Cura/resources/settings/witbox.json

{
    "id": "bq_witbox",
    "version": 1, 
    "name": "BQ Witbox",
    "manufacturer": "BQ",
    "author": "other",
    "platform": "witbox_platform.stl",
    "inherits": "fdmprinter.json",

    "machine_settings": {
        "machine_start_gcode": {
            "default": "; -- START GCODE --\n;Sliced at: {day} {date} {time}\n;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {infill_density}\n;Print time: {print_time}\n;Filament used: {filament_amount}m {filament_weight}g\n;Filament cost: {filament_cost}\nG21                     ;set units to millimetres\nG90                     ;set to absolute positioning\nM106 S0                 ;set fan speed to zero (turned off)\nG28 X0 Y0               ;move to the X/Y origin (Home)\nG28 Z0                  ;move to the Z origin (Home)\nG1 Z15.0 F1200          ;move Z to position 15.0 mm\nG92 E0                  ;zero the extruded length\nG1 E20 F200             ;extrude 20mm of feed stock\nG92 E0                  ;zero the extruded length again\nG1 F7200                ;set feedrate to 120 mm/sec\n; -- end of START GCODE --"
        },
        "machine_end_gcode": {
            "default": "; -- END GCODE --\nM104 S0                 ;set extruder temperature to zero (turned off)\nG91                     ;set to relative positioning\nG1 E-20 F300            ;retract the filament a bit to release some of the pressure\nG90                     ;set to absolute positioning\nG1 Z200                 ;move the platform to the bottom\nG28 X0 Y0               ;move to the X/Y origin (Home)\nM84                     ;turn off steppers\n; -- end of END GCODE --"
        },
        "machine_width": {
            "default": 297
        },
        "machine_depth": {
            "default": 210
        },
        "machine_height": {
            "default": 200
        },
        "machine_heated_bed": {
            "default": false
        },
        "machine_center_is_zero": {
            "default": false
        },
        "machine_gcode_flavor": {
            "default": "RepRap"
        },
        "machine_platform_offset": {
            "default": [0, -145, -38]
        }
    },
    "overrides": {
        "layer_height": { "default": 0.2 },
        "layer_height_0": { "default": 0.2, "visible": true },
        "shell_thickness": { "default": 1.2},
        "wall_thickness": { "default": 1.2, "visible": false },
        "top_bottom_thickness": { "default": 0.8, "visible": false},
        "bottom_thickness": { "default": 0.4, "visible": false },
        "material_print_temperature": { "default": 220, "visible": true },
        "material_bed_temperature": { "default": 0, "visible": false },
        "material_diameter": { "default": 1.75, "visible": true },
        "speed_print": { "default": 40.0},
        "speed_infill": { "default": 40.0, "visible": false },
        "speed_wall": { "default":35.0, "visible": false},
        "speed_wall_0": { "default": 35.0, "visible": false },
        "speed_wall_x": { "default": 35.0, "visible": false },
        "speed_topbottom": { "default": 35.0, "visible": false },
        "speed_support": { "default": 35.0, "visible": false },
        "speed_travel": { "default": 120.0 },
        "speed_layer_0": { "default": 20.0, "visible": false },
        "retraction_speed": { "default": 30.0, "visible": true},
        "retraction_retract_speed": { "default": 30.0, "visible": true },
        "retraction_prime_speed": { "default": 30.0, "visible": true },
        "retraction_amount": { "default": 2.0, "visible": true },
        "retraction_hop": { "default": 0.75, "visible": false },
        "skirt_minimal_length": { "default": 150 },
        "raft_base_line_width": { "default": 0.7 },
        "raft_interface_thickness": { "default": 0.2 },
        "support_enable": { "default": true },
        "support_z_distance": { "default": 0.2, "visible": false },
        "support_infill_rate": { "default": 10, "visible": false }
    }
}