Cura/resources/definitions/tronxy_x5sa_500.def.json

{
    "version": 2,
    "name": "Tronxy X5SA/X5ST/Pro/2E 500mm",
    "inherits": "tronxy_x",
    "metadata":
    {
        "visible": true,
        "platform": "tronxy.stl",
        "quality_definition": "tronxy_x"
    },
    "overrides":
    {
        "gantry_height": { "value": 40 },
        "machine_acceleration": { "value": 150 },
        "machine_depth": { "default_value": 500 },
        "machine_end_gcode": { "default_value": "G91 ; Set Positioning to Relative\nM83 ; Set Extruder to Relative\nG92 E0 ; Reset Extruder\nG1 E-4 F3000 ; Retract 4mm of filament\nG1 Z0.2 ; Raise nozzle .2mm\nG90 ; Set positioning to absolute\nG1 X{machine_width} Y{machine_depth} ; Park print head\nG91 ; Set Positioning to RelativeG1 Z10 ; Raise nozzle 10mm\nM106 S0 ; Turn off part fan\nM104 S0 ; Set nozzle temp to zero\nM140 S0 ; set bed temp to zero\nM84 X Y Z E ; Disable X Y Z and E steppers\n" },
        "machine_head_with_fans_polygon":
        {
            "default_value": [
                [-48, 45],
                [-48, -30],
                [27, -30],
                [27, 45]
            ]
        },
        "machine_height": { "default_value": 600 },
        "machine_name": { "default_value": "Tronxy X5SA 500" },
        "machine_start_gcode": { "default_value": "; X5SA Start Code\nG21 ; Set units to millimeters\nG90 ; Set all axis to Absolute\nM82 ; Set extrusion to Absolute\nM107 ; Disable all fans\nM190 S{material_bed_temperature_layer_0} ; Set bed temperature and wait\nG28 ; Home all axis\n; Uncomment the line below to enable ABL Mesh probing\n;G29 ; Probe bed mesh for ABL\n; For best results do not run nozzle heater while performing ABL\nG1 Z5.0 ; Raise nozzle to prevent scratching of heat bed\nG1 X0 Y0 ; Move nozzle to Home before heating\nM109 S{material_print_temperature_layer_0} T0 ; Set nozzle temp and wait\nG92 E0 ; Set Extruder position to zero\n; Uncomment the following lines to enable nozzle purge line along left edge of bed\n;G1 Z2.0 F3000 ; Raise Z axis\n;G1 X1.1 Y20 Z0.2 F3600.0 ; Move to purge line start position\n;G1 Y290 F1500.0 E15 ; Draw first purge line\n;G1 X1.4 F3600.0 ; Move to side\n;G1 Y20 F1500.0 E30 ; Draw second purge line\n;G92 E0 ; Reset Extruder\n;G1 Z2.0 F3000 ; Move Z Axis up little to prevent scratching of Heat Bed\n;G1 X5 Y20 Z0.2 F3600.0 ; Move over to finish nozzle wipe\n;G92 E0\n" },
        "machine_width": { "default_value": 500 },
        "retraction_amount": { "value": 6.5 }
    }
}