[general]
version = 4
name = Normal Quality
definition = nwa3d_a31

[metadata]
setting_version = 20
type = quality
quality_type = normal
weight = 0
global_quality = True

[values]
layer_height = 0.16
layer_height_0 = 0.24
line_width = 0.4
wall_line_width_0 = 0.4
initial_layer_line_width_factor = 100
wall_thickness = 0.8
wall_0_wipe_dist = 0.2
roofing_layer_count = 1
top_bottom_thickness = 0.6
top_thickness = 0.8
top_layers = 5
bottom_thickness = 0.6
bottom_layers = 3
top_bottom_pattern = lines
top_bottom_pattern_0 = lines
wall_0_inset = 0
optimize_wall_printing_order = False
inset_direction = inside_out
alternate_extra_perimeter = False
fill_outline_gaps = True
xy_offset = 0
skin_no_small_gaps_heuristic = True
skin_outline_count = 1
ironing_enabled = False
infill_sparse_density = 20
zig_zaggify_infill = False
infill_multiplier = 1
infill_wall_line_count = 0
infill_overlap = 10
skin_overlap = 5
infill_wipe_dist = 0.1
gradual_infill_steps = 0
infill_before_walls = False
infill_support_enabled = False
max_skin_angle_for_expansion = 90
material_diameter = 1.75
default_material_print_temperature = 220
material_print_temperature = 220
material_print_temperature_layer_0 = 220
material_initial_print_temperature = 220
material_final_print_temperature = 220
default_material_bed_temperature = 50
material_bed_temperature = 50
material_flow = 100
retraction_enable = True
retract_at_layer_change = False
retraction_amount = 5
retraction_speed = 45
retraction_extra_prime_amount = 0
retraction_min_travel = 0.8
retraction_count_max = 90
retraction_extrusion_window = 5
limit_support_retractions = True
switch_extruder_retraction_amount = 16
switch_extruder_retraction_speeds = 20
speed_print = 50
speed_travel = 150
speed_layer_0 = 10
speed_travel_layer_0 = 50
speed_slowdown_layers = 2
acceleration_enabled = False
acceleration_roofing = 3000
jerk_enabled = False
retraction_combing = off
travel_retract_before_outer_wall = False
retraction_hop_enabled = False
cool_fan_enabled = True
cool_fan_speed = 100
cool_fan_speed_0 = 0
cool_fan_full_at_height = 0.32
cool_lift_head = False
support_enable = True
support_type = everywhere
support_angle = 50
support_pattern = grid
support_wall_count = 0
zig_zaggify_support = False
support_infill_rate = =20 if support_enable and support_structure == 'normal' else 0 if support_enable and support_structure == 'tree' else 20
support_infill_angles = [0]
support_brim_enable = True
support_brim_line_count = 5
support_z_distance = 0.21
support_xy_distance = 0.7
support_xy_distance_overhang = 0.2
support_bottom_stair_step_height = 0.3
support_bottom_stair_step_width = 5.0
support_join_distance = 2.0
support_offset = 0.2
gradual_support_infill_steps = 0
support_roof_enable = True
support_bottom_enable = False
support_roof_height = 0.45
support_roof_density = 45
support_roof_pattern = lines
support_fan_enable = False
support_use_towers = True
support_tower_diameter = 3
support_tower_roof_angle = 65
adhesion_type = skirt
skirt_line_count = 2
skirt_gap = 3
meshfix_union_all = True
meshfix_union_all_remove_holes = False
meshfix_extensive_stitching = False
meshfix_keep_open_polygons = False
multiple_mesh_overlap = 0.16
carve_multiple_volumes = False