Cura/resources/definitions/jgaurora_a1.def.json

{
    "name": "JGAurora A1",
    "version": 2,
    "inherits": "fdmprinter",
    "metadata": {
        "visible": true,
        "author": "Samuel Pinches",
        "manufacturer": "JGAurora",
        "file_formats": "text/x-gcode",
        "preferred_quality_type": "fast",
        "machine_extruder_trains":
        {
            "0": "jgaurora_a1_extruder_0"
        }
    },
    "overrides": {
        "machine_name": {
            "default_value": "JGAurora A1"
        },
        "machine_start_gcode": {
            "default_value": "; -- START GCODE --\nG21                     ;set units to millimetres\nG90                     ;set to absolute positioning\nM106 S0                 ;set fan speed to zero (turned off)\nG28                     ;home all axis\nM420 S1                 ;turn on mesh bed levelling if enabled in firmware\nG92 E0                  ;zero the extruded length\nG1 Z1 F1000             ;move up slightly\nG1 X60.0 Z0 E9.0 F1000.0;intro line\nG1 X100.0 E21.5 F1000.0 ;continue line\nG92 E0                  ;zero the extruded length again\n; -- end of START GCODE --"
        },
        "machine_end_gcode": {
            "default_value": "; -- END GCODE --\nM104 S0                 ;turn off nozzle heater\nM140 S0                 ;turn off bed heater\nG91                     ;set to relative positioning\nG1 E-10 F300            ;retract the filament slightly\nG90                     ;set to absolute positioning\nG28 X0                  ;move to the X-axis origin (Home)\nG0 Y280 F600            ;bring the bed to the front for easy print removal\nM84                     ;turn off stepper motors\n; -- end of END GCODE --"
        },        
        "machine_width": {
            "default_value": 300
        },
        "machine_height": {
            "default_value": 300
        },
        "machine_depth": {
            "default_value": 300
        },
        "machine_heated_bed": {
            "default_value": true
        },
        "machine_center_is_zero": {
            "default_value": false
        },
        "gantry_height": {
            "default_value": 10
        },
        "machine_gcode_flavor": {
            "default_value": "RepRap (Marlin/Sprinter)"
        },
        "material_diameter": {
            "default_value": 1.75
        },
        "material_print_temperature": {
            "default_value": 215
        },
        "material_bed_temperature": {
            "default_value": 67
        },
        "layer_height_0": {
            "default_value": 0.12
        },
        "wall_thickness": {
            "default_value": 1.2
        },
        "speed_print": {
            "default_value": 40
        },
        "speed_infill": {
            "default_value": 40
        },
        "speed_wall": {
            "default_value": 35
        },
        "speed_topbottom": {
            "default_value": 35
        },
        "speed_travel": {
            "default_value": 120
        },
        "speed_layer_0": {
            "default_value": 12
        },
        "support_enable": {
            "default_value": true
        },
        "retraction_enable": {
            "default_value": true
        },
        "retraction_amount": {
            "default_value": 6
        },
        "retraction_speed": {
            "default_value": 40
        }
    }
}