BigTreeTech BTT002/TMC2209 Config for Průša MK3S

Requirements

Průša MK3S, MK3S+, or MK3 with MK3S/MK3S+ upgrade is required for filament runout to work properly.
BigTreeTech BTT002 motherboard
4 x BigTreeTech TMC2209s (DIAG pin location differs from Watterott's & similar designs)

Configuration Options

Flags specific to this printer/configuration:

MK3_FAN_PINS - Disable this for FAN_PIN PB9 and FAN1_PIN PB8
GEARBOX_BEAR - Is printer equipped with a 3.5:1 gearbox on the extruder?
TALLBEAR - Tall Bear (320mm)?
SUPERPINDA - SuperPinda present?

Upgrade Notes

⚠️ Cut or desolder the Z & E driver DIAG pins or they will interfere with PINDA & filament runout detection. ⚠️
Set the jumpers under your drivers to "TMC2208-UART MODE":

Changes to Start G-code

The W in Průša's G28 W ; home all without mesh bed level default G-code does not exist in Marlin and G80 ; mesh bed leveling cancels the current motion mode, so no bed leveling will take place.

Below are some example start G-code scripts from popular slicers to get you started.

PrusaSlicer

Set your G-code flavor to "Marlin 2" under "Printer Settings" -> "General" -> "Firmware" -> "G-code flavor".
Use the "Custom G-code" section under "Filament Settings" to add the Linear Advance (M900 K0.0) value since it can be saved on a per-filament basis.

Paste the start G-code block below in the "Custom G-code" section under "Printer Settings".

G90 ; use absolute coordinates
M83 ; extruder relative mode
M104 S170 ; preheat hotend to 170
M140 S[first_layer_bed_temperature] ; set bed temp
M190 S[first_layer_bed_temperature] ; wait for bed temp
G28 ; home all
G29 ; mesh bed leveling
G1 X0 Z0.6 Y-3.0 F1000.0 ; go outside print area for intro line
M104 S[first_layer_temperature] ; set hotend temp
M109 S[first_layer_temperature] ; wait for hotend temp
G92 E0.0
G1 X60.0 E9.0 F1000.0 ; intro line
G1 X100.0 E12.5 F1000.0 ; intro line
G92 E0.0

Cura

Paste the start G-code block below in the "Start G-code" section. Add your Linear Advance (M900 K0.0) value in the start G-code block below:

G90 ; use absolute coordinates
M83 ; extruder relative mode
M900 K0.0 ; place your linear advance value here
M104 S170 ; preheat hotend to 170
M140 S{material_bed_temperature_layer_0} ; set bed temp
M190 S{material_bed_temperature_layer_0} ; wait for bed temp
G28 ; home all
G29 ; mesh bed leveling
G1 X0 Z0.6 Y-3.0 F1000.0 ; go outside print area for intro line
M104 S{material_print_temperature_layer_0} ; set hotend temp
M109 S{material_print_temperature_layer_0} ; wait for hotend temp
G92 E0.0
G1 X60.0 E9.0 F1000.0 ; intro line
G1 X100.0 E12.5 F1000.0 ; intro line
G92 E0.0

IdeaMaker

Paste the start G-code block below in the filament's "Start G-code" section. Add your Linear Advance (M900 K0.0) value in the start G-code block below:

G90 ; use absolute coordinates
M83 ; extruder relative mode
M900 K0.0 ; place your linear advance value here
M104 S170 ; preheat hotend to 170
M140 S{temperature_heatbed} ; set bed temp
M190 S{temperature_heatbed} ; wait for bed temp
G28 ; home all
G29 ; mesh bed leveling
G1 X0 Z0.6 Y-3.0 F1000.0 ; go outside print area for intro line
M104 S{temperature_extruder1} ; set hotend temp
M109 S{temperature_extruder1} ; wait for hotend temp
G92 E0.0
G1 X60.0 E9.0 F1000.0 ; intro line
G1 X100.0 E12.5 F1000.0 ; intro line
G92 E0.0

Simplify3D

Paste the start G-code block below in the "Starting Script" section. Add your Linear Advance (M900 K0.0) value in the start G-code block below:

G90 ; use absolute coordinates
M83 ; extruder relative mode
M900 K0.0 ; place your linear advance value here
M104 S170 ; preheat hotend to 170
M140 S[bed0_temperature] ; set bed temp
M190 S[bed0_temperature] ; wait for bed temp
G28 ; home all
G29 ; mesh bed leveling
G1 X0 Z0.6 Y-3.0 F1000.0 ; go outside print area for intro line
M104 S[extruder0_temperature] T0 ; set hotend temp
M109 S[extruder0_temperature] T0 ; wait for hotend temp
G92 E0.0
G1 X60.0 E9.0 F1000.0 ; intro line
G1 X100.0 E12.5 F1000.0 ; intro line
G92 E0.0

README.md 4.5 KB History Raw