Cura/resources/definitions/mendel90.def.json

{
    "version": 2,
    "name": "Mendel90",
    "inherits": "fdmprinter",
    "metadata":
    {
        "visible": true,
        "author": "Wilmer Gaona",
        "manufacturer": "Nophead",
        "file_formats": "text/x-gcode",
        "platform": "mendel90_platform.3mf",
        "machine_extruder_trains": { "0": "mendel90_extruder_0" },
        "platform_offset": [
            0,
            -23.6,
            0
        ]
    },
    "overrides":
    {
        "gantry_height": { "value": "55" },
        "machine_center_is_zero": { "default_value": true },
        "machine_depth": { "default_value": 200 },
        "machine_end_gcode": { "default_value": "M104 S0 ;extruder heater off\nM140 S0 ;heated bed heater off (if you have it)\nM107 ;carriage fan off\nG91 ;relative positioning\nG1 Z10 ;Move up Z 10mm\nG90 ;back to absolute mode\nG1 E-1 F1200 ;retract the filament a bit before lifting the nozzle, to release some of the pressure\nG92 E0 ;zero the extruded length\nG1 Z200 X-100 F9000 ; go to top\nG1 Y100 F5000 ;Move Y to back\nM42 P42 S255 ;Turn on Bed cooling fan on\nG4 S10 ;Wait 10 seconds\nM42 P42 S0 ;Turn off bed cooling fan\nM84 ;steppers off\n" },
        "machine_extruder_count": { "default_value": 1 },
        "machine_gcode_flavor": { "default_value": "RepRap (Marlin/Sprinter)" },
        "machine_head_with_fans_polygon":
        {
            "default_value": [
                [-12, 9],
                [-12, -9],
                [14, 9],
                [14, -9]
            ]
        },
        "machine_heat_zone_length": { "default_value": 16 },
        "machine_heated_bed": { "default_value": true },
        "machine_height": { "default_value": 200 },
        "machine_name": { "default_value": "Mendel90" },
        "machine_nozzle_head_distance": { "default_value": 5 },
        "machine_nozzle_tip_outer_diameter": { "default_value": 1 },
        "machine_start_gcode": { "default_value": "G21 ;metric values\nG90 ;absolute positioning\nM82 ;absolute extrusion\nM107 ;start with the fan off\nG28 ;home\nG92 E0 ;zero the extruded length\nM140 S{material_bed_temperature_layer_0} ; set the bed temperature and continue on\nG1 X-50 Y98 F9000 ;go to the left of the top\nG1 Z0.05 ; close to the bed\nM104 S{material_print_temperature_layer_0}; pre-heat the extruder continue on\nM190 S{material_bed_temperature_layer_0} ;set the bed temp & wait\nM109 S{material_print_temperature_layer_0};set the extruder temp for layer 0 & wait\nG92 E0 ;zero the extruded length\nG1 X50 E10 F300 ; make a thick line to prime extruder\nG92 E0 ; reset extruder\nG1 E-4 F1800\nG1 Z0.3 ;lift Z\n" },
        "machine_width": { "default_value": 200 },
        "material_bed_temp_wait": { "default_value": true },
        "material_print_temp_prepend": { "default_value": true }
    },
    "pages": [ "BedLeveling" ]
}