🩹 Fix Anycubic PlayTune (#25735)

Followup to #25690

Co-authored-by: Scott Lahteine <thinkyhead@users.noreply.github.com>

Marlin/src/lcd/extui/anycubic/Tunes.cpp

@@ -39,12 +39,12 @@
 
 namespace Anycubic {
 
-  void PlayTune(const uint16_t *tune, const uint8_t speed=1) {
+  void PlayTune(const uint16_t *tune, const uint8_t speed/*=1*/) {
     const uint16_t wholenotelen = tune[0] / speed;
     for (uint8_t pos = 1; pos < MAX_TUNE_LENGTH; pos += 2) {
       const uint16_t freq = tune[pos];
       if (freq == n_END) break;
-      BUZZ(freq, wholenotelen / tune[pos + 1]);
+      BUZZ(wholenotelen / tune[pos + 1], freq);
     }
   }
 

Marlin/src/lcd/extui/anycubic/Tunes.h

@@ -61,7 +61,7 @@ n_END=10000 // end of tune marker
 
 namespace Anycubic {
 
-  void PlayTune(const uint16_t *tune, const uint8_t speed);
+  void PlayTune(const uint16_t *tune, const uint8_t speed=1);
 
   // Only uncomment the tunes you are using to save memory
   // This will help you write tunes!
@@ -100,7 +100,7 @@ namespace Anycubic {
     n_END
   };
 
-  const uint16_t Heater_Timedout[] = {
+  const uint16_t HeaterTimeout[] = {
     1000,
     n_C6,l_T1,
     n_END

Marlin/src/lcd/extui/anycubic_chiron/chiron_tft.cpp

@@ -104,7 +104,7 @@ void ChironTFT::Startup() {
   injectCommands(AC_cmnd_enable_leveling);
 
   // Startup tunes are defined in Tunes.h
-  PlayTune(TERN(AC_DEFAULT_STARTUP_TUNE, Anycubic_PowerOn, GB_PowerOn), 1);
+  PlayTune(TERN(AC_DEFAULT_STARTUP_TUNE, Anycubic_PowerOn, GB_PowerOn));
 
   #if ACDEBUGLEVEL
     SERIAL_ECHOLNPGM("AC Debug Level ", ACDEBUGLEVEL);
@@ -192,7 +192,7 @@ void ChironTFT::FilamentRunout()  {
   // 1 Signal filament out
   last_error = AC_error_filament_runout;
   SendtoTFTLN(isPrintingFromMedia() ? AC_msg_filament_out_alert : AC_msg_filament_out_block);
-  PlayTune(FilamentOut, 1);
+  PlayTune(FilamentOut);
 }
 
 void ChironTFT::ConfirmationRequest(const char * const msg)  {
@@ -215,7 +215,7 @@ void ChironTFT::ConfirmationRequest(const char * const msg)  {
       if (strcmp_P(msg, MARLIN_msg_heater_timeout) == 0) {
         pause_state = AC_paused_heater_timed_out;
         SendtoTFTLN(AC_msg_paused); // enable continue button
-        PlayTune(BEEPER_PIN,Heater_Timedout,1);
+        PlayTune(HeaterTimeout);
       }
       // Reheat finished, send acknowledgement
       else if (strcmp_P(msg, MARLIN_msg_reheat_done) == 0) {
@@ -253,7 +253,7 @@ void ChironTFT::StatusChange(const char * const msg)  {
       }
       // If probing fails don't save the mesh raise the probe above the bad point
       if (strcmp_P(msg, MARLIN_msg_probing_failed) == 0) {
-        PlayTune(BeepBeepBeeep, 1);
+        PlayTune(BeepBeepBeeep);
         injectCommands(F("G1 Z50 F500"));
         SendtoTFTLN(AC_msg_probing_complete);
         printer_state = AC_printer_idle;
@@ -307,7 +307,7 @@ void ChironTFT::StatusChange(const char * const msg)  {
 void ChironTFT::PowerLossRecovery()  {
   printer_state = AC_printer_resuming_from_power_outage; // Play tune to notify user we can recover.
   last_error = AC_error_powerloss;
-  PlayTune(SOS, 1);
+  PlayTune(SOS);
   SERIAL_ECHOLNF(AC_msg_powerloss_recovery);
 }
 

Marlin/src/lcd/extui/anycubic_vyper/dgus_tft.cpp

@@ -463,7 +463,7 @@ namespace Anycubic {
       pop_up_index = 15;  // show filament lack.
 
       if (READ(FIL_RUNOUT_PIN) == FIL_RUNOUT_STATE) {
-        PlayTune(FilamentOut, 1);
+        PlayTune(FilamentOut);
 
         feedrate_back = getFeedrate_percent();
 
@@ -505,7 +505,7 @@ namespace Anycubic {
         if (strcmp_P(msg, MARLIN_msg_heater_timeout) == 0) {
           pause_state = AC_paused_heater_timed_out;
           SendtoTFTLN(AC_msg_paused); // enable continue button
-          PlayTune(Heater_Timedout, 1);
+          PlayTune(HeaterTimeout);
         }
         // Reheat finished, send acknowledgement
         else if (strcmp_P(msg, MARLIN_msg_reheat_done) == 0) {
@@ -576,7 +576,7 @@ namespace Anycubic {
 
           // If probing fails don't save the mesh raise the probe above the bad point
           if (strcmp_P(msg, MARLIN_msg_probing_failed) == 0) {
-            PlayTune(BeepBeepBeeep, 1);
+            PlayTune(BeepBeepBeeep);
             injectCommands(F("G1 Z50 F500"));
             ChangePageOfTFT(PAGE_CHS_ABNORMAL_LEVELING_SENSOR);
             SendtoTFTLN(AC_msg_probing_complete);
@@ -1070,7 +1070,7 @@ namespace Anycubic {
                 #else
                   SendTxtToTFT(recovery.info.sd_filename, TXT_OUTAGE_RECOVERY_FILE);
                 #endif
-                PlayTune(SOS, 1);
+                PlayTune(SOS);
               }
             #else
               constexpr bool is_outage = false;
@@ -1081,7 +1081,7 @@ namespace Anycubic {
           }
           else if (control_value == 0x010000) {         // startup first gif
             // Startup tunes are defined in Tunes.h
-            PlayTune(Anycubic_PowerOn, 1);              // takes 3500 ms
+            PlayTune(Anycubic_PowerOn);                 // takes 3500 ms
           }
         }