#note: all settings are id$0 as the slicer consider there is only one value in the arrays in the gui.
page:Filament:spool
group:filament_spool_weight_event:Filament
	setting:id$0:filament_colour
	setting:id$0:filament_diameter
	setting:id$0:filament_density
	setting:id$0:filament_cost
	setting:id$0:filament_spool_weight
group:Flow
	setting:id$0:extrusion_multiplier
	setting:id$0:filament_fill_top_flow_ratio
	setting:id$0:filament_first_layer_flow_ratio
group:Temperature °C
	line:Extruder
		setting:id$0:first_layer_temperature
		setting:id$0:temperature
	end_line
	line:Bed
		setting:id$0:first_layer_bed_temperature
		setting:id$0:label$Other layers:bed_temperature
	end_line
	setting:id$0:chamber_temperature
	setting:id$0:label$Idle:idle_temperature
group:Filament properties
	setting:id$0:width$7:filament_type
	setting:id$0:filament_soluble
	setting:id$0:filament_shrink
	setting:id$0:filament_max_overlap
	setting:id$0:filament_pressure_advance
group:Print speed override
	setting:id$0:filament_max_speed
	setting:id$0:filament_max_volumetric_speed
	volumetric_speed_description

page:Cooling:time
group:Fan speed - default
	setting:id$0:default_fan_speed
	line:Perimeter fan speed
		setting:id$0:label_width$12:label$Internal:perimeter_fan_speed
		setting:id$0:label_width$12:label$External:external_perimeter_fan_speed
	line:Internal Infill fan speed
		setting:id$0:label_width$12:label$Sparse:infill_fan_speed
	line:Solid Infill fan speed
		setting:id$0:label_width$12:label$Solid:solid_infill_fan_speed
		setting:id$0:label_width$12:label$Top solid:top_fan_speed
	line:Support Material fan speed
		setting:id$0:label_width$12:label$Default:support_material_fan_speed
		setting:id$0:label_width$12:label$Interface:support_material_interface_fan_speed
	line:Bridges fan speed
		setting:id$0:label_width$12:label$Bridges:bridge_fan_speed
		setting:id$0:label_width$12:label$Internal bridges:internal_bridge_fan_speed
	line:Overhangs Perimeter fan speed
		setting:id$0:label_width$12:label$Overhangs:overhangs_fan_speed
        setting:id$0:overhangs_dynamic_fan_speed
	line:Gap fill fan speed
		setting:id$0:label_width$12:label$Gap fill:gap_fill_fan_speed
	line:Disable fan for the first
		setting:id$0:width$5:label$_:sidetext_width$7:disable_fan_first_layers
		setting:id$0:width$5:label_width$18:full_fan_speed_layer
	end_line
group:Short layer time - began to increase base fan speed
	setting:id$0:fan_below_layer_time
	setting:id$0:label$Max fan speed:max_fan_speed
group:Very short layer time - began to decrease extrusion rate
	setting:id$0:label$Layer time goal:slowdown_below_layer_time
	setting:id$0:width$4:max_speed_reduction
	setting:id$0:width$4:min_print_speed
group:Behavior
	cooling_description

page:Multimaterial:funnel
group:Multimaterial toolchange temperature 
	setting:id$0:filament_enable_toolchange_temp
	setting:id$0:filament_toolchange_temp 
	setting:id$0:filament_use_fast_skinnydip
	setting:id$0:filament_enable_toolchange_part_fan
	setting:id$0:filament_toolchange_part_fan_speed
group:Multimaterial toolchange string reduction
	setting:id$0:filament_use_skinnydip 
	setting:id$0:filament_skinnydip_distance
	setting:id$0:filament_melt_zone_pause 
	setting:id$0:filament_cooling_zone_pause
	setting:id$0:filament_dip_insertion_speed
	setting:id$0:filament_dip_extraction_speed
group:Wipe tower parameters
	setting:id$0:filament_minimal_purge_on_wipe_tower
	setting:id$0:filament_max_wipe_tower_speed
group:Toolchange parameters with single extruder MM printers
	setting:id$0:filament_loading_speed_start
	setting:id$0:filament_loading_speed
	setting:id$0:filament_unloading_speed_start
	setting:id$0:filament_unloading_speed
	setting:id$0:filament_load_time
	setting:id$0:filament_unload_time
	setting:id$0:filament_toolchange_delay
	setting:id$0:filament_cooling_moves
	setting:id$0:filament_cooling_initial_speed
	setting:id$0:filament_cooling_final_speed
	setting:id$0:filament_wipe_advanced_pigment
	filament_ramming_parameters
group:Toolchange parameters with multi extruder MM printers
    setting:id$0:filament_multitool_ramming
    setting:id$0:filament_multitool_ramming_volume
    setting:id$0:filament_multitool_ramming_flow

filament_overrides_page

page:Custom G-code:cog
group:no_title:edit_gcode:validate_gcode:Start G-code
	setting:is_gcode:id$0:full_width:height$35:start_filament_gcode
group:no_title:edit_gcode:validate_gcode:End G-code
	setting:is_gcode:id$0:full_width:height$35:end_filament_gcode

page:Notes:note
group:label_width$0:Notes
	setting:id$0:full_width:height$25:filament_notes
group:label_width$0:Custom variables
	setting:id$0:full_width:height$15:filament_custom_variables

page:Dependencies:wrench
	group:Profile dependencies
	setting:id$0:compatible_printers
	setting:id$0:full_width:color:compatible_printers_condition
	setting:id$0:compatible_prints
	setting:id$0:full_width:color:compatible_prints_condition
	parent_preset_description