Cura/resources/i18n/en/fdmprinter.json.po

msgid ""
msgstr ""
"Project-Id-Version: Uranium json setting files\n"
"Report-Msgid-Bugs-To: http://github.com/ultimaker/uranium\n"
"POT-Creation-Date: 2016-01-13 13:43+0000\n"
"PO-Revision-Date: 2016-01-13 13:43+0000\n"
"Last-Translator: Automatically generated\n"
"Language-Team: none\n"
"MIME-Version: 1.0\n"
"Content-Type: text/plain; charset=UTF-8\n"
"Content-Transfer-Encoding: 8bit\n"
"Language: en\n"
"Plural-Forms: nplurals=2; plural=(n != 1);\n"

#: fdmprinter.json
msgctxt "machine label"
msgid "Machine"
msgstr "Machine"

#: fdmprinter.json
msgctxt "machine_nozzle_size label"
msgid "Nozzle Diameter"
msgstr "Nozzle Diameter"

#: fdmprinter.json
msgctxt "machine_nozzle_size description"
msgid "The inner diameter of the nozzle."
msgstr "The inner diameter of the nozzle."

#: fdmprinter.json
msgctxt "resolution label"
msgid "Quality"
msgstr "Quality"

#: fdmprinter.json
msgctxt "layer_height label"
msgid "Layer Height"
msgstr "Layer Height"

#: fdmprinter.json
msgctxt "layer_height description"
msgid ""
"The height of each layer, in mm. Normal quality prints are 0.1mm, high "
"quality is 0.06mm. You can go up to 0.25mm with an Ultimaker for very fast "
"prints at low quality. For most purposes, layer heights between 0.1 and "
"0.2mm give a good tradeoff of speed and surface finish."
msgstr ""
"The height of each layer, in mm. Normal quality prints are 0.1mm, high "
"quality is 0.06mm. You can go up to 0.25mm with an Ultimaker for very fast "
"prints at low quality. For most purposes, layer heights between 0.1 and "
"0.2mm give a good tradeoff of speed and surface finish."

#: fdmprinter.json
msgctxt "layer_height_0 label"
msgid "Initial Layer Height"
msgstr "Initial Layer Height"

#: fdmprinter.json
msgctxt "layer_height_0 description"
msgid ""
"The layer height of the bottom layer. A thicker bottom layer makes sticking "
"to the bed easier."
msgstr ""
"The layer height of the bottom layer. A thicker bottom layer makes sticking "
"to the bed easier."

#: fdmprinter.json
msgctxt "line_width label"
msgid "Line Width"
msgstr "Line Width"

#: fdmprinter.json
msgctxt "line_width description"
msgid ""
"Width of a single line. Each line will be printed with this width in mind. "
"Generally the width of each line should correspond to the width of your "
"nozzle, but for the outer wall and top/bottom surface smaller line widths "
"may be chosen, for higher quality."
msgstr ""
"Width of a single line. Each line will be printed with this width in mind. "
"Generally the width of each line should correspond to the width of your "
"nozzle, but for the outer wall and top/bottom surface smaller line widths "
"may be chosen, for higher quality."

#: fdmprinter.json
msgctxt "wall_line_width label"
msgid "Wall Line Width"
msgstr "Wall Line Width"

#: fdmprinter.json
msgctxt "wall_line_width description"
msgid ""
"Width of a single shell line. Each line of the shell will be printed with "
"this width in mind."
msgstr ""
"Width of a single shell line. Each line of the shell will be printed with "
"this width in mind."

#: fdmprinter.json
msgctxt "wall_line_width_0 label"
msgid "Outer Wall Line Width"
msgstr "Outer Wall Line Width"

#: fdmprinter.json
msgctxt "wall_line_width_0 description"
msgid ""
"Width of the outermost shell line. By printing a thinner outermost wall line "
"you can print higher details with a larger nozzle."
msgstr ""
"Width of the outermost shell line. By printing a thinner outermost wall line "
"you can print higher details with a larger nozzle."

#: fdmprinter.json
msgctxt "wall_line_width_x label"
msgid "Other Walls Line Width"
msgstr "Other Walls Line Width"

#: fdmprinter.json
msgctxt "wall_line_width_x description"
msgid ""
"Width of a single shell line for all shell lines except the outermost one."
msgstr ""
"Width of a single shell line for all shell lines except the outermost one."

#: fdmprinter.json
msgctxt "skirt_line_width label"
msgid "Skirt line width"
msgstr "Skirt line width"

#: fdmprinter.json
msgctxt "skirt_line_width description"
msgid "Width of a single skirt line."
msgstr "Width of a single skirt line."

#: fdmprinter.json
msgctxt "skin_line_width label"
msgid "Top/bottom line width"
msgstr "Top/bottom line width"

#: fdmprinter.json
msgctxt "skin_line_width description"
msgid ""
"Width of a single top/bottom printed line, used to fill up the top/bottom "
"areas of a print."
msgstr ""
"Width of a single top/bottom printed line, used to fill up the top/bottom "
"areas of a print."

#: fdmprinter.json
msgctxt "infill_line_width label"
msgid "Infill line width"
msgstr "Infill line width"

#: fdmprinter.json
msgctxt "infill_line_width description"
msgid "Width of the inner infill printed lines."
msgstr "Width of the inner infill printed lines."

#: fdmprinter.json
msgctxt "support_line_width label"
msgid "Support line width"
msgstr "Support line width"

#: fdmprinter.json
msgctxt "support_line_width description"
msgid "Width of the printed support structures lines."
msgstr "Width of the printed support structures lines."

#: fdmprinter.json
msgctxt "support_roof_line_width label"
msgid "Support Roof line width"
msgstr "Support Roof line width"

#: fdmprinter.json
msgctxt "support_roof_line_width description"
msgid ""
"Width of a single support roof line, used to fill the top of the support."
msgstr ""
"Width of a single support roof line, used to fill the top of the support."

#: fdmprinter.json
msgctxt "shell label"
msgid "Shell"
msgstr "Shell"

#: fdmprinter.json
msgctxt "shell_thickness label"
msgid "Shell Thickness"
msgstr "Shell Thickness"

#: fdmprinter.json
msgctxt "shell_thickness description"
msgid ""
"The thickness of the outside shell in the horizontal and vertical direction. "
"This is used in combination with the nozzle size to define the number of "
"perimeter lines and the thickness of those perimeter lines. This is also "
"used to define the number of solid top and bottom layers."
msgstr ""
"The thickness of the outside shell in the horizontal and vertical direction. "
"This is used in combination with the nozzle size to define the number of "
"perimeter lines and the thickness of those perimeter lines. This is also "
"used to define the number of solid top and bottom layers."

#: fdmprinter.json
msgctxt "wall_thickness label"
msgid "Wall Thickness"
msgstr "Wall Thickness"

#: fdmprinter.json
msgctxt "wall_thickness description"
msgid ""
"The thickness of the outside walls in the horizontal direction. This is used "
"in combination with the nozzle size to define the number of perimeter lines "
"and the thickness of those perimeter lines."
msgstr ""
"The thickness of the outside walls in the horizontal direction. This is used "
"in combination with the nozzle size to define the number of perimeter lines "
"and the thickness of those perimeter lines."

#: fdmprinter.json
msgctxt "wall_line_count label"
msgid "Wall Line Count"
msgstr "Wall Line Count"

#: fdmprinter.json
msgctxt "wall_line_count description"
msgid ""
"Number of shell lines. These lines are called perimeter lines in other tools "
"and impact the strength and structural integrity of your print."
msgstr ""
"Number of shell lines. These lines are called perimeter lines in other tools "
"and impact the strength and structural integrity of your print."

#: fdmprinter.json
msgctxt "alternate_extra_perimeter label"
msgid "Alternate Extra Wall"
msgstr "Alternate Extra Wall"

#: fdmprinter.json
msgctxt "alternate_extra_perimeter description"
msgid ""
"Make an extra wall at every second layer, so that infill will be caught "
"between an extra wall above and one below. This results in a better cohesion "
"between infill and walls, but might have an impact on the surface quality."
msgstr ""
"Make an extra wall at every second layer, so that infill will be caught "
"between an extra wall above and one below. This results in a better cohesion "
"between infill and walls, but might have an impact on the surface quality."

#: fdmprinter.json
msgctxt "top_bottom_thickness label"
msgid "Bottom/Top Thickness"
msgstr "Bottom/Top Thickness"

#: fdmprinter.json
msgctxt "top_bottom_thickness description"
msgid ""
"This controls the thickness of the bottom and top layers. The number of "
"solid layers put down is calculated from the layer thickness and this value. "
"Having this value a multiple of the layer thickness makes sense. Keep it "
"near your wall thickness to make an evenly strong part."
msgstr ""
"This controls the thickness of the bottom and top layers. The number of "
"solid layers put down is calculated from the layer thickness and this value. "
"Having this value a multiple of the layer thickness makes sense. Keep it "
"near your wall thickness to make an evenly strong part."

#: fdmprinter.json
msgctxt "top_thickness label"
msgid "Top Thickness"
msgstr "Top Thickness"

#: fdmprinter.json
msgctxt "top_thickness description"
msgid ""
"This controls the thickness of the top layers. The number of solid layers "
"printed is calculated from the layer thickness and this value. Having this "
"value be a multiple of the layer thickness makes sense. Keep it near your "
"wall thickness to make an evenly strong part."
msgstr ""
"This controls the thickness of the top layers. The number of solid layers "
"printed is calculated from the layer thickness and this value. Having this "
"value be a multiple of the layer thickness makes sense. Keep it near your "
"wall thickness to make an evenly strong part."

#: fdmprinter.json
msgctxt "top_layers label"
msgid "Top Layers"
msgstr "Top Layers"

#: fdmprinter.json
msgctxt "top_layers description"
msgid "This controls the number of top layers."
msgstr "This controls the number of top layers."

#: fdmprinter.json
msgctxt "bottom_thickness label"
msgid "Bottom Thickness"
msgstr "Bottom Thickness"

#: fdmprinter.json
msgctxt "bottom_thickness description"
msgid ""
"This controls the thickness of the bottom layers. The number of solid layers "
"printed is calculated from the layer thickness and this value. Having this "
"value be a multiple of the layer thickness makes sense. And keep it near to "
"your wall thickness to make an evenly strong part."
msgstr ""
"This controls the thickness of the bottom layers. The number of solid layers "
"printed is calculated from the layer thickness and this value. Having this "
"value be a multiple of the layer thickness makes sense. And keep it near to "
"your wall thickness to make an evenly strong part."

#: fdmprinter.json
msgctxt "bottom_layers label"
msgid "Bottom Layers"
msgstr "Bottom Layers"

#: fdmprinter.json
msgctxt "bottom_layers description"
msgid "This controls the amount of bottom layers."
msgstr "This controls the amount of bottom layers."

#: fdmprinter.json
msgctxt "remove_overlapping_walls_enabled label"
msgid "Remove Overlapping Wall Parts"
msgstr "Remove Overlapping Wall Parts"

#: fdmprinter.json
msgctxt "remove_overlapping_walls_enabled description"
msgid ""
"Remove parts of a wall which share an overlap which would result in "
"overextrusion in some places. These overlaps occur in thin pieces in a model "
"and sharp corners."
msgstr ""
"Remove parts of a wall which share an overlap which would result in "
"overextrusion in some places. These overlaps occur in thin pieces in a model "
"and sharp corners."

#: fdmprinter.json
msgctxt "remove_overlapping_walls_0_enabled label"
msgid "Remove Overlapping Outer Wall Parts"
msgstr "Remove Overlapping Outer Wall Parts"

#: fdmprinter.json
msgctxt "remove_overlapping_walls_0_enabled description"
msgid ""
"Remove parts of an outer wall which share an overlap which would result in "
"overextrusion in some places. These overlaps occur in thin pieces in a model "
"and sharp corners."
msgstr ""
"Remove parts of an outer wall which share an overlap which would result in "
"overextrusion in some places. These overlaps occur in thin pieces in a model "
"and sharp corners."

#: fdmprinter.json
msgctxt "remove_overlapping_walls_x_enabled label"
msgid "Remove Overlapping Other Wall Parts"
msgstr "Remove Overlapping Other Wall Parts"

#: fdmprinter.json
msgctxt "remove_overlapping_walls_x_enabled description"
msgid ""
"Remove parts of an inner wall which share an overlap which would result in "
"overextrusion in some places. These overlaps occur in thin pieces in a model "
"and sharp corners."
msgstr ""
"Remove parts of an inner wall which share an overlap which would result in "
"overextrusion in some places. These overlaps occur in thin pieces in a model "
"and sharp corners."

#: fdmprinter.json
msgctxt "travel_compensate_overlapping_walls_enabled label"
msgid "Compensate Wall Overlaps"
msgstr "Compensate Wall Overlaps"

#: fdmprinter.json
msgctxt "travel_compensate_overlapping_walls_enabled description"
msgid ""
"Compensate the flow for parts of a wall being laid down where there already "
"is a piece of a wall. These overlaps occur in thin pieces in a model. Gcode "
"generation might be slowed down considerably."
msgstr ""
"Compensate the flow for parts of a wall being laid down where there already "
"is a piece of a wall. These overlaps occur in thin pieces in a model. Gcode "
"generation might be slowed down considerably."

#: fdmprinter.json
msgctxt "fill_perimeter_gaps label"
msgid "Fill Gaps Between Walls"
msgstr "Fill Gaps Between Walls"

#: fdmprinter.json
msgctxt "fill_perimeter_gaps description"
msgid ""
"Fill the gaps created by walls where they would otherwise be overlapping. "
"This will also fill thin walls. Optionally only the gaps occurring within "
"the top and bottom skin can be filled."
msgstr ""
"Fill the gaps created by walls where they would otherwise be overlapping. "
"This will also fill thin walls. Optionally only the gaps occurring within "
"the top and bottom skin can be filled."

#: fdmprinter.json
msgctxt "fill_perimeter_gaps option nowhere"
msgid "Nowhere"
msgstr "Nowhere"

#: fdmprinter.json
msgctxt "fill_perimeter_gaps option everywhere"
msgid "Everywhere"
msgstr "Everywhere"

#: fdmprinter.json
msgctxt "fill_perimeter_gaps option skin"
msgid "Skin"
msgstr "Skin"

#: fdmprinter.json
msgctxt "top_bottom_pattern label"
msgid "Bottom/Top Pattern"
msgstr "Bottom/Top Pattern"

#: fdmprinter.json
msgctxt "top_bottom_pattern description"
msgid ""
"Pattern of the top/bottom solid fill. This is normally done with lines to "
"get the best possible finish, but in some cases a concentric fill gives a "
"nicer end result."
msgstr ""
"Pattern of the top/bottom solid fill. This is normally done with lines to "
"get the best possible finish, but in some cases a concentric fill gives a "
"nicer end result."

#: fdmprinter.json
msgctxt "top_bottom_pattern option lines"
msgid "Lines"
msgstr "Lines"

#: fdmprinter.json
msgctxt "top_bottom_pattern option concentric"
msgid "Concentric"
msgstr "Concentric"

#: fdmprinter.json
msgctxt "top_bottom_pattern option zigzag"
msgid "Zig Zag"
msgstr "Zig Zag"

#: fdmprinter.json
msgctxt "skin_no_small_gaps_heuristic label"
msgid "Ignore small Z gaps"
msgstr "Ignore small Z gaps"

#: fdmprinter.json
msgctxt "skin_no_small_gaps_heuristic description"
msgid ""
"When the model has small vertical gaps, about 5% extra computation time can "
"be spent on generating top and bottom skin in these narrow spaces. In such a "
"case set this setting to false."
msgstr ""
"When the model has small vertical gaps, about 5% extra computation time can "
"be spent on generating top and bottom skin in these narrow spaces. In such a "
"case set this setting to false."

#: fdmprinter.json
msgctxt "skin_alternate_rotation label"
msgid "Alternate Skin Rotation"
msgstr "Alternate Skin Rotation"

#: fdmprinter.json
msgctxt "skin_alternate_rotation description"
msgid ""
"Alternate between diagonal skin fill and horizontal + vertical skin fill. "
"Although the diagonal directions can print quicker, this option can improve "
"the printing quality by reducing the pillowing effect."
msgstr ""
"Alternate between diagonal skin fill and horizontal + vertical skin fill. "
"Although the diagonal directions can print quicker, this option can improve "
"the printing quality by reducing the pillowing effect."

#: fdmprinter.json
msgctxt "skin_outline_count label"
msgid "Extra Skin Wall Count"
msgstr "Extra Skin Wall Count"

#: fdmprinter.json
msgctxt "skin_outline_count description"
msgid ""
"Number of lines around skin regions. Using one or two skin perimeter lines "
"can greatly improve roofs which would start in the middle of infill cells."
msgstr ""
"Number of lines around skin regions. Using one or two skin perimeter lines "
"can greatly improve roofs which would start in the middle of infill cells."

#: fdmprinter.json
msgctxt "xy_offset label"
msgid "Horizontal expansion"
msgstr "Horizontal expansion"

#: fdmprinter.json
msgctxt "xy_offset description"
msgid ""
"Amount of offset applied to all polygons in each layer. Positive values can "
"compensate for too big holes; negative values can compensate for too small "
"holes."
msgstr ""
"Amount of offset applied to all polygons in each layer. Positive values can "
"compensate for too big holes; negative values can compensate for too small "
"holes."

#: fdmprinter.json
msgctxt "z_seam_type label"
msgid "Z Seam Alignment"
msgstr "Z Seam Alignment"

#: fdmprinter.json
msgctxt "z_seam_type description"
msgid ""
"Starting point of each path in a layer. When paths in consecutive layers "
"start at the same point a vertical seam may show on the print. When aligning "
"these at the back, the seam is easiest to remove. When placed randomly the "
"inaccuracies at the paths' start will be less noticeable. When taking the "
"shortest path the print will be quicker."
msgstr ""
"Starting point of each path in a layer. When paths in consecutive layers "
"start at the same point a vertical seam may show on the print. When aligning "
"these at the back, the seam is easiest to remove. When placed randomly the "
"inaccuracies at the paths' start will be less noticeable. When taking the "
"shortest path the print will be quicker."

#: fdmprinter.json
msgctxt "z_seam_type option back"
msgid "Back"
msgstr "Back"

#: fdmprinter.json
msgctxt "z_seam_type option shortest"
msgid "Shortest"
msgstr "Shortest"

#: fdmprinter.json
msgctxt "z_seam_type option random"
msgid "Random"
msgstr "Random"

#: fdmprinter.json
msgctxt "infill label"
msgid "Infill"
msgstr "Infill"

#: fdmprinter.json
msgctxt "infill_sparse_density label"
msgid "Infill Density"
msgstr "Infill Density"

#: fdmprinter.json
msgctxt "infill_sparse_density description"
msgid ""
"This controls how densely filled the insides of your print will be. For a "
"solid part use 100%, for a hollow part use 0%. A value around 20% is usually "
"enough. This setting won't affect the outside of the print and only adjusts "
"how strong the part becomes."
msgstr ""
"This controls how densely filled the insides of your print will be. For a "
"solid part use 100%, for a hollow part use 0%. A value around 20% is usually "
"enough. This setting won't affect the outside of the print and only adjusts "
"how strong the part becomes."

#: fdmprinter.json
msgctxt "infill_line_distance label"
msgid "Line distance"
msgstr "Line distance"

#: fdmprinter.json
msgctxt "infill_line_distance description"
msgid "Distance between the printed infill lines."
msgstr "Distance between the printed infill lines."

#: fdmprinter.json
msgctxt "infill_pattern label"
msgid "Infill Pattern"
msgstr "Infill Pattern"

#: fdmprinter.json
msgctxt "infill_pattern description"
msgid ""
"Cura defaults to switching between grid and line infill, but with this "
"setting visible you can control this yourself. The line infill swaps "
"direction on alternate layers of infill, while the grid prints the full "
"cross-hatching on each layer of infill."
msgstr ""
"Cura defaults to switching between grid and line infill, but with this "
"setting visible you can control this yourself. The line infill swaps "
"direction on alternate layers of infill, while the grid prints the full "
"cross-hatching on each layer of infill."

#: fdmprinter.json
msgctxt "infill_pattern option grid"
msgid "Grid"
msgstr "Grid"

#: fdmprinter.json
msgctxt "infill_pattern option lines"
msgid "Lines"
msgstr "Lines"

#: fdmprinter.json
msgctxt "infill_pattern option triangles"
msgid "Triangles"
msgstr "Triangles"

#: fdmprinter.json
msgctxt "infill_pattern option concentric"
msgid "Concentric"
msgstr "Concentric"

#: fdmprinter.json
msgctxt "infill_pattern option zigzag"
msgid "Zig Zag"
msgstr "Zig Zag"

#: fdmprinter.json
msgctxt "infill_overlap label"
msgid "Infill Overlap"
msgstr "Infill Overlap"

#: fdmprinter.json
msgctxt "infill_overlap description"
msgid ""
"The amount of overlap between the infill and the walls. A slight overlap "
"allows the walls to connect firmly to the infill."
msgstr ""
"The amount of overlap between the infill and the walls. A slight overlap "
"allows the walls to connect firmly to the infill."

#: fdmprinter.json
msgctxt "infill_wipe_dist label"
msgid "Infill Wipe Distance"
msgstr "Infill Wipe Distance"

#: fdmprinter.json
msgctxt "infill_wipe_dist description"
msgid ""
"Distance of a travel move inserted after every infill line, to make the "
"infill stick to the walls better. This option is similar to infill overlap, "
"but without extrusion and only on one end of the infill line."
msgstr ""
"Distance of a travel move inserted after every infill line, to make the "
"infill stick to the walls better. This option is similar to infill overlap, "
"but without extrusion and only on one end of the infill line."

#: fdmprinter.json
msgctxt "infill_sparse_thickness label"
msgid "Infill Thickness"
msgstr "Infill Thickness"

#: fdmprinter.json
msgctxt "infill_sparse_thickness description"
msgid ""
"The thickness of the sparse infill. This is rounded to a multiple of the "
"layerheight and used to print the sparse-infill in fewer, thicker layers to "
"save printing time."
msgstr ""
"The thickness of the sparse infill. This is rounded to a multiple of the "
"layerheight and used to print the sparse-infill in fewer, thicker layers to "
"save printing time."

#: fdmprinter.json
msgctxt "infill_before_walls label"
msgid "Infill Before Walls"
msgstr "Infill Before Walls"

#: fdmprinter.json
msgctxt "infill_before_walls description"
msgid ""
"Print the infill before printing the walls. Printing the walls first may "
"lead to more accurate walls, but overhangs print worse. Printing the infill "
"first leads to sturdier walls, but the infill pattern might sometimes show "
"through the surface."
msgstr ""
"Print the infill before printing the walls. Printing the walls first may "
"lead to more accurate walls, but overhangs print worse. Printing the infill "
"first leads to sturdier walls, but the infill pattern might sometimes show "
"through the surface."

#: fdmprinter.json
msgctxt "material label"
msgid "Material"
msgstr "Material"

#: fdmprinter.json
msgctxt "material_flow_dependent_temperature label"
msgid "Auto Temperature"
msgstr "Auto Temperature"

#: fdmprinter.json
msgctxt "material_flow_dependent_temperature description"
msgid ""
"Change the temperature for each layer automatically with the average flow "
"speed of that layer."
msgstr ""
"Change the temperature for each layer automatically with the average flow "
"speed of that layer."

#: fdmprinter.json
msgctxt "material_print_temperature label"
msgid "Printing Temperature"
msgstr "Printing Temperature"

#: fdmprinter.json
msgctxt "material_print_temperature description"
msgid ""
"The temperature used for printing. Set at 0 to pre-heat yourself. For PLA a "
"value of 210C is usually used.\n"
"For ABS a value of 230C or higher is required."
msgstr ""
"The temperature used for printing. Set at 0 to pre-heat yourself. For PLA a "
"value of 210C is usually used.\n"
"For ABS a value of 230C or higher is required."

#: fdmprinter.json
msgctxt "material_flow_temp_graph label"
msgid "Flow Temperature Graph"
msgstr "Flow Temperature Graph"

#: fdmprinter.json
msgctxt "material_flow_temp_graph description"
msgid "Data linking material flow (in mm/s) to temperature (degrees Celsius)."
msgstr "Data linking material flow (in mm/s) to temperature (degrees Celsius)."

#: fdmprinter.json
msgctxt "material_standby_temperature label"
msgid "Standby Temperature"
msgstr "Standby Temperature"

#: fdmprinter.json
msgctxt "material_standby_temperature description"
msgid ""
"The temperature of the nozzle when another nozzle is currently used for "
"printing."
msgstr ""
"The temperature of the nozzle when another nozzle is currently used for "
"printing."

#: fdmprinter.json
msgctxt "material_extrusion_cool_down_speed label"
msgid "Extrusion Cool Down Speed Modifier"
msgstr "Extrusion Cool Down Speed Modifier"

#: fdmprinter.json
msgctxt "material_extrusion_cool_down_speed description"
msgid ""
"The extra speed by which the nozzle cools while extruding. The same value is "
"used to signify the heat up speed lost when heating up while extruding."
msgstr ""
"The extra speed by which the nozzle cools while extruding. The same value is "
"used to signify the heat up speed lost when heating up while extruding."

#: fdmprinter.json
msgctxt "material_bed_temperature label"
msgid "Bed Temperature"
msgstr "Bed Temperature"

#: fdmprinter.json
msgctxt "material_bed_temperature description"
msgid ""
"The temperature used for the heated printer bed. Set at 0 to pre-heat it "
"yourself."
msgstr ""
"The temperature used for the heated printer bed. Set at 0 to pre-heat it "
"yourself."

#: fdmprinter.json
msgctxt "material_diameter label"
msgid "Diameter"
msgstr "Diameter"

#: fdmprinter.json
msgctxt "material_diameter description"
msgid ""
"The diameter of your filament needs to be measured as accurately as "
"possible.\n"
"If you cannot measure this value you will have to calibrate it; a higher "
"number means less extrusion, a smaller number generates more extrusion."
msgstr ""
"The diameter of your filament needs to be measured as accurately as "
"possible.\n"
"If you cannot measure this value you will have to calibrate it; a higher "
"number means less extrusion, a smaller number generates more extrusion."

#: fdmprinter.json
msgctxt "material_flow label"
msgid "Flow"
msgstr "Flow"

#: fdmprinter.json
msgctxt "material_flow description"
msgid ""
"Flow compensation: the amount of material extruded is multiplied by this "
"value."
msgstr ""
"Flow compensation: the amount of material extruded is multiplied by this "
"value."

#: fdmprinter.json
msgctxt "retraction_enable label"
msgid "Enable Retraction"
msgstr "Enable Retraction"

#: fdmprinter.json
msgctxt "retraction_enable description"
msgid ""
"Retract the filament when the nozzle is moving over a non-printed area. "
"Details about the retraction can be configured in the advanced tab."
msgstr ""
"Retract the filament when the nozzle is moving over a non-printed area. "
"Details about the retraction can be configured in the advanced tab."

#: fdmprinter.json
msgctxt "retraction_amount label"
msgid "Retraction Distance"
msgstr "Retraction Distance"

#: fdmprinter.json
msgctxt "retraction_amount description"
msgid ""
"The amount of retraction: Set at 0 for no retraction at all. A value of "
"4.5mm seems to generate good results for 3mm filament in bowden tube fed "
"printers."
msgstr ""
"The amount of retraction: Set at 0 for no retraction at all. A value of "
"4.5mm seems to generate good results for 3mm filament in bowden tube fed "
"printers."

#: fdmprinter.json
msgctxt "retraction_speed label"
msgid "Retraction Speed"
msgstr "Retraction Speed"

#: fdmprinter.json
msgctxt "retraction_speed description"
msgid ""
"The speed at which the filament is retracted. A higher retraction speed "
"works better, but a very high retraction speed can lead to filament grinding."
msgstr ""
"The speed at which the filament is retracted. A higher retraction speed "
"works better, but a very high retraction speed can lead to filament grinding."

#: fdmprinter.json
msgctxt "retraction_retract_speed label"
msgid "Retraction Retract Speed"
msgstr "Retraction Retract Speed"

#: fdmprinter.json
msgctxt "retraction_retract_speed description"
msgid ""
"The speed at which the filament is retracted. A higher retraction speed "
"works better, but a very high retraction speed can lead to filament grinding."
msgstr ""
"The speed at which the filament is retracted. A higher retraction speed "
"works better, but a very high retraction speed can lead to filament grinding."

#: fdmprinter.json
msgctxt "retraction_prime_speed label"
msgid "Retraction Prime Speed"
msgstr "Retraction Prime Speed"

#: fdmprinter.json
msgctxt "retraction_prime_speed description"
msgid "The speed at which the filament is pushed back after retraction."
msgstr "The speed at which the filament is pushed back after retraction."

#: fdmprinter.json
msgctxt "retraction_extra_prime_amount label"
msgid "Retraction Extra Prime Amount"
msgstr "Retraction Extra Prime Amount"

#: fdmprinter.json
msgctxt "retraction_extra_prime_amount description"
msgid ""
"The amount of material extruded after a retraction. During a travel move, "
"some material might get lost and so we need to compensate for this."
msgstr ""
"The amount of material extruded after a retraction. During a travel move, "
"some material might get lost and so we need to compensate for this."

#: fdmprinter.json
msgctxt "retraction_min_travel label"
msgid "Retraction Minimum Travel"
msgstr "Retraction Minimum Travel"

#: fdmprinter.json
msgctxt "retraction_min_travel description"
msgid ""
"The minimum distance of travel needed for a retraction to happen at all. "
"This helps to get fewer retractions in a small area."
msgstr ""
"The minimum distance of travel needed for a retraction to happen at all. "
"This helps to get fewer retractions in a small area."

#: fdmprinter.json
msgctxt "retraction_count_max label"
msgid "Maximum Retraction Count"
msgstr "Maximum Retraction Count"

#: fdmprinter.json
msgctxt "retraction_count_max description"
msgid ""
"This setting limits the number of retractions occurring within the Minimum "
"Extrusion Distance Window. Further retractions within this window will be "
"ignored. This avoids retracting repeatedly on the same piece of filament, as "
"that can flatten the filament and cause grinding issues."
msgstr ""
"This setting limits the number of retractions occurring within the Minimum "
"Extrusion Distance Window. Further retractions within this window will be "
"ignored. This avoids retracting repeatedly on the same piece of filament, as "
"that can flatten the filament and cause grinding issues."

#: fdmprinter.json
msgctxt "retraction_extrusion_window label"
msgid "Minimum Extrusion Distance Window"
msgstr "Minimum Extrusion Distance Window"

#: fdmprinter.json
msgctxt "retraction_extrusion_window description"
msgid ""
"The window in which the Maximum Retraction Count is enforced. This value "
"should be approximately the same as the Retraction distance, so that "
"effectively the number of times a retraction passes the same patch of "
"material is limited."
msgstr ""
"The window in which the Maximum Retraction Count is enforced. This value "
"should be approximately the same as the Retraction distance, so that "
"effectively the number of times a retraction passes the same patch of "
"material is limited."

#: fdmprinter.json
msgctxt "retraction_hop label"
msgid "Z Hop when Retracting"
msgstr "Z Hop when Retracting"

#: fdmprinter.json
msgctxt "retraction_hop description"
msgid ""
"Whenever a retraction is done, the head is lifted by this amount to travel "
"over the print. A value of 0.075 works well. This feature has a large "
"positive effect on delta towers."
msgstr ""
"Whenever a retraction is done, the head is lifted by this amount to travel "
"over the print. A value of 0.075 works well. This feature has a large "
"positive effect on delta towers."

#: fdmprinter.json
msgctxt "speed label"
msgid "Speed"
msgstr "Speed"

#: fdmprinter.json
msgctxt "speed_print label"
msgid "Print Speed"
msgstr "Print Speed"

#: fdmprinter.json
msgctxt "speed_print description"
msgid ""
"The speed at which printing happens. A well-adjusted Ultimaker can reach "
"150mm/s, but for good quality prints you will want to print slower. Printing "
"speed depends on a lot of factors, so you will need to experiment with "
"optimal settings for this."
msgstr ""
"The speed at which printing happens. A well-adjusted Ultimaker can reach "
"150mm/s, but for good quality prints you will want to print slower. Printing "
"speed depends on a lot of factors, so you will need to experiment with "
"optimal settings for this."

#: fdmprinter.json
msgctxt "speed_infill label"
msgid "Infill Speed"
msgstr "Infill Speed"

#: fdmprinter.json
msgctxt "speed_infill description"
msgid ""
"The speed at which infill parts are printed. Printing the infill faster can "
"greatly reduce printing time, but this can negatively affect print quality."
msgstr ""
"The speed at which infill parts are printed. Printing the infill faster can "
"greatly reduce printing time, but this can negatively affect print quality."

#: fdmprinter.json
msgctxt "speed_wall label"
msgid "Shell Speed"
msgstr "Shell Speed"

#: fdmprinter.json
msgctxt "speed_wall description"
msgid ""
"The speed at which the shell is printed. Printing the outer shell at a lower "
"speed improves the final skin quality."
msgstr ""
"The speed at which the shell is printed. Printing the outer shell at a lower "
"speed improves the final skin quality."

#: fdmprinter.json
msgctxt "speed_wall_0 label"
msgid "Outer Shell Speed"
msgstr "Outer Shell Speed"

#: fdmprinter.json
msgctxt "speed_wall_0 description"
msgid ""
"The speed at which the outer shell is printed. Printing the outer shell at a "
"lower speed improves the final skin quality. However, having a large "
"difference between the inner shell speed and the outer shell speed will "
"effect quality in a negative way."
msgstr ""
"The speed at which the outer shell is printed. Printing the outer shell at a "
"lower speed improves the final skin quality. However, having a large "
"difference between the inner shell speed and the outer shell speed will "
"effect quality in a negative way."

#: fdmprinter.json
msgctxt "speed_wall_x label"
msgid "Inner Shell Speed"
msgstr "Inner Shell Speed"

#: fdmprinter.json
msgctxt "speed_wall_x description"
msgid ""
"The speed at which all inner shells are printed. Printing the inner shell "
"faster than the outer shell will reduce printing time. It works well to set "
"this in between the outer shell speed and the infill speed."
msgstr ""
"The speed at which all inner shells are printed. Printing the inner shell "
"faster than the outer shell will reduce printing time. It works well to set "
"this in between the outer shell speed and the infill speed."

#: fdmprinter.json
msgctxt "speed_topbottom label"
msgid "Top/Bottom Speed"
msgstr "Top/Bottom Speed"

#: fdmprinter.json
msgctxt "speed_topbottom description"
msgid ""
"Speed at which top/bottom parts are printed. Printing the top/bottom faster "
"can greatly reduce printing time, but this can negatively affect print "
"quality."
msgstr ""
"Speed at which top/bottom parts are printed. Printing the top/bottom faster "
"can greatly reduce printing time, but this can negatively affect print "
"quality."

#: fdmprinter.json
msgctxt "speed_support label"
msgid "Support Speed"
msgstr "Support Speed"

#: fdmprinter.json
msgctxt "speed_support description"
msgid ""
"The speed at which exterior support is printed. Printing exterior supports "
"at higher speeds can greatly improve printing time. The surface quality of "
"exterior support is usually not important anyway, so higher speeds can be "
"used."
msgstr ""
"The speed at which exterior support is printed. Printing exterior supports "
"at higher speeds can greatly improve printing time. The surface quality of "
"exterior support is usually not important anyway, so higher speeds can be "
"used."

#: fdmprinter.json
msgctxt "speed_support_lines label"
msgid "Support Wall Speed"
msgstr "Support Wall Speed"

#: fdmprinter.json
msgctxt "speed_support_lines description"
msgid ""
"The speed at which the walls of exterior support are printed. Printing the "
"walls at higher speeds can improve the overall duration."
msgstr ""
"The speed at which the walls of exterior support are printed. Printing the "
"walls at higher speeds can improve the overall duration."

#: fdmprinter.json
msgctxt "speed_support_roof label"
msgid "Support Roof Speed"
msgstr "Support Roof Speed"

#: fdmprinter.json
msgctxt "speed_support_roof description"
msgid ""
"The speed at which the roofs of exterior support are printed. Printing the "
"support roof at lower speeds can improve overhang quality."
msgstr ""
"The speed at which the roofs of exterior support are printed. Printing the "
"support roof at lower speeds can improve overhang quality."

#: fdmprinter.json
msgctxt "speed_travel label"
msgid "Travel Speed"
msgstr "Travel Speed"

#: fdmprinter.json
msgctxt "speed_travel description"
msgid ""
"The speed at which travel moves are done. A well-built Ultimaker can reach "
"speeds of 250mm/s, but some machines might have misaligned layers then."
msgstr ""
"The speed at which travel moves are done. A well-built Ultimaker can reach "
"speeds of 250mm/s, but some machines might have misaligned layers then."

#: fdmprinter.json
msgctxt "speed_layer_0 label"
msgid "Bottom Layer Speed"
msgstr "Bottom Layer Speed"

#: fdmprinter.json
msgctxt "speed_layer_0 description"
msgid ""
"The print speed for the bottom layer: You want to print the first layer "
"slower so it sticks better to the printer bed."
msgstr ""
"The print speed for the bottom layer: You want to print the first layer "
"slower so it sticks better to the printer bed."

#: fdmprinter.json
msgctxt "skirt_speed label"
msgid "Skirt Speed"
msgstr "Skirt Speed"

#: fdmprinter.json
msgctxt "skirt_speed description"
msgid ""
"The speed at which the skirt and brim are printed. Normally this is done at "
"the initial layer speed, but sometimes you might want to print the skirt at "
"a different speed."
msgstr ""
"The speed at which the skirt and brim are printed. Normally this is done at "
"the initial layer speed, but sometimes you might want to print the skirt at "
"a different speed."

#: fdmprinter.json
msgctxt "speed_slowdown_layers label"
msgid "Number of Slower Layers"
msgstr "Number of Slower Layers"

#: fdmprinter.json
msgctxt "speed_slowdown_layers description"
msgid ""
"The first few layers are printed slower than the rest of the object, this to "
"get better adhesion to the printer bed and improve the overall success rate "
"of prints. The speed is gradually increased over these layers. 4 layers of "
"speed-up is generally right for most materials and printers."
msgstr ""
"The first few layers are printed slower than the rest of the object, this to "
"get better adhesion to the printer bed and improve the overall success rate "
"of prints. The speed is gradually increased over these layers. 4 layers of "
"speed-up is generally right for most materials and printers."

#: fdmprinter.json
msgctxt "travel label"
msgid "Travel"
msgstr "Travel"

#: fdmprinter.json
msgctxt "retraction_combing label"
msgid "Enable Combing"
msgstr "Enable Combing"

#: fdmprinter.json
msgctxt "retraction_combing description"
msgid ""
"Combing keeps the head within the interior of the print whenever possible "
"when traveling from one part of the print to another and does not use "
"retraction. If combing is disabled, the print head moves straight from the "
"start point to the end point and it will always retract."
msgstr ""
"Combing keeps the head within the interior of the print whenever possible "
"when traveling from one part of the print to another and does not use "
"retraction. If combing is disabled, the print head moves straight from the "
"start point to the end point and it will always retract."

#: fdmprinter.json
msgctxt "travel_avoid_other_parts label"
msgid "Avoid Printed Parts"
msgstr "Avoid Printed Parts"

#: fdmprinter.json
msgctxt "travel_avoid_other_parts description"
msgid "Avoid other parts when traveling between parts."
msgstr "Avoid other parts when traveling between parts."

#: fdmprinter.json
msgctxt "travel_avoid_distance label"
msgid "Avoid Distance"
msgstr "Avoid Distance"

#: fdmprinter.json
msgctxt "travel_avoid_distance description"
msgid "The distance to stay clear of parts which are avoided during travel."
msgstr "The distance to stay clear of parts which are avoided during travel."

#: fdmprinter.json
msgctxt "coasting_enable label"
msgid "Enable Coasting"
msgstr "Enable Coasting"

#: fdmprinter.json
msgctxt "coasting_enable description"
msgid ""
"Coasting replaces the last part of an extrusion path with a travel path. The "
"oozed material is used to lay down the last piece of the extrusion path in "
"order to reduce stringing."
msgstr ""
"Coasting replaces the last part of an extrusion path with a travel path. The "
"oozed material is used to lay down the last piece of the extrusion path in "
"order to reduce stringing."

#: fdmprinter.json
msgctxt "coasting_volume label"
msgid "Coasting Volume"
msgstr "Coasting Volume"

#: fdmprinter.json
msgctxt "coasting_volume description"
msgid ""
"The volume otherwise oozed. This value should generally be close to the "
"nozzle diameter cubed."
msgstr ""
"The volume otherwise oozed. This value should generally be close to the "
"nozzle diameter cubed."

#: fdmprinter.json
msgctxt "coasting_min_volume label"
msgid "Minimal Volume Before Coasting"
msgstr "Minimal Volume Before Coasting"

#: fdmprinter.json
msgctxt "coasting_min_volume description"
msgid ""
"The least volume an extrusion path should have to coast the full amount. For "
"smaller extrusion paths, less pressure has been built up in the bowden tube "
"and so the coasted volume is scaled linearly. This value should always be "
"larger than the Coasting Volume."
msgstr ""
"The least volume an extrusion path should have to coast the full amount. For "
"smaller extrusion paths, less pressure has been built up in the bowden tube "
"and so the coasted volume is scaled linearly. This value should always be "
"larger than the Coasting Volume."

#: fdmprinter.json
msgctxt "coasting_speed label"
msgid "Coasting Speed"
msgstr "Coasting Speed"

#: fdmprinter.json
msgctxt "coasting_speed description"
msgid ""
"The speed by which to move during coasting, relative to the speed of the "
"extrusion path. A value slightly under 100% is advised, since during the "
"coasting move the pressure in the bowden tube drops."
msgstr ""
"The speed by which to move during coasting, relative to the speed of the "
"extrusion path. A value slightly under 100% is advised, since during the "
"coasting move the pressure in the bowden tube drops."

#: fdmprinter.json
msgctxt "cooling label"
msgid "Cooling"
msgstr "Cooling"

#: fdmprinter.json
msgctxt "cool_fan_enabled label"
msgid "Enable Cooling Fan"
msgstr "Enable Cooling Fan"

#: fdmprinter.json
msgctxt "cool_fan_enabled description"
msgid ""
"Enable the cooling fan during the print. The extra cooling from the cooling "
"fan helps parts with small cross sections that print each layer quickly."
msgstr ""
"Enable the cooling fan during the print. The extra cooling from the cooling "
"fan helps parts with small cross sections that print each layer quickly."

#: fdmprinter.json
msgctxt "cool_fan_speed label"
msgid "Fan Speed"
msgstr "Fan Speed"

#: fdmprinter.json
msgctxt "cool_fan_speed description"
msgid "Fan speed used for the print cooling fan on the printer head."
msgstr "Fan speed used for the print cooling fan on the printer head."

#: fdmprinter.json
msgctxt "cool_fan_speed_min label"
msgid "Minimum Fan Speed"
msgstr "Minimum Fan Speed"

#: fdmprinter.json
msgctxt "cool_fan_speed_min description"
msgid ""
"Normally the fan runs at the minimum fan speed. If the layer is slowed down "
"due to minimum layer time, the fan speed adjusts between minimum and maximum "
"fan speed."
msgstr ""
"Normally the fan runs at the minimum fan speed. If the layer is slowed down "
"due to minimum layer time, the fan speed adjusts between minimum and maximum "
"fan speed."

#: fdmprinter.json
msgctxt "cool_fan_speed_max label"
msgid "Maximum Fan Speed"
msgstr "Maximum Fan Speed"

#: fdmprinter.json
msgctxt "cool_fan_speed_max description"
msgid ""
"Normally the fan runs at the minimum fan speed. If the layer is slowed down "
"due to minimum layer time, the fan speed adjusts between minimum and maximum "
"fan speed."
msgstr ""
"Normally the fan runs at the minimum fan speed. If the layer is slowed down "
"due to minimum layer time, the fan speed adjusts between minimum and maximum "
"fan speed."

#: fdmprinter.json
msgctxt "cool_fan_full_at_height label"
msgid "Fan Full on at Height"
msgstr "Fan Full on at Height"

#: fdmprinter.json
msgctxt "cool_fan_full_at_height description"
msgid ""
"The height at which the fan is turned on completely. For the layers below "
"this the fan speed is scaled linearly with the fan off for the first layer."
msgstr ""
"The height at which the fan is turned on completely. For the layers below "
"this the fan speed is scaled linearly with the fan off for the first layer."

#: fdmprinter.json
msgctxt "cool_fan_full_layer label"
msgid "Fan Full on at Layer"
msgstr "Fan Full on at Layer"

#: fdmprinter.json
msgctxt "cool_fan_full_layer description"
msgid ""
"The layer number at which the fan is turned on completely. For the layers "
"below this the fan speed is scaled linearly with the fan off for the first "
"layer."
msgstr ""
"The layer number at which the fan is turned on completely. For the layers "
"below this the fan speed is scaled linearly with the fan off for the first "
"layer."

#: fdmprinter.json
msgctxt "cool_min_layer_time label"
msgid "Minimum Layer Time"
msgstr "Minimum Layer Time"

#: fdmprinter.json
msgctxt "cool_min_layer_time description"
msgid ""
"The minimum time spent in a layer: Gives the layer time to cool down before "
"the next one is put on top. If a layer would print in less time, then the "
"printer will slow down to make sure it has spent at least this many seconds "
"printing the layer."
msgstr ""
"The minimum time spent in a layer: Gives the layer time to cool down before "
"the next one is put on top. If a layer would print in less time, then the "
"printer will slow down to make sure it has spent at least this many seconds "
"printing the layer."

#: fdmprinter.json
msgctxt "cool_min_layer_time_fan_speed_max label"
msgid "Minimum Layer Time Full Fan Speed"
msgstr "Minimum Layer Time Full Fan Speed"

#: fdmprinter.json
msgctxt "cool_min_layer_time_fan_speed_max description"
msgid ""
"The minimum time spent in a layer which will cause the fan to be at maximum "
"speed. The fan speed increases linearly from minimum fan speed for layers "
"taking the minimum layer time to maximum fan speed for layers taking the "
"time specified here."
msgstr ""
"The minimum time spent in a layer which will cause the fan to be at maximum "
"speed. The fan speed increases linearly from minimum fan speed for layers "
"taking the minimum layer time to maximum fan speed for layers taking the "
"time specified here."

#: fdmprinter.json
msgctxt "cool_min_speed label"
msgid "Minimum Speed"
msgstr "Minimum Speed"

#: fdmprinter.json
msgctxt "cool_min_speed description"
msgid ""
"The minimum layer time can cause the print to slow down so much it starts to "
"droop. The minimum feedrate protects against this. Even if a print gets "
"slowed down it will never be slower than this minimum speed."
msgstr ""
"The minimum layer time can cause the print to slow down so much it starts to "
"droop. The minimum feedrate protects against this. Even if a print gets "
"slowed down it will never be slower than this minimum speed."

#: fdmprinter.json
msgctxt "cool_lift_head label"
msgid "Lift Head"
msgstr "Lift Head"

#: fdmprinter.json
msgctxt "cool_lift_head description"
msgid ""
"Lift the head away from the print if the minimum speed is hit because of "
"cool slowdown, and wait the extra time away from the print surface until the "
"minimum layer time is used up."
msgstr ""
"Lift the head away from the print if the minimum speed is hit because of "
"cool slowdown, and wait the extra time away from the print surface until the "
"minimum layer time is used up."

#: fdmprinter.json
msgctxt "support label"
msgid "Support"
msgstr "Support"

#: fdmprinter.json
msgctxt "support_enable label"
msgid "Enable Support"
msgstr "Enable Support"

#: fdmprinter.json
msgctxt "support_enable description"
msgid ""
"Enable exterior support structures. This will build up supporting structures "
"below the model to prevent the model from sagging or printing in mid air."
msgstr ""
"Enable exterior support structures. This will build up supporting structures "
"below the model to prevent the model from sagging or printing in mid air."

#: fdmprinter.json
msgctxt "support_type label"
msgid "Placement"
msgstr "Placement"

#: fdmprinter.json
msgctxt "support_type description"
msgid ""
"Where to place support structures. The placement can be restricted so that "
"the support structures won't rest on the model, which could otherwise cause "
"scarring."
msgstr ""
"Where to place support structures. The placement can be restricted so that "
"the support structures won't rest on the model, which could otherwise cause "
"scarring."

#: fdmprinter.json
msgctxt "support_type option buildplate"
msgid "Touching Buildplate"
msgstr "Touching Buildplate"

#: fdmprinter.json
msgctxt "support_type option everywhere"
msgid "Everywhere"
msgstr "Everywhere"

#: fdmprinter.json
msgctxt "support_angle label"
msgid "Overhang Angle"
msgstr "Overhang Angle"

#: fdmprinter.json
msgctxt "support_angle description"
msgid ""
"The maximum angle of overhangs for which support will be added. With 0 "
"degrees being vertical, and 90 degrees being horizontal. A smaller overhang "
"angle leads to more support."
msgstr ""
"The maximum angle of overhangs for which support will be added. With 0 "
"degrees being vertical, and 90 degrees being horizontal. A smaller overhang "
"angle leads to more support."

#: fdmprinter.json
msgctxt "support_xy_distance label"
msgid "X/Y Distance"
msgstr "X/Y Distance"

#: fdmprinter.json
msgctxt "support_xy_distance description"
msgid ""
"Distance of the support structure from the print in the X/Y directions. "
"0.7mm typically gives a nice distance from the print so the support does not "
"stick to the surface."
msgstr ""
"Distance of the support structure from the print in the X/Y directions. "
"0.7mm typically gives a nice distance from the print so the support does not "
"stick to the surface."

#: fdmprinter.json
msgctxt "support_z_distance label"
msgid "Z Distance"
msgstr "Z Distance"

#: fdmprinter.json
msgctxt "support_z_distance description"
msgid ""
"Distance from the top/bottom of the support to the print. A small gap here "
"makes it easier to remove the support but makes the print a bit uglier. "
"0.15mm allows for easier separation of the support structure."
msgstr ""
"Distance from the top/bottom of the support to the print. A small gap here "
"makes it easier to remove the support but makes the print a bit uglier. "
"0.15mm allows for easier separation of the support structure."

#: fdmprinter.json
msgctxt "support_top_distance label"
msgid "Top Distance"
msgstr "Top Distance"

#: fdmprinter.json
msgctxt "support_top_distance description"
msgid "Distance from the top of the support to the print."
msgstr "Distance from the top of the support to the print."

#: fdmprinter.json
msgctxt "support_bottom_distance label"
msgid "Bottom Distance"
msgstr "Bottom Distance"

#: fdmprinter.json
msgctxt "support_bottom_distance description"
msgid "Distance from the print to the bottom of the support."
msgstr "Distance from the print to the bottom of the support."

#: fdmprinter.json
msgctxt "support_conical_enabled label"
msgid "Conical Support"
msgstr "Conical Support"

#: fdmprinter.json
msgctxt "support_conical_enabled description"
msgid ""
"Experimental feature: Make support areas smaller at the bottom than at the "
"overhang."
msgstr ""
"Experimental feature: Make support areas smaller at the bottom than at the "
"overhang."

#: fdmprinter.json
msgctxt "support_conical_angle label"
msgid "Cone Angle"
msgstr "Cone Angle"

#: fdmprinter.json
msgctxt "support_conical_angle description"
msgid ""
"The angle of the tilt of conical support. With 0 degrees being vertical, and "
"90 degrees being horizontal. Smaller angles cause the support to be more "
"sturdy, but consist of more material. Negative angles cause the base of the "
"support to be wider than the top."
msgstr ""
"The angle of the tilt of conical support. With 0 degrees being vertical, and "
"90 degrees being horizontal. Smaller angles cause the support to be more "
"sturdy, but consist of more material. Negative angles cause the base of the "
"support to be wider than the top."

#: fdmprinter.json
msgctxt "support_conical_min_width label"
msgid "Minimal Width"
msgstr "Minimal Width"

#: fdmprinter.json
msgctxt "support_conical_min_width description"
msgid ""
"Minimal width to which conical support reduces the support areas. Small "
"widths can cause the base of the support to not act well as foundation for "
"support above."
msgstr ""
"Minimal width to which conical support reduces the support areas. Small "
"widths can cause the base of the support to not act well as foundation for "
"support above."

#: fdmprinter.json
msgctxt "support_bottom_stair_step_height label"
msgid "Stair Step Height"
msgstr "Stair Step Height"

#: fdmprinter.json
msgctxt "support_bottom_stair_step_height description"
msgid ""
"The height of the steps of the stair-like bottom of support resting on the "
"model. Small steps can cause the support to be hard to remove from the top "
"of the model."
msgstr ""
"The height of the steps of the stair-like bottom of support resting on the "
"model. Small steps can cause the support to be hard to remove from the top "
"of the model."

#: fdmprinter.json
msgctxt "support_join_distance label"
msgid "Join Distance"
msgstr "Join Distance"

#: fdmprinter.json
msgctxt "support_join_distance description"
msgid ""
"The maximum distance between support blocks in the X/Y directions, so that "
"the blocks will merge into a single block."
msgstr ""
"The maximum distance between support blocks in the X/Y directions, so that "
"the blocks will merge into a single block."

#: fdmprinter.json
msgctxt "support_offset label"
msgid "Horizontal Expansion"
msgstr "Horizontal Expansion"

#: fdmprinter.json
msgctxt "support_offset description"
msgid ""
"Amount of offset applied to all support polygons in each layer. Positive "
"values can smooth out the support areas and result in more sturdy support."
msgstr ""
"Amount of offset applied to all support polygons in each layer. Positive "
"values can smooth out the support areas and result in more sturdy support."

#: fdmprinter.json
msgctxt "support_area_smoothing label"
msgid "Area Smoothing"
msgstr "Area Smoothing"

#: fdmprinter.json
msgctxt "support_area_smoothing description"
msgid ""
"Maximum distance in the X/Y directions of a line segment which is to be "
"smoothed out. Ragged lines are introduced by the join distance and support "
"bridge, which cause the machine to resonate. Smoothing the support areas "
"won't cause them to break with the constraints, except it might change the "
"overhang."
msgstr ""
"Maximum distance in the X/Y directions of a line segment which is to be "
"smoothed out. Ragged lines are introduced by the join distance and support "
"bridge, which cause the machine to resonate. Smoothing the support areas "
"won't cause them to break with the constraints, except it might change the "
"overhang."

#: fdmprinter.json
msgctxt "support_roof_enable label"
msgid "Enable Support Roof"
msgstr "Enable Support Roof"

#: fdmprinter.json
msgctxt "support_roof_enable description"
msgid ""
"Generate a dense top skin at the top of the support on which the model sits."
msgstr ""
"Generate a dense top skin at the top of the support on which the model sits."

#: fdmprinter.json
msgctxt "support_roof_height label"
msgid "Support Roof Thickness"
msgstr "Support Roof Thickness"

#: fdmprinter.json
msgctxt "support_roof_height description"
msgid "The height of the support roofs."
msgstr "The height of the support roofs."

#: fdmprinter.json
msgctxt "support_roof_density label"
msgid "Support Roof Density"
msgstr "Support Roof Density"

#: fdmprinter.json
msgctxt "support_roof_density description"
msgid ""
"This controls how densely filled the roofs of the support will be. A higher "
"percentage results in better overhangs, but makes the support more difficult "
"to remove."
msgstr ""
"This controls how densely filled the roofs of the support will be. A higher "
"percentage results in better overhangs, but makes the support more difficult "
"to remove."

#: fdmprinter.json
msgctxt "support_roof_line_distance label"
msgid "Support Roof Line Distance"
msgstr "Support Roof Line Distance"

#: fdmprinter.json
msgctxt "support_roof_line_distance description"
msgid "Distance between the printed support roof lines."
msgstr "Distance between the printed support roof lines."

#: fdmprinter.json
msgctxt "support_roof_pattern label"
msgid "Support Roof Pattern"
msgstr "Support Roof Pattern"

#: fdmprinter.json
msgctxt "support_roof_pattern description"
msgid "The pattern with which the top of the support is printed."
msgstr "The pattern with which the top of the support is printed."

#: fdmprinter.json
msgctxt "support_roof_pattern option lines"
msgid "Lines"
msgstr "Lines"

#: fdmprinter.json
msgctxt "support_roof_pattern option grid"
msgid "Grid"
msgstr "Grid"

#: fdmprinter.json
msgctxt "support_roof_pattern option triangles"
msgid "Triangles"
msgstr "Triangles"

#: fdmprinter.json
msgctxt "support_roof_pattern option concentric"
msgid "Concentric"
msgstr "Concentric"

#: fdmprinter.json
msgctxt "support_roof_pattern option zigzag"
msgid "Zig Zag"
msgstr "Zig Zag"

#: fdmprinter.json
msgctxt "support_use_towers label"
msgid "Use towers"
msgstr "Use towers"

#: fdmprinter.json
msgctxt "support_use_towers description"
msgid ""
"Use specialized towers to support tiny overhang areas. These towers have a "
"larger diameter than the region they support. Near the overhang the towers' "
"diameter decreases, forming a roof."
msgstr ""
"Use specialized towers to support tiny overhang areas. These towers have a "
"larger diameter than the region they support. Near the overhang the towers' "
"diameter decreases, forming a roof."

#: fdmprinter.json
msgctxt "support_minimal_diameter label"
msgid "Minimum Diameter"
msgstr "Minimum Diameter"

#: fdmprinter.json
msgctxt "support_minimal_diameter description"
msgid ""
"Minimum diameter in the X/Y directions of a small area which is to be "
"supported by a specialized support tower."
msgstr ""
"Minimum diameter in the X/Y directions of a small area which is to be "
"supported by a specialized support tower."

#: fdmprinter.json
msgctxt "support_tower_diameter label"
msgid "Tower Diameter"
msgstr "Tower Diameter"

#: fdmprinter.json
msgctxt "support_tower_diameter description"
msgid "The diameter of a special tower."
msgstr "The diameter of a special tower."

#: fdmprinter.json
msgctxt "support_tower_roof_angle label"
msgid "Tower Roof Angle"
msgstr "Tower Roof Angle"

#: fdmprinter.json
msgctxt "support_tower_roof_angle description"
msgid ""
"The angle of the rooftop of a tower. Larger angles mean more pointy towers."
msgstr ""
"The angle of the rooftop of a tower. Larger angles mean more pointy towers."

#: fdmprinter.json
msgctxt "support_pattern label"
msgid "Pattern"
msgstr "Pattern"

#: fdmprinter.json
msgctxt "support_pattern description"
msgid ""
"Cura can generate 3 distinct types of support structure. First is a grid "
"based support structure which is quite solid and can be removed in one "
"piece. The second is a line based support structure which has to be peeled "
"off line by line. The third is a structure in between the other two; it "
"consists of lines which are connected in an accordion fashion."
msgstr ""
"Cura can generate 3 distinct types of support structure. First is a grid "
"based support structure which is quite solid and can be removed in one "
"piece. The second is a line based support structure which has to be peeled "
"off line by line. The third is a structure in between the other two; it "
"consists of lines which are connected in an accordion fashion."

#: fdmprinter.json
msgctxt "support_pattern option lines"
msgid "Lines"
msgstr "Lines"

#: fdmprinter.json
msgctxt "support_pattern option grid"
msgid "Grid"
msgstr "Grid"

#: fdmprinter.json
msgctxt "support_pattern option triangles"
msgid "Triangles"
msgstr "Triangles"

#: fdmprinter.json
msgctxt "support_pattern option concentric"
msgid "Concentric"
msgstr "Concentric"

#: fdmprinter.json
msgctxt "support_pattern option zigzag"
msgid "Zig Zag"
msgstr "Zig Zag"

#: fdmprinter.json
msgctxt "support_connect_zigzags label"
msgid "Connect ZigZags"
msgstr "Connect ZigZags"

#: fdmprinter.json
msgctxt "support_connect_zigzags description"
msgid ""
"Connect the ZigZags. Makes them harder to remove, but prevents stringing of "
"disconnected zigzags."
msgstr ""
"Connect the ZigZags. Makes them harder to remove, but prevents stringing of "
"disconnected zigzags."

#: fdmprinter.json
msgctxt "support_infill_rate label"
msgid "Fill Amount"
msgstr "Fill Amount"

#: fdmprinter.json
msgctxt "support_infill_rate description"
msgid ""
"The amount of infill structure in the support; less infill gives weaker "
"support which is easier to remove."
msgstr ""
"The amount of infill structure in the support; less infill gives weaker "
"support which is easier to remove."

#: fdmprinter.json
msgctxt "support_line_distance label"
msgid "Line distance"
msgstr "Line distance"

#: fdmprinter.json
msgctxt "support_line_distance description"
msgid "Distance between the printed support lines."
msgstr "Distance between the printed support lines."

#: fdmprinter.json
msgctxt "platform_adhesion label"
msgid "Platform Adhesion"
msgstr "Platform Adhesion"

#: fdmprinter.json
msgctxt "adhesion_type label"
msgid "Type"
msgstr "Type"

#: fdmprinter.json
msgctxt "adhesion_type description"
msgid ""
"Different options that help to improve priming your extrusion.\n"
"Brim and Raft help in preventing corners from lifting due to warping. Brim "
"adds a single-layer-thick flat area around your object which is easy to cut "
"off afterwards, and it is the recommended option.\n"
"Raft adds a thick grid below the object and a thin interface between this "
"and your object.\n"
"The skirt is a line drawn around the first layer of the print, this helps to "
"prime your extrusion and to see if the object fits on your platform."
msgstr ""
"Different options that help to improve priming your extrusion.\n"
"Brim and Raft help in preventing corners from lifting due to warping. Brim "
"adds a single-layer-thick flat area around your object which is easy to cut "
"off afterwards, and it is the recommended option.\n"
"Raft adds a thick grid below the object and a thin interface between this "
"and your object.\n"
"The skirt is a line drawn around the first layer of the print, this helps to "
"prime your extrusion and to see if the object fits on your platform."

#: fdmprinter.json
msgctxt "adhesion_type option skirt"
msgid "Skirt"
msgstr "Skirt"

#: fdmprinter.json
msgctxt "adhesion_type option brim"
msgid "Brim"
msgstr "Brim"

#: fdmprinter.json
msgctxt "adhesion_type option raft"
msgid "Raft"
msgstr "Raft"

#: fdmprinter.json
msgctxt "skirt_line_count label"
msgid "Skirt Line Count"
msgstr "Skirt Line Count"

#: fdmprinter.json
msgctxt "skirt_line_count description"
msgid ""
"Multiple skirt lines help to prime your extrusion better for small objects. "
"Setting this to 0 will disable the skirt."
msgstr ""
"Multiple skirt lines help to prime your extrusion better for small objects. "
"Setting this to 0 will disable the skirt."

#: fdmprinter.json
msgctxt "skirt_gap label"
msgid "Skirt Distance"
msgstr "Skirt Distance"

#: fdmprinter.json
msgctxt "skirt_gap description"
msgid ""
"The horizontal distance between the skirt and the first layer of the print.\n"
"This is the minimum distance, multiple skirt lines will extend outwards from "
"this distance."
msgstr ""
"The horizontal distance between the skirt and the first layer of the print.\n"
"This is the minimum distance, multiple skirt lines will extend outwards from "
"this distance."

#: fdmprinter.json
msgctxt "skirt_minimal_length label"
msgid "Skirt Minimum Length"
msgstr "Skirt Minimum Length"

#: fdmprinter.json
msgctxt "skirt_minimal_length description"
msgid ""
"The minimum length of the skirt. If this minimum length is not reached, more "
"skirt lines will be added to reach this minimum length. Note: If the line "
"count is set to 0 this is ignored."
msgstr ""
"The minimum length of the skirt. If this minimum length is not reached, more "
"skirt lines will be added to reach this minimum length. Note: If the line "
"count is set to 0 this is ignored."

#: fdmprinter.json
msgctxt "brim_width label"
msgid "Brim Width"
msgstr "Brim Width"

#: fdmprinter.json
msgctxt "brim_width description"
msgid ""
"The distance from the model to the end of the brim. A larger brim sticks "
"better to the build platform, but also makes your effective print area "
"smaller."
msgstr ""
"The distance from the model to the end of the brim. A larger brim sticks "
"better to the build platform, but also makes your effective print area "
"smaller."

#: fdmprinter.json
msgctxt "brim_line_count label"
msgid "Brim Line Count"
msgstr "Brim Line Count"

#: fdmprinter.json
msgctxt "brim_line_count description"
msgid ""
"The number of lines used for a brim. More lines means a larger brim which "
"sticks better to the build plate, but this also makes your effective print "
"area smaller."
msgstr ""
"The number of lines used for a brim. More lines means a larger brim which "
"sticks better to the build plate, but this also makes your effective print "
"area smaller."

#: fdmprinter.json
msgctxt "raft_margin label"
msgid "Raft Extra Margin"
msgstr "Raft Extra Margin"

#: fdmprinter.json
msgctxt "raft_margin description"
msgid ""
"If the raft is enabled, this is the extra raft area around the object which "
"is also given a raft. Increasing this margin will create a stronger raft "
"while using more material and leaving less area for your print."
msgstr ""
"If the raft is enabled, this is the extra raft area around the object which "
"is also given a raft. Increasing this margin will create a stronger raft "
"while using more material and leaving less area for your print."

#: fdmprinter.json
msgctxt "raft_airgap label"
msgid "Raft Air-gap"
msgstr "Raft Air-gap"

#: fdmprinter.json
msgctxt "raft_airgap description"
msgid ""
"The gap between the final raft layer and the first layer of the object. Only "
"the first layer is raised by this amount to lower the bonding between the "
"raft layer and the object. Makes it easier to peel off the raft."
msgstr ""
"The gap between the final raft layer and the first layer of the object. Only "
"the first layer is raised by this amount to lower the bonding between the "
"raft layer and the object. Makes it easier to peel off the raft."

#: fdmprinter.json
msgctxt "raft_surface_layers label"
msgid "Raft Top Layers"
msgstr "Raft Top Layers"

#: fdmprinter.json
msgctxt "raft_surface_layers description"
msgid ""
"The number of top layers on top of the 2nd raft layer. These are fully "
"filled layers that the object sits on. 2 layers result in a smoother top "
"surface than 1."
msgstr ""
"The number of top layers on top of the 2nd raft layer. These are fully "
"filled layers that the object sits on. 2 layers result in a smoother top "
"surface than 1."

#: fdmprinter.json
msgctxt "raft_surface_thickness label"
msgid "Raft Top Layer Thickness"
msgstr "Raft Top Layer Thickness"

#: fdmprinter.json
msgctxt "raft_surface_thickness description"
msgid "Layer thickness of the top raft layers."
msgstr "Layer thickness of the top raft layers."

#: fdmprinter.json
msgctxt "raft_surface_line_width label"
msgid "Raft Top Line Width"
msgstr "Raft Top Line Width"

#: fdmprinter.json
msgctxt "raft_surface_line_width description"
msgid ""
"Width of the lines in the top surface of the raft. These can be thin lines "
"so that the top of the raft becomes smooth."
msgstr ""
"Width of the lines in the top surface of the raft. These can be thin lines "
"so that the top of the raft becomes smooth."

#: fdmprinter.json
msgctxt "raft_surface_line_spacing label"
msgid "Raft Top Spacing"
msgstr "Raft Top Spacing"

#: fdmprinter.json
msgctxt "raft_surface_line_spacing description"
msgid ""
"The distance between the raft lines for the top raft layers. The spacing "
"should be equal to the line width, so that the surface is solid."
msgstr ""
"The distance between the raft lines for the top raft layers. The spacing "
"should be equal to the line width, so that the surface is solid."

#: fdmprinter.json
msgctxt "raft_interface_thickness label"
msgid "Raft Middle Thickness"
msgstr "Raft Middle Thickness"

#: fdmprinter.json
msgctxt "raft_interface_thickness description"
msgid "Layer thickness of the middle raft layer."
msgstr "Layer thickness of the middle raft layer."

#: fdmprinter.json
msgctxt "raft_interface_line_width label"
msgid "Raft Middle Line Width"
msgstr "Raft Middle Line Width"

#: fdmprinter.json
msgctxt "raft_interface_line_width description"
msgid ""
"Width of the lines in the middle raft layer. Making the second layer extrude "
"more causes the lines to stick to the bed."
msgstr ""
"Width of the lines in the middle raft layer. Making the second layer extrude "
"more causes the lines to stick to the bed."

#: fdmprinter.json
msgctxt "raft_interface_line_spacing label"
msgid "Raft Middle Spacing"
msgstr "Raft Middle Spacing"

#: fdmprinter.json
msgctxt "raft_interface_line_spacing description"
msgid ""
"The distance between the raft lines for the middle raft layer. The spacing "
"of the middle should be quite wide, while being dense enough to support the "
"top raft layers."
msgstr ""
"The distance between the raft lines for the middle raft layer. The spacing "
"of the middle should be quite wide, while being dense enough to support the "
"top raft layers."

#: fdmprinter.json
msgctxt "raft_base_thickness label"
msgid "Raft Base Thickness"
msgstr "Raft Base Thickness"

#: fdmprinter.json
msgctxt "raft_base_thickness description"
msgid ""
"Layer thickness of the base raft layer. This should be a thick layer which "
"sticks firmly to the printer bed."
msgstr ""
"Layer thickness of the base raft layer. This should be a thick layer which "
"sticks firmly to the printer bed."

#: fdmprinter.json
msgctxt "raft_base_line_width label"
msgid "Raft Base Line Width"
msgstr "Raft Base Line Width"

#: fdmprinter.json
msgctxt "raft_base_line_width description"
msgid ""
"Width of the lines in the base raft layer. These should be thick lines to "
"assist in bed adhesion."
msgstr ""
"Width of the lines in the base raft layer. These should be thick lines to "
"assist in bed adhesion."

#: fdmprinter.json
msgctxt "raft_base_line_spacing label"
msgid "Raft Line Spacing"
msgstr "Raft Line Spacing"

#: fdmprinter.json
msgctxt "raft_base_line_spacing description"
msgid ""
"The distance between the raft lines for the base raft layer. Wide spacing "
"makes for easy removal of the raft from the build plate."
msgstr ""
"The distance between the raft lines for the base raft layer. Wide spacing "
"makes for easy removal of the raft from the build plate."

#: fdmprinter.json
msgctxt "raft_speed label"
msgid "Raft Print Speed"
msgstr "Raft Print Speed"

#: fdmprinter.json
msgctxt "raft_speed description"
msgid "The speed at which the raft is printed."
msgstr "The speed at which the raft is printed."

#: fdmprinter.json
msgctxt "raft_surface_speed label"
msgid "Raft Surface Print Speed"
msgstr "Raft Surface Print Speed"

#: fdmprinter.json
msgctxt "raft_surface_speed description"
msgid ""
"The speed at which the surface raft layers are printed. These should be "
"printed a bit slower, so that the nozzle can slowly smooth out adjacent "
"surface lines."
msgstr ""
"The speed at which the surface raft layers are printed. These should be "
"printed a bit slower, so that the nozzle can slowly smooth out adjacent "
"surface lines."

#: fdmprinter.json
msgctxt "raft_interface_speed label"
msgid "Raft Interface Print Speed"
msgstr "Raft Interface Print Speed"

#: fdmprinter.json
msgctxt "raft_interface_speed description"
msgid ""
"The speed at which the interface raft layer is printed. This should be "
"printed quite slowly, as the volume of material coming out of the nozzle is "
"quite high."
msgstr ""
"The speed at which the interface raft layer is printed. This should be "
"printed quite slowly, as the volume of material coming out of the nozzle is "
"quite high."

#: fdmprinter.json
msgctxt "raft_base_speed label"
msgid "Raft Base Print Speed"
msgstr "Raft Base Print Speed"

#: fdmprinter.json
msgctxt "raft_base_speed description"
msgid ""
"The speed at which the base raft layer is printed. This should be printed "
"quite slowly, as the volume of material coming out of the nozzle is quite "
"high."
msgstr ""
"The speed at which the base raft layer is printed. This should be printed "
"quite slowly, as the volume of material coming out of the nozzle is quite "
"high."

#: fdmprinter.json
msgctxt "raft_fan_speed label"
msgid "Raft Fan Speed"
msgstr "Raft Fan Speed"

#: fdmprinter.json
msgctxt "raft_fan_speed description"
msgid "The fan speed for the raft."
msgstr "The fan speed for the raft."

#: fdmprinter.json
msgctxt "raft_surface_fan_speed label"
msgid "Raft Surface Fan Speed"
msgstr "Raft Surface Fan Speed"

#: fdmprinter.json
msgctxt "raft_surface_fan_speed description"
msgid "The fan speed for the surface raft layers."
msgstr "The fan speed for the surface raft layers."

#: fdmprinter.json
msgctxt "raft_interface_fan_speed label"
msgid "Raft Interface Fan Speed"
msgstr "Raft Interface Fan Speed"

#: fdmprinter.json
msgctxt "raft_interface_fan_speed description"
msgid "The fan speed for the interface raft layer."
msgstr "The fan speed for the interface raft layer."

#: fdmprinter.json
msgctxt "raft_base_fan_speed label"
msgid "Raft Base Fan Speed"
msgstr "Raft Base Fan Speed"

#: fdmprinter.json
msgctxt "raft_base_fan_speed description"
msgid "The fan speed for the base raft layer."
msgstr "The fan speed for the base raft layer."

#: fdmprinter.json
msgctxt "draft_shield_enabled label"
msgid "Enable Draft Shield"
msgstr "Enable Draft Shield"

#: fdmprinter.json
msgctxt "draft_shield_enabled description"
msgid ""
"Enable exterior draft shield. This will create a wall around the object "
"which traps (hot) air and shields against gusts of wind. Especially useful "
"for materials which warp easily."
msgstr ""
"Enable exterior draft shield. This will create a wall around the object "
"which traps (hot) air and shields against gusts of wind. Especially useful "
"for materials which warp easily."

#: fdmprinter.json
msgctxt "draft_shield_dist label"
msgid "Draft Shield X/Y Distance"
msgstr "Draft Shield X/Y Distance"

#: fdmprinter.json
msgctxt "draft_shield_dist description"
msgid "Distance of the draft shield from the print, in the X/Y directions."
msgstr "Distance of the draft shield from the print, in the X/Y directions."

#: fdmprinter.json
msgctxt "draft_shield_height_limitation label"
msgid "Draft Shield Limitation"
msgstr "Draft Shield Limitation"

#: fdmprinter.json
msgctxt "draft_shield_height_limitation description"
msgid "Whether or not to limit the height of the draft shield."
msgstr "Whether or not to limit the height of the draft shield."

#: fdmprinter.json
msgctxt "draft_shield_height_limitation option full"
msgid "Full"
msgstr "Full"

#: fdmprinter.json
msgctxt "draft_shield_height_limitation option limited"
msgid "Limited"
msgstr "Limited"

#: fdmprinter.json
msgctxt "draft_shield_height label"
msgid "Draft Shield Height"
msgstr "Draft Shield Height"

#: fdmprinter.json
msgctxt "draft_shield_height description"
msgid ""
"Height limitation on the draft shield. Above this height no draft shield "
"will be printed."
msgstr ""
"Height limitation on the draft shield. Above this height no draft shield "
"will be printed."

#: fdmprinter.json
msgctxt "meshfix label"
msgid "Mesh Fixes"
msgstr "Mesh Fixes"

#: fdmprinter.json
msgctxt "meshfix_union_all label"
msgid "Union Overlapping Volumes"
msgstr "Union Overlapping Volumes"

#: fdmprinter.json
msgctxt "meshfix_union_all description"
msgid ""
"Ignore the internal geometry arising from overlapping volumes and print the "
"volumes as one. This may cause internal cavities to disappear."
msgstr ""
"Ignore the internal geometry arising from overlapping volumes and print the "
"volumes as one. This may cause internal cavities to disappear."

#: fdmprinter.json
msgctxt "meshfix_union_all_remove_holes label"
msgid "Remove All Holes"
msgstr "Remove All Holes"

#: fdmprinter.json
msgctxt "meshfix_union_all_remove_holes description"
msgid ""
"Remove the holes in each layer and keep only the outside shape. This will "
"ignore any invisible internal geometry. However, it also ignores layer holes "
"which can be viewed from above or below."
msgstr ""
"Remove the holes in each layer and keep only the outside shape. This will "
"ignore any invisible internal geometry. However, it also ignores layer holes "
"which can be viewed from above or below."

#: fdmprinter.json
msgctxt "meshfix_extensive_stitching label"
msgid "Extensive Stitching"
msgstr "Extensive Stitching"

#: fdmprinter.json
msgctxt "meshfix_extensive_stitching description"
msgid ""
"Extensive stitching tries to stitch up open holes in the mesh by closing the "
"hole with touching polygons. This option can introduce a lot of processing "
"time."
msgstr ""
"Extensive stitching tries to stitch up open holes in the mesh by closing the "
"hole with touching polygons. This option can introduce a lot of processing "
"time."

#: fdmprinter.json
msgctxt "meshfix_keep_open_polygons label"
msgid "Keep Disconnected Faces"
msgstr "Keep Disconnected Faces"

#: fdmprinter.json
msgctxt "meshfix_keep_open_polygons description"
msgid ""
"Normally Cura tries to stitch up small holes in the mesh and remove parts of "
"a layer with big holes. Enabling this option keeps those parts which cannot "
"be stitched. This option should be used as a last resort option when "
"everything else fails to produce proper GCode."
msgstr ""
"Normally Cura tries to stitch up small holes in the mesh and remove parts of "
"a layer with big holes. Enabling this option keeps those parts which cannot "
"be stitched. This option should be used as a last resort option when "
"everything else fails to produce proper GCode."

#: fdmprinter.json
msgctxt "blackmagic label"
msgid "Special Modes"
msgstr "Special Modes"

#: fdmprinter.json
msgctxt "print_sequence label"
msgid "Print sequence"
msgstr "Print sequence"

#: fdmprinter.json
msgctxt "print_sequence description"
msgid ""
"Whether to print all objects one layer at a time or to wait for one object "
"to finish, before moving on to the next. One at a time mode is only possible "
"if all models are separated in such a way that the whole print head can move "
"in between and all models are lower than the distance between the nozzle and "
"the X/Y axes."
msgstr ""
"Whether to print all objects one layer at a time or to wait for one object "
"to finish, before moving on to the next. One at a time mode is only possible "
"if all models are separated in such a way that the whole print head can move "
"in between and all models are lower than the distance between the nozzle and "
"the X/Y axes."

#: fdmprinter.json
msgctxt "print_sequence option all_at_once"
msgid "All at Once"
msgstr "All at Once"

#: fdmprinter.json
msgctxt "print_sequence option one_at_a_time"
msgid "One at a Time"
msgstr "One at a Time"

#: fdmprinter.json
msgctxt "magic_mesh_surface_mode label"
msgid "Surface Mode"
msgstr "Surface Mode"

#: fdmprinter.json
msgctxt "magic_mesh_surface_mode description"
msgid ""
"Print the surface instead of the volume. No infill, no top/bottom skin, just "
"a single wall of which the middle coincides with the surface of the mesh. "
"It's also possible to do both: print the insides of a closed volume as "
"normal, but print all polygons not part of a closed volume as surface."
msgstr ""
"Print the surface instead of the volume. No infill, no top/bottom skin, just "
"a single wall of which the middle coincides with the surface of the mesh. "
"It's also possible to do both: print the insides of a closed volume as "
"normal, but print all polygons not part of a closed volume as surface."

#: fdmprinter.json
msgctxt "magic_mesh_surface_mode option normal"
msgid "Normal"
msgstr "Normal"

#: fdmprinter.json
msgctxt "magic_mesh_surface_mode option surface"
msgid "Surface"
msgstr "Surface"

#: fdmprinter.json
msgctxt "magic_mesh_surface_mode option both"
msgid "Both"
msgstr "Both"

#: fdmprinter.json
msgctxt "magic_spiralize label"
msgid "Spiralize Outer Contour"
msgstr "Spiralize Outer Contour"

#: fdmprinter.json
msgctxt "magic_spiralize description"
msgid ""
"Spiralize smooths out the Z move of the outer edge. This will create a "
"steady Z increase over the whole print. This feature turns a solid object "
"into a single walled print with a solid bottom. This feature used to be "
"called Joris in older versions."
msgstr ""
"Spiralize smooths out the Z move of the outer edge. This will create a "
"steady Z increase over the whole print. This feature turns a solid object "
"into a single walled print with a solid bottom. This feature used to be "
"called Joris in older versions."

#: fdmprinter.json
msgctxt "magic_fuzzy_skin_enabled label"
msgid "Fuzzy Skin"
msgstr "Fuzzy Skin"

#: fdmprinter.json
msgctxt "magic_fuzzy_skin_enabled description"
msgid ""
"Randomly jitter while printing the outer wall, so that the surface has a "
"rough and fuzzy look."
msgstr ""
"Randomly jitter while printing the outer wall, so that the surface has a "
"rough and fuzzy look."

#: fdmprinter.json
msgctxt "magic_fuzzy_skin_thickness label"
msgid "Fuzzy Skin Thickness"
msgstr "Fuzzy Skin Thickness"

#: fdmprinter.json
msgctxt "magic_fuzzy_skin_thickness description"
msgid ""
"The width within which to jitter. It's advised to keep this below the outer "
"wall width, since the inner walls are unaltered."
msgstr ""
"The width within which to jitter. It's advised to keep this below the outer "
"wall width, since the inner walls are unaltered."

#: fdmprinter.json
msgctxt "magic_fuzzy_skin_point_density label"
msgid "Fuzzy Skin Density"
msgstr "Fuzzy Skin Density"

#: fdmprinter.json
msgctxt "magic_fuzzy_skin_point_density description"
msgid ""
"The average density of points introduced on each polygon in a layer. Note "
"that the original points of the polygon are discarded, so a low density "
"results in a reduction of the resolution."
msgstr ""
"The average density of points introduced on each polygon in a layer. Note "
"that the original points of the polygon are discarded, so a low density "
"results in a reduction of the resolution."

#: fdmprinter.json
msgctxt "magic_fuzzy_skin_point_dist label"
msgid "Fuzzy Skin Point Distance"
msgstr "Fuzzy Skin Point Distance"

#: fdmprinter.json
msgctxt "magic_fuzzy_skin_point_dist description"
msgid ""
"The average distance between the random points introduced on each line "
"segment. Note that the original points of the polygon are discarded, so a "
"high smoothness results in a reduction of the resolution. This value must be "
"higher than half the Fuzzy Skin Thickness."
msgstr ""
"The average distance between the random points introduced on each line "
"segment. Note that the original points of the polygon are discarded, so a "
"high smoothness results in a reduction of the resolution. This value must be "
"higher than half the Fuzzy Skin Thickness."

#: fdmprinter.json
msgctxt "wireframe_enabled label"
msgid "Wire Printing"
msgstr "Wire Printing"

#: fdmprinter.json
msgctxt "wireframe_enabled description"
msgid ""
"Print only the outside surface with a sparse webbed structure, printing 'in "
"thin air'. This is realized by horizontally printing the contours of the "
"model at given Z intervals which are connected via upward and diagonally "
"downward lines."
msgstr ""
"Print only the outside surface with a sparse webbed structure, printing 'in "
"thin air'. This is realized by horizontally printing the contours of the "
"model at given Z intervals which are connected via upward and diagonally "
"downward lines."

#: fdmprinter.json
msgctxt "wireframe_height label"
msgid "WP Connection Height"
msgstr "WP Connection Height"

#: fdmprinter.json
msgctxt "wireframe_height description"
msgid ""
"The height of the upward and diagonally downward lines between two "
"horizontal parts. This determines the overall density of the net structure. "
"Only applies to Wire Printing."
msgstr ""
"The height of the upward and diagonally downward lines between two "
"horizontal parts. This determines the overall density of the net structure. "
"Only applies to Wire Printing."

#: fdmprinter.json
msgctxt "wireframe_roof_inset label"
msgid "WP Roof Inset Distance"
msgstr "WP Roof Inset Distance"

#: fdmprinter.json
msgctxt "wireframe_roof_inset description"
msgid ""
"The distance covered when making a connection from a roof outline inward. "
"Only applies to Wire Printing."
msgstr ""
"The distance covered when making a connection from a roof outline inward. "
"Only applies to Wire Printing."

#: fdmprinter.json
msgctxt "wireframe_printspeed label"
msgid "WP speed"
msgstr "WP speed"

#: fdmprinter.json
msgctxt "wireframe_printspeed description"
msgid ""
"Speed at which the nozzle moves when extruding material. Only applies to "
"Wire Printing."
msgstr ""
"Speed at which the nozzle moves when extruding material. Only applies to "
"Wire Printing."

#: fdmprinter.json
msgctxt "wireframe_printspeed_bottom label"
msgid "WP Bottom Printing Speed"
msgstr "WP Bottom Printing Speed"

#: fdmprinter.json
msgctxt "wireframe_printspeed_bottom description"
msgid ""
"Speed of printing the first layer, which is the only layer touching the "
"build platform. Only applies to Wire Printing."
msgstr ""
"Speed of printing the first layer, which is the only layer touching the "
"build platform. Only applies to Wire Printing."

#: fdmprinter.json
msgctxt "wireframe_printspeed_up label"
msgid "WP Upward Printing Speed"
msgstr "WP Upward Printing Speed"

#: fdmprinter.json
msgctxt "wireframe_printspeed_up description"
msgid ""
"Speed of printing a line upward 'in thin air'. Only applies to Wire Printing."
msgstr ""
"Speed of printing a line upward 'in thin air'. Only applies to Wire Printing."

#: fdmprinter.json
msgctxt "wireframe_printspeed_down label"
msgid "WP Downward Printing Speed"
msgstr "WP Downward Printing Speed"

#: fdmprinter.json
msgctxt "wireframe_printspeed_down description"
msgid ""
"Speed of printing a line diagonally downward. Only applies to Wire Printing."
msgstr ""
"Speed of printing a line diagonally downward. Only applies to Wire Printing."

#: fdmprinter.json
msgctxt "wireframe_printspeed_flat label"
msgid "WP Horizontal Printing Speed"
msgstr "WP Horizontal Printing Speed"

#: fdmprinter.json
msgctxt "wireframe_printspeed_flat description"
msgid ""
"Speed of printing the horizontal contours of the object. Only applies to "
"Wire Printing."
msgstr ""
"Speed of printing the horizontal contours of the object. Only applies to "
"Wire Printing."

#: fdmprinter.json
msgctxt "wireframe_flow label"
msgid "WP Flow"
msgstr "WP Flow"

#: fdmprinter.json
msgctxt "wireframe_flow description"
msgid ""
"Flow compensation: the amount of material extruded is multiplied by this "
"value. Only applies to Wire Printing."
msgstr ""
"Flow compensation: the amount of material extruded is multiplied by this "
"value. Only applies to Wire Printing."

#: fdmprinter.json
msgctxt "wireframe_flow_connection label"
msgid "WP Connection Flow"
msgstr "WP Connection Flow"

#: fdmprinter.json
msgctxt "wireframe_flow_connection description"
msgid "Flow compensation when going up or down. Only applies to Wire Printing."
msgstr ""
"Flow compensation when going up or down. Only applies to Wire Printing."

#: fdmprinter.json
msgctxt "wireframe_flow_flat label"
msgid "WP Flat Flow"
msgstr "WP Flat Flow"

#: fdmprinter.json
msgctxt "wireframe_flow_flat description"
msgid ""
"Flow compensation when printing flat lines. Only applies to Wire Printing."
msgstr ""
"Flow compensation when printing flat lines. Only applies to Wire Printing."

#: fdmprinter.json
msgctxt "wireframe_top_delay label"
msgid "WP Top Delay"
msgstr "WP Top Delay"

#: fdmprinter.json
msgctxt "wireframe_top_delay description"
msgid ""
"Delay time after an upward move, so that the upward line can harden. Only "
"applies to Wire Printing."
msgstr ""
"Delay time after an upward move, so that the upward line can harden. Only "
"applies to Wire Printing."

#: fdmprinter.json
msgctxt "wireframe_bottom_delay label"
msgid "WP Bottom Delay"
msgstr "WP Bottom Delay"

#: fdmprinter.json
msgctxt "wireframe_bottom_delay description"
msgid "Delay time after a downward move. Only applies to Wire Printing."
msgstr "Delay time after a downward move. Only applies to Wire Printing."

#: fdmprinter.json
msgctxt "wireframe_flat_delay label"
msgid "WP Flat Delay"
msgstr "WP Flat Delay"

#: fdmprinter.json
msgctxt "wireframe_flat_delay description"
msgid ""
"Delay time between two horizontal segments. Introducing such a delay can "
"cause better adhesion to previous layers at the connection points, while too "
"long delays cause sagging. Only applies to Wire Printing."
msgstr ""
"Delay time between two horizontal segments. Introducing such a delay can "
"cause better adhesion to previous layers at the connection points, while too "
"long delays cause sagging. Only applies to Wire Printing."

#: fdmprinter.json
msgctxt "wireframe_up_half_speed label"
msgid "WP Ease Upward"
msgstr "WP Ease Upward"

#: fdmprinter.json
msgctxt "wireframe_up_half_speed description"
msgid ""
"Distance of an upward move which is extruded with half speed.\n"
"This can cause better adhesion to previous layers, while not heating the "
"material in those layers too much. Only applies to Wire Printing."
msgstr ""
"Distance of an upward move which is extruded with half speed.\n"
"This can cause better adhesion to previous layers, while not heating the "
"material in those layers too much. Only applies to Wire Printing."

#: fdmprinter.json
msgctxt "wireframe_top_jump label"
msgid "WP Knot Size"
msgstr "WP Knot Size"

#: fdmprinter.json
msgctxt "wireframe_top_jump description"
msgid ""
"Creates a small knot at the top of an upward line, so that the consecutive "
"horizontal layer has a better chance to connect to it. Only applies to Wire "
"Printing."
msgstr ""
"Creates a small knot at the top of an upward line, so that the consecutive "
"horizontal layer has a better chance to connect to it. Only applies to Wire "
"Printing."

#: fdmprinter.json
msgctxt "wireframe_fall_down label"
msgid "WP Fall Down"
msgstr "WP Fall Down"

#: fdmprinter.json
msgctxt "wireframe_fall_down description"
msgid ""
"Distance with which the material falls down after an upward extrusion. This "
"distance is compensated for. Only applies to Wire Printing."
msgstr ""
"Distance with which the material falls down after an upward extrusion. This "
"distance is compensated for. Only applies to Wire Printing."

#: fdmprinter.json
msgctxt "wireframe_drag_along label"
msgid "WP Drag along"
msgstr "WP Drag along"

#: fdmprinter.json
msgctxt "wireframe_drag_along description"
msgid ""
"Distance with which the material of an upward extrusion is dragged along "
"with the diagonally downward extrusion. This distance is compensated for. "
"Only applies to Wire Printing."
msgstr ""
"Distance with which the material of an upward extrusion is dragged along "
"with the diagonally downward extrusion. This distance is compensated for. "
"Only applies to Wire Printing."

#: fdmprinter.json
msgctxt "wireframe_strategy label"
msgid "WP Strategy"
msgstr "WP Strategy"

#: fdmprinter.json
msgctxt "wireframe_strategy description"
msgid ""
"Strategy for making sure two consecutive layers connect at each connection "
"point. Retraction lets the upward lines harden in the right position, but "
"may cause filament grinding. A knot can be made at the end of an upward line "
"to heighten the chance of connecting to it and to let the line cool; "
"however, it may require slow printing speeds. Another strategy is to "
"compensate for the sagging of the top of an upward line; however, the lines "
"won't always fall down as predicted."
msgstr ""
"Strategy for making sure two consecutive layers connect at each connection "
"point. Retraction lets the upward lines harden in the right position, but "
"may cause filament grinding. A knot can be made at the end of an upward line "
"to heighten the chance of connecting to it and to let the line cool; "
"however, it may require slow printing speeds. Another strategy is to "
"compensate for the sagging of the top of an upward line; however, the lines "
"won't always fall down as predicted."

#: fdmprinter.json
msgctxt "wireframe_strategy option compensate"
msgid "Compensate"
msgstr "Compensate"

#: fdmprinter.json
msgctxt "wireframe_strategy option knot"
msgid "Knot"
msgstr "Knot"

#: fdmprinter.json
msgctxt "wireframe_strategy option retract"
msgid "Retract"
msgstr "Retract"

#: fdmprinter.json
msgctxt "wireframe_straight_before_down label"
msgid "WP Straighten Downward Lines"
msgstr "WP Straighten Downward Lines"

#: fdmprinter.json
msgctxt "wireframe_straight_before_down description"
msgid ""
"Percentage of a diagonally downward line which is covered by a horizontal "
"line piece. This can prevent sagging of the top most point of upward lines. "
"Only applies to Wire Printing."
msgstr ""
"Percentage of a diagonally downward line which is covered by a horizontal "
"line piece. This can prevent sagging of the top most point of upward lines. "
"Only applies to Wire Printing."

#: fdmprinter.json
msgctxt "wireframe_roof_fall_down label"
msgid "WP Roof Fall Down"
msgstr "WP Roof Fall Down"

#: fdmprinter.json
msgctxt "wireframe_roof_fall_down description"
msgid ""
"The distance which horizontal roof lines printed 'in thin air' fall down "
"when being printed. This distance is compensated for. Only applies to Wire "
"Printing."
msgstr ""
"The distance which horizontal roof lines printed 'in thin air' fall down "
"when being printed. This distance is compensated for. Only applies to Wire "
"Printing."

#: fdmprinter.json
msgctxt "wireframe_roof_drag_along label"
msgid "WP Roof Drag Along"
msgstr "WP Roof Drag Along"

#: fdmprinter.json
msgctxt "wireframe_roof_drag_along description"
msgid ""
"The distance of the end piece of an inward line which gets dragged along "
"when going back to the outer outline of the roof. This distance is "
"compensated for. Only applies to Wire Printing."
msgstr ""
"The distance of the end piece of an inward line which gets dragged along "
"when going back to the outer outline of the roof. This distance is "
"compensated for. Only applies to Wire Printing."

#: fdmprinter.json
msgctxt "wireframe_roof_outer_delay label"
msgid "WP Roof Outer Delay"
msgstr "WP Roof Outer Delay"

#: fdmprinter.json
msgctxt "wireframe_roof_outer_delay description"
msgid ""
"Time spent at the outer perimeters of hole which is to become a roof. Longer "
"times can ensure a better connection. Only applies to Wire Printing."
msgstr ""
"Time spent at the outer perimeters of hole which is to become a roof. Longer "
"times can ensure a better connection. Only applies to Wire Printing."

#: fdmprinter.json
msgctxt "wireframe_nozzle_clearance label"
msgid "WP Nozzle Clearance"
msgstr "WP Nozzle Clearance"

#: fdmprinter.json
msgctxt "wireframe_nozzle_clearance description"
msgid ""
"Distance between the nozzle and horizontally downward lines. Larger "
"clearance results in diagonally downward lines with a less steep angle, "
"which in turn results in less upward connections with the next layer. Only "
"applies to Wire Printing."
msgstr ""
"Distance between the nozzle and horizontally downward lines. Larger "
"clearance results in diagonally downward lines with a less steep angle, "
"which in turn results in less upward connections with the next layer. Only "
"applies to Wire Printing."