE_SW_MODE \
        Z_STEPPER_AUTO_ALIGN INPUT_SHAPING_X INPUT_SHAPING_Y SHAPING_MENU \
        ADAPTIVE_STEP_SMOOTHING LCD_INFO_MENU STATUS_MESSAGE_SCROLLING \
        SET_PROGRESS_MANUALLY M73_REPORT SHOW_REMAINING_TIME \
        PRINT_PROGRESS_SHOW_DECIMALS AUTO_REPORT_SD_STATUS USE_BIG_EDIT_FONT \
        BABYSTEPPING BABYSTEP_WITHOUT_HOMING BABYSTEP_ALWAYS_AVAILABLE \
        DOUBLECLICK_FOR_Z_BABYSTEPPING BABYSTEP_DISPLAY_TOTAL LIN_ADVANCE \
        BEZIER_CURVE_SUPPORT EMERGENCY_PARSER ADVANCED_PAUSE_FEATURE \
        TMC_DEBUG HOST_ACTION_COMMANDS HOST_PAUSE_M76 HOST_PROMPT_SUPPORT \
        HOST_STATUS_NOTIFICATIONS MMU_DEBUG
opt_disable Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN FILAMENT_LOAD_UNLOAD_GCODES \
        PARK_HEAD_ON_PAUSE
exec_test $1 $2 "BigTreeTech SKR 1.4 | MMU2" "$3"