🐛 Creality Free Runs fixups (#26562)

Followup to #25636, #26533

Co-authored-by: Scott Lahteine <thinkyhead@users.noreply.github.com>

Marlin/src/inc/Changes.h

@@ -669,6 +669,8 @@
   #error "Z_PROBE_OFFSET_RANGE_(MIN|MAX) is now PROBE_OFFSET_Z(MIN|MAX)."
 #elif defined(LARGE_MOVE_ITEMS)
   #error "LARGE_MOVE_ITEMS is obsolete. Instead define MANUAL_MOVE_DISTANCE_MM and MANUAL_MOVE_DISTANCE_IN."
+#elif defined(SDIO_SUPPORT)
+  #error "SDIO_SUPPORT is now ONBOARD_SDIO."
 #endif
 
 // L64xx stepper drivers have been removed

Marlin/src/inc/Warnings.cpp

@@ -811,3 +811,10 @@
 #if HAL_ADC_VREF_MV < 5000 && ANY_THERMISTOR_IS(-1) && DISABLED(ALLOW_AD595_3V3_VREF)
   #warning "The (-1) AD595 Thermocouple Amplifier requires 5V input supply! Use AD8495 for 3.3V ADC."
 #endif
+
+/**
+ * No PWM on the Piezo Beeper?
+ */
+#if PIN_EXISTS(BEEPER) && ALL(SPEAKER, NO_SPEAKER)
+  #warning "The BEEPER cannot produce tones so you can disable SPEAKER."
+#endif

Marlin/src/pins/mega/pins_GT2560_V3_A20.h

@@ -33,10 +33,6 @@
   #define LCD_PINS_D7                          6
 #endif
 
-#ifndef SPEAKER
-  #define SPEAKER                                 // The speaker can produce tones
-#endif
-
 #if IS_NEWPANEL
   #define BTN_EN1                             16
   #define BTN_EN2                             17

Marlin/src/pins/mega/pins_GT2560_V4_A20.h

@@ -35,10 +35,6 @@
   #define LCD_PINS_D7                          6
 #endif
 
-#ifndef SPEAKER
-  #define SPEAKER                                 // The speaker can produce tones
-#endif
-
 #if IS_NEWPANEL
   #define BTN_EN1                             16
   #define BTN_EN2                             17

Marlin/src/pins/samd/pins_BRICOLEMON_LITE_V1_0.h

@@ -228,7 +228,7 @@
 
     #ifndef BEEPER_PIN
       #define BEEPER_PIN             EXP1_01_PIN
-      #undef SPEAKER
+      #define NO_SPEAKER
     #endif
 
   #elif ENABLED(REPRAPWORLD_GRAPHICAL_LCD)

Marlin/src/pins/samd/pins_BRICOLEMON_V1_0.h

@@ -281,7 +281,7 @@
 
     #ifndef BEEPER_PIN
       #define BEEPER_PIN             EXP1_01_PIN
-      #undef SPEAKER
+      #define NO_SPEAKER
     #endif
 
   #elif ENABLED(REPRAPWORLD_GRAPHICAL_LCD)

Marlin/src/pins/stm32f4/pins_BLACKPILL_CUSTOM.h

@@ -114,7 +114,7 @@
 
 #define SD_DETECT_PIN                       -1
 #define SDCARD_CONNECTION                ONBOARD
-//#define SDIO_SUPPORT
+//#define ONBOARD_SDIO
 #define NO_SD_HOST_DRIVE                          // This board's SD is only seen by the printer
 
 #if SD_CONNECTION_IS(ONBOARD)

Marlin/src/pins/stm32f4/pins_CREALITY_CR4NTXXC10.h

@@ -100,15 +100,15 @@
 #define X_STEP_PIN                          PC2
 #define X_DIR_PIN                           PB9
 
-#define Y_ENABLE_PIN               X_ENABLE_PIN
+#define Y_ENABLE_PIN                X_ENABLE_PIN
 #define Y_STEP_PIN                          PB8
 #define Y_DIR_PIN                           PB7
 
-#define Z_ENABLE_PIN               X_ENABLE_PIN
+#define Z_ENABLE_PIN                X_ENABLE_PIN
 #define Z_STEP_PIN                          PB6
 #define Z_DIR_PIN                           PB5
 
-#define E0_ENABLE_PIN              X_ENABLE_PIN
+#define E0_ENABLE_PIN               X_ENABLE_PIN
 #define E0_STEP_PIN                         PB4
 #define E0_DIR_PIN                          PB3
 
@@ -188,74 +188,55 @@
 //
 #define SD_DETECT_PIN                       PC1
 #define SDCARD_CONNECTION                ONBOARD
-#define ONBOARD_SPI_DEVICE                     1
-//#define ONBOARD_SD_CS_PIN                 PA4   // SDSS
-#define SDIO_SUPPORT
+#define ONBOARD_SDIO
+#define SDIO_CLOCK                       4500000
+#define SDIO_READ_RETRIES                     16
 #define NO_SD_HOST_DRIVE                  // This board's SD is only seen by the printer
 
-#if ENABLED(CR10_STOCKDISPLAY)
-
-  #if ENABLED(RET6_12864_LCD)
-    // RET6 12864 LCD
-    #define LCD_PINS_RS                     PB12
-    #define LCD_PINS_EN                     PB15
-    #define LCD_PINS_D4                     PB13
-
-    #define BTN_ENC                         PB2
-    #define BTN_EN1                         PA2
-    #define BTN_EN2                         PB14
+/**
+ *                 ------
+ *            PC0 | 1  2 | PB2
+ *       TX2  PA2 | 3  4 | PA3  RX2
+ * SPI2_MISO PB14 | 5  6 | PB13 SPI2_SCK
+ * SPI2_NSS  PB12 | 7  8 | PB15 SPI2_MOSI
+ *            GND | 9 10 | 5V
+ *                 ------
+ *                  EXP1
+ */
+#define EXP1_01_PIN                         PC0
+#define EXP1_02_PIN                         PB2
+#define EXP1_03_PIN                         PA2
+#define EXP1_04_PIN                         PA3
+#define EXP1_05_PIN                         PB14
+#define EXP1_06_PIN                         PB13
+#define EXP1_07_PIN                         PB12
+#define EXP1_08_PIN                         PB15
 
-    #ifndef HAS_PIN_27_BOARD
-      #define BEEPER_PIN                    PC0
-    #endif
+#if ENABLED(CR10_STOCKDISPLAY)
 
-  #elif ENABLED(VET6_12864_LCD)
-    // VET6 12864 LCD
-    #define LCD_PINS_RS                     PA4
-    //#define LCD_PINS_EN                   PA7
-    #define LCD_PINS_D4                     PA5
+  #define LCD_PINS_RS                EXP1_07_PIN
+  #define LCD_PINS_EN                EXP1_08_PIN
+  #define LCD_PINS_D4                EXP1_06_PIN
 
-    #define BTN_ENC                         PC5
-    #define BTN_EN1                         PB10
-    #define BTN_EN2                         PA6
+  #define BTN_ENC                    EXP1_02_PIN
+  #define BTN_EN1                    EXP1_03_PIN
+  #define BTN_EN2                    EXP1_05_PIN
 
-  #else
-    #error "Define RET6_12864_LCD or VET6_12864_LCD to select pins for CR10_STOCKDISPLAY with the CREALITY_CR4NTXXC10 controller."
+  #ifndef HAS_PIN_27_BOARD
+    #define BEEPER_PIN               EXP1_01_PIN
   #endif
 
 #elif ENABLED(DWIN_CREALITY_LCD)
 
-  // RET6 DWIN ENCODER LCD
-  #define BTN_ENC                           PB14
-  #define BTN_EN1                           PB15
-  #define BTN_EN2                           PB12
+  // DWIN ENCODER LCD
+  #define BTN_ENC                    EXP1_05_PIN
+  #define BTN_EN1                    EXP1_08_PIN
+  #define BTN_EN2                    EXP1_07_PIN
 
-  //#define LCD_LED_PIN                     PB2
+  //#define LCD_LED_PIN              EXP1_02_PIN
   #ifndef BEEPER_PIN
-    #define BEEPER_PIN                      PB13
-    #undef SPEAKER
+    #define BEEPER_PIN               EXP1_06_PIN
+    #define NO_SPEAKER
   #endif
 
-#elif ENABLED(DWIN_VET6_CREALITY_LCD)
-
-  // VET6 DWIN ENCODER LCD
-  #define BTN_ENC                           PA6
-  //#define BTN_EN1                         PA7
-  #define BTN_EN2                           PA4
-
-  #define BEEPER_PIN                        PA5
-
-#endif
-
-//
-// M3/M4/M5 - Spindle/Laser Control
-//
-#if HAS_CUTTER
-  //#undef HEATER_0_PIN
-  //#undef HEATER_BED_PIN
-  //#undef FAN0_PIN
-  #define SPINDLE_LASER_ENA_PIN             PC0   // FET 1
-  #define SPINDLE_LASER_PWM_PIN             PC0   // Bed FET
-  #define SPINDLE_DIR_PIN                   PC0   // FET 4
-  //#define LASER_SOFT_PWM_PIN              PC0
 #endif

Marlin/src/pins/stm32f4/pins_CREALITY_F401.h

@@ -125,7 +125,7 @@
 #define SDCARD_CONNECTION               ONBOARD
 #define ONBOARD_SPI_DEVICE                     1
 #define ONBOARD_SD_CS_PIN                   PC12  // SDSS
-#define SDIO_SUPPORT
+#define ONBOARD_SDIO
 #define NO_SD_HOST_DRIVE                          // This board's SD is only seen by the printer
 
 // SPI 2

ini/stm32f4.ini

@@ -742,17 +742,14 @@ upload_protocol = stlink
 #
 [env:STM32F401RE_freeruns]
 extends                     = stm32_variant
-board                       = genericSTM32F401RE
-board_build.variant         = marlin_STM32F401RE_freeruns
+board                       = marlin_STM32F401RE_freeruns
 board_build.offset          = 0x10000
 board_upload.offset_address = 0x08010000
 board_build.rename          = firmware-{date}-{time}.bin
-build_flags                 = ${stm32_variant.build_flags} -DMCU_STM32F401RE -DSTM32F4
+build_flags                 = ${stm32_variant.build_flags} -DSTM32F401xE
                               -DSS_TIMER=4 -DTIMER_SERVO=TIM5
                               -DTRANSFER_CLOCK_DIV=8
 build_unflags               = ${stm32_variant.build_unflags} -DUSBCON -DUSBD_USE_CDC
-extra_scripts               = ${stm32_variant.extra_scripts}
-                              pre:buildroot/share/PlatformIO/scripts/random-bin.py
 monitor_speed               = 115200
 
 [env:STM32F401RE_freeruns_jlink]