Cura/resources/quality/nwa3d_a5/nwa3d_a5_normal.inst.cfg

[general]
version = 4
name = Normal Quality
definition = nwa3d_a5

[metadata]
setting_version = 6
type = quality
quality_type = normal
weight = 0
global_quality = True

[values]
layer_height = 0.15
initial_layer_height = 0.25
line_width = 0.4
initial_layer_line_width = 100
wall_thickness = 0.8
outer_wall_wipe_distance = 0.2
top_surface_skin_layers = 1
top_bottom_thickness = 0.6
top_thickness = 0.8
top_layers = 5
bottom_thickness = 0.6
bottom_layers = 3
top_bottom_pattern = lines
bottom_pattern_initial_layer = lines
outer_wall_inset = 0
optimize_wall_printing_order = false
outer_before_inner_walls = false
alternate_extra_wall = false
compensate_wall_overlaps = true
compensate_outer_wall_overlaps = true
compensate_inner_wall_overlaps = true
minimum_wall_flow = 0
fill_gaps_between_walls = everywhere
filter_out_tiny_gaps = true
print_thin_walls = true
horizontal_expansion = 0
ignore_small_z_gaps = true
extra_skin_wall_count = 1
enable_ironing = false
infill_density = 20
connect_infill_lines = false
infill_line_multiplier = 1
extra_infill_wall_count = 0
infill_overlap_percentage = 10
skin_overlap_percentage = 5
infill_wipe_distance = 0.1
gradual_infill_steps = 0
infill_before_walls = false
infill_support = false
maximum_skin_angle_for_expansion = 90
material_diameter = 1.75
default_printing_temperature = 220
initial_printing_temperature = 220
final_printing_temperature = 220
default_build_plate_temperature = 0
build_plate_temperature = 0
flow = 100
enable_retraction = true
retract_at_layer_change = false
retraction_distance = 5
retraction_speed = 45
retraction_extra_prime_amount = 0
retraction_minimum_travel = 0.8
maximum_retraction_count = 90
minimum_extrusion_distance_window = 5
limit_support_retractions = true
nozzle_switch_retraction_distance = 16
nozzle_switch_retraction_speed = 20
print_speed = 50
travel_speed = 150
initial_layer_speed = 10
initial_layer_travel_speed = 50
maximum_z_speed = 0
number_of_slower_layers = 2
equalize_filament_flow = false
enable_acceleration_control = false
enable_jerk_control = false
combing_mode = off
retract_before_outer_wall = false
z_hop_when_retracted = false
enable_print_cooling = true
fan_speed = 100
initial_fan_speed = 0
regular_fan_speed_at_height = 0.25
regular_fan_speed_at_layer = 2
lift_head = false
generate_support = true
support_placement = everywhere
support_overhang_angle = 50
support_pattern = grid
support_wall_line_count = 0
connect_support_lines = false
support_density = 20
support_infill_line_direction = 0
enable_support_brim = true
support_brim_line_count = 5
support_z_distance = 0.2
support_x_y_distance = 0.7
minimum_support_x_y_distance = 0.2
support_stair_step_height = 0.3
support_stair_step_maximum_width = 5.0
support_join_distance = 2.0
support_horizontal_expansion = 0.2
gradual_support_infill_steps = 0
enable_support_roof = true
enable_support_floor = false
support_roof_thickness = 0.45
support_roof_density = 45
support_roof_pattern = lines
fan_speed_override = false
use_towers = true
tower_diameter = 3
tower_roof_angle = 65
build_plate_adhesion_type = skirt
skirt_line_count = 2
skirt_distance = 3
union_overlapping_volumes = true
remove_all_holes = false
extensive_stiching = false
keep_disconnected_faces = false
merged_meshes_overlap = 0.15
remove_mesh_intersection = false