Cura/resources/definitions/fusedform_doppia_base.def.json

{
    "version": 2,
    "name": "fusedform_doppia_base",
    "inherits": "fusedform_base",
    "metadata":
    {
        "visible": false,
        "author": "Juan Blanco",
        "manufacturer": "Fused Form",
        "exclude_materials": [ "structur3d_dap100silicone" ],
        "has_machine_quality": true,
        "has_materials": true,
        "machine_extruder_trains":
        {
            "0": "fusedform_doppia_base_extruder_0",
            "1": "fusedform_doppia_base_extruder_1"
        },
        "preferred_material": "generic_pla",
        "preferred_quality_type": "normal"
    },
    "overrides":
    {
        "adhesion_type": { "default_value": "skirt" },
        "cool_fan_enabled": { "default_value": true },
        "cool_fan_full_at_height": { "value": 0.4 },
        "cool_fan_full_layer": { "value": 2 },
        "cool_min_speed": { "value": 30 },
        "gantry_height": { "value": "70" },
        "infill_overlap": { "value": 0 },
        "infill_sparse_density": { "value": 15 },
        "layer_height": { "default_value": 0.15 },
        "layer_height_0": { "default_value": 0.2 },
        "machine_center_is_zero": { "default_value": false },
        "machine_end_gcode": { "value": "'M104 S0 ;extruder heater off' + ('\\nM140 S0 ;heated bed heater off' if machine_heated_bed else '') + '\\nG91 ;relative positioning\\nG1 E-1 F300  ;retract the filament a bit before lifting the nozzle, to release some of the pressure\\nG28 X0 Y0 ;move X/Y to min endstops, so the head is out of the way\\nM84 ;steppers off\\nG90 ;absolute positioning\\nM107 ; Fans off'" },
        "machine_gcode_flavor": { "default_value": "RepRap (Marlin/Sprinter)" },
        "machine_head_with_fans_polygon":
        {
            "default_value": [
                [-20, 20],
                [-20, -20],
                [18, 20],
                [18, -18]
            ]
        },
        "machine_heated_bed": { "default_value": true },
        "machine_start_gcode": { "default_value": "G21 ;metric values\nG90 ;absolute positioning\nM82 ;set extruder to absolute mode\nM107 ;start with the fan off\nG28 X0 Y0 ;move X/Y to min endstops\nG28 Z0 ;move Z to min endstops\nG1 Z15.0 F9000 ;move the platform down 15mm\nG92 E0 ;zero the extruded length\nG1 F200 E6 ;extrude 6 mm of feed stock\nG92 E0 ;zero the extruded length again\n;Put printing message on LCD screen\nM117 Printing..." },
        "machine_use_extruder_offset_to_offset_coords": { "default_value": true },
        "optimize_wall_printing_order": { "value": true },
        "retraction_amount": { "default_value": 4 },
        "retraction_count_max": { "default_value": 10 },
        "retraction_enable": { "default_value": true },
        "retraction_extrusion_window": { "value": 4 },
        "retraction_hop": { "default_value": 0.2 },
        "retraction_hop_enabled": { "value": true },
        "retraction_min_travel": { "value": 5 },
        "retraction_speed": { "default_value": 70 },
        "speed_infill": { "value": 45 },
        "speed_print": { "value": 45 },
        "speed_topbottom": { "value": 40 },
        "speed_travel": { "value": 75 },
        "speed_wall": { "value": 35 },
        "speed_wall_x": { "value": 40 },
        "speed_z_hop": { "value": 2.5 },
        "support_angle": { "default_value": 50 },
        "support_brim_enable": { "value": true },
        "support_enable": { "value": true },
        "support_infill_angles":
        {
            "value": [
                -45
            ]
        },
        "support_interface_density": { "value": 70 },
        "support_interface_enable": { "value": true },
        "support_interface_height": { "value": 0.5 },
        "support_interface_pattern": { "default_value": "lines" },
        "support_pattern": { "default_value": "lines" },
        "support_xy_distance": { "value": 0.5 },
        "support_z_distance": { "value": 0.3 },
        "switch_extruder_retraction_amount": { "value": 6 },
        "switch_extruder_retraction_speeds": { "value": 60 },
        "top_bottom_thickness": { "value": 1.5 },
        "wall_line_count": { "value": 3 },
        "wall_thickness": { "value": 1.2 }
    }
}