/* Copyright (c) 2011 Arduino. All right reserved. This library is free software; you can redistribute it and/or modify it under the terms of the GNU Lesser General Public License as published by the Free Software Foundation; either version 2.1 of the License, or (at your option) any later version. This library is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU Lesser General Public License for more details. You should have received a copy of the GNU Lesser General Public License along with this library; if not, write to the Free Software Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA */ #ifndef _VARIANT_ARDUINO_DUE_X_ #define _VARIANT_ARDUINO_DUE_X_ /*---------------------------------------------------------------------------- * Definitions *----------------------------------------------------------------------------*/ /** Frequency of the board main oscillator */ #define VARIANT_MAINOSC 12000000 /** Master clock frequency */ #define VARIANT_MCK 84000000 /*---------------------------------------------------------------------------- * Headers *----------------------------------------------------------------------------*/ #include "Arduino.h" #ifdef __cplusplus #include "UARTClass.h" #include "USARTClass.h" #endif #ifdef __cplusplus extern "C"{ #endif // __cplusplus /** * Libc porting layers */ #if defined ( __GNUC__ ) /* GCC CS3 */ # include /** RedHat Newlib minimal stub */ #endif /*---------------------------------------------------------------------------- * Pins *----------------------------------------------------------------------------*/ // Number of pins defined in PinDescription array #define PINS_COUNT 79 #define NUM_DIGITAL_PINS 66 #define NUM_ANALOG_INPUTS 12 #define analogInputToDigitalPin(p) pin_t((p < 12) ? (p) + 54 : -1) #define digitalPinToPort(P) ( g_APinDescription[P].pPort ) #define digitalPinToBitMask(P) ( g_APinDescription[P].ulPin ) //#define analogInPinToBit(P) ( ) #define portOutputRegister(port) ( &(port->PIO_ODSR) ) #define portInputRegister(port) ( &(port->PIO_PDSR) ) #define digitalPinHasPWM(P) ( g_APinDescription[P].ulPWMChannel != NOT_ON_PWM || g_APinDescription[P].ulTCChannel != NOT_ON_TIMER ) /* * portModeRegister(..) should return a register to set pin mode * INPUT or OUTPUT by setting the corresponding bit to 0 or 1. * Unfortunately on SAM architecture the PIO_OSR register is * read-only and can be set only through the enable/disable registers * pair PIO_OER/PIO_ODR. */ // #define portModeRegister(port) ( &(port->PIO_OSR) ) /* * digitalPinToTimer(..) is AVR-specific and is not defined for SAM * architecture. If you need to check if a pin supports PWM you must * use digitalPinHasPWM(..). * * https://github.com/arduino/Arduino/issues/1833 */ // #define digitalPinToTimer(P) // Interrupts #define digitalPinToInterrupt(p) ((p) < NUM_DIGITAL_PINS ? (p) : -1) // LEDs #define PIN_LED_13 (13U) #define PIN_LED_RXL (72U) #define PIN_LED_TXL (73U) #define PIN_LED PIN_LED_13 #define PIN_LED2 PIN_LED_RXL #define PIN_LED3 PIN_LED_TXL #define LED_BUILTIN 13 /* * SPI Interfaces */ #define SPI_INTERFACES_COUNT 1 #define SPI_INTERFACE SPI0 #define SPI_INTERFACE_ID ID_SPI0 #define SPI_CHANNELS_NUM 4 #define PIN_SPI_SS0 (77U) #define PIN_SPI_SS1 (87U) #define PIN_SPI_SS2 (86U) #define PIN_SPI_SS3 (78U) #define PIN_SPI_MOSI (75U) #define PIN_SPI_MISO (74U) #define PIN_SPI_SCK (76U) #define BOARD_SPI_SS0 (77U) //(10U) #define BOARD_SPI_SS1 (4U) #define BOARD_SPI_SS2 (52U) #define BOARD_SPI_SS3 PIN_SPI_SS3 #define BOARD_SPI_DEFAULT_SS BOARD_SPI_SS3 #define BOARD_PIN_TO_SPI_PIN(x) \ (x==BOARD_SPI_SS0 ? PIN_SPI_SS0 : \ (x==BOARD_SPI_SS1 ? PIN_SPI_SS1 : \ (x==BOARD_SPI_SS2 ? PIN_SPI_SS2 : PIN_SPI_SS3 ))) #define BOARD_PIN_TO_SPI_CHANNEL(x) \ (x==BOARD_SPI_SS0 ? 0 : \ (x==BOARD_SPI_SS1 ? 1 : \ (x==BOARD_SPI_SS2 ? 2 : 3))) static const uint8_t SS = BOARD_SPI_SS0; static const uint8_t SS1 = BOARD_SPI_SS1; static const uint8_t SS2 = BOARD_SPI_SS2; static const uint8_t SS3 = BOARD_SPI_SS3; static const uint8_t MOSI = PIN_SPI_MOSI; static const uint8_t MISO = PIN_SPI_MISO; static const uint8_t SCK = PIN_SPI_SCK; /* * Wire Interfaces */ #define WIRE_INTERFACES_COUNT 2 #define PIN_WIRE_SDA (20U) #define PIN_WIRE_SCL (21U) #define WIRE_INTERFACE TWI1 #define WIRE_INTERFACE_ID ID_TWI1 #define WIRE_ISR_HANDLER TWI1_Handler #define WIRE_ISR_ID TWI1_IRQn #define PIN_WIRE1_SDA (70U) #define PIN_WIRE1_SCL (71U) #define WIRE1_INTERFACE TWI0 #define WIRE1_INTERFACE_ID ID_TWI0 #define WIRE1_ISR_HANDLER TWI0_Handler #define WIRE1_ISR_ID TWI0_IRQn static const uint8_t SDA = PIN_WIRE_SDA; static const uint8_t SCL = PIN_WIRE_SCL; static const uint8_t SDA1 = PIN_WIRE1_SDA; static const uint8_t SCL1 = PIN_WIRE1_SCL; /* * UART/USART Interfaces */ // Serial #define PINS_UART (81U) // Serial1 #define PINS_USART0 (82U) // Serial2 #define PINS_USART1 (83U) // Serial3 #define PINS_USART3 (84U) /* * USB Interfaces */ #define PINS_USB (85U) /* * Analog pins */ static const uint8_t A0 = 54; static const uint8_t A1 = 55; static const uint8_t A2 = 56; static const uint8_t A3 = 57; static const uint8_t A4 = 58; static const uint8_t A5 = 59; static const uint8_t A6 = 60; static const uint8_t A7 = 61; static const uint8_t A8 = 62; static const uint8_t A9 = 63; static const uint8_t A10 = 64; static const uint8_t A11 = 65; static const uint8_t DAC0 = 66; static const uint8_t DAC1 = 67; static const uint8_t CANRX = 68; static const uint8_t CANTX = 69; #define ADC_RESOLUTION 12 /* * Complementary CAN pins */ static const uint8_t CAN1RX = 88; static const uint8_t CAN1TX = 89; // CAN0 #define PINS_CAN0 (90U) // CAN1 #define PINS_CAN1 (91U) /* * DACC */ #define DACC_INTERFACE DACC #define DACC_INTERFACE_ID ID_DACC #define DACC_RESOLUTION 12 #define DACC_ISR_HANDLER DACC_Handler #define DACC_ISR_ID DACC_IRQn /* * PWM */ #define PWM_INTERFACE PWM #define PWM_INTERFACE_ID ID_PWM #define PWM_FREQUENCY 31000 #define PWM_MAX_DUTY_CYCLE 255 #define PWM_MIN_DUTY_CYCLE 0 #define PWM_RESOLUTION 8 /* * TC */ #define TC_INTERFACE TC0 #define TC_INTERFACE_ID ID_TC0 #define TC_FREQUENCY 100000 #define TC_MAX_DUTY_CYCLE 255 #define TC_MIN_DUTY_CYCLE 0 #define TC_RESOLUTION 8 #ifdef __cplusplus } #endif /*---------------------------------------------------------------------------- * Arduino objects - C++ only *----------------------------------------------------------------------------*/ #ifdef __cplusplus extern UARTClass Serial; extern USARTClass Serial1; extern USARTClass Serial2; extern USARTClass Serial3; #endif // These serial port names are intended to allow libraries and architecture-neutral // sketches to automatically default to the correct port name for a particular type // of use. For example, a GPS module would normally connect to SERIAL_PORT_HARDWARE_OPEN, // the first hardware serial port whose RX/TX pins are not dedicated to another use. // // SERIAL_PORT_MONITOR Port which normally prints to the Arduino Serial Monitor // // SERIAL_PORT_USBVIRTUAL Port which is USB virtual serial // // SERIAL_PORT_LINUXBRIDGE Port which connects to a Linux system via Bridge library // // SERIAL_PORT_HARDWARE Hardware serial port, physical RX & TX pins. // // SERIAL_PORT_HARDWARE_OPEN Hardware serial ports which are open for use. Their RX & TX // pins are NOT connected to anything by default. #define SERIAL_PORT_MONITOR Serial #define SERIAL_PORT_USBVIRTUAL SerialUSB #define SERIAL_PORT_HARDWARE_OPEN Serial1 #define SERIAL_PORT_HARDWARE_OPEN1 Serial2 #define SERIAL_PORT_HARDWARE_OPEN2 Serial3 #define SERIAL_PORT_HARDWARE Serial #define SERIAL_PORT_HARDWARE1 Serial1 #define SERIAL_PORT_HARDWARE2 Serial2 #define SERIAL_PORT_HARDWARE3 Serial3 #endif /* _VARIANT_ARDUINO_DUE_X_ */