{
    "id": "RF100",
    "version": 2,
    "name": "Renkforce RF100",
    "inherits": "fdmprinter",
    "metadata": {
        "author": "Simon Peter (based on RF100.ini by Conrad Electronic SE)",
        "category": "Other",
        "file_formats": "text/x-gcode",
        "manufacturer": "Renkforce",
        "visible": true
    },

    "overrides": {
        "adhesion_type": {
            "default_value": "skirt"
        },
        "bottom_thickness": {
            "value": 0.5
        },
        "brim_line_count": {
            "default_value": 20.0
        },
        "cool_fan_enabled": {
            "default_value": true
        },
        "cool_fan_full_at_height": {
            "default_value": 0.5
        },
        "cool_fan_speed_max": {
            "default_value": 100.0
        },
        "cool_fan_speed_min": {
            "default_value": 100.0
        },
        "cool_lift_head": {
            "default_value": true
        },
        "cool_min_layer_time": {
            "default_value": 5.0
        },
        "cool_min_speed": {
            "default_value": 10.0
        },
        "infill_before_walls": {
            "default_value": true
        },
        "infill_overlap": {
            "default_value": 15.0
        },
        "layer_0_z_overlap": {
            "default_value": 0.22
        },
        "layer_height_0": {
            "default_value": 0.3
        },
        "machine_depth": {
            "default_value": 100
        },
        "machine_end_gcode": {
            "default_value": ";End GCode\nM104 S0 ;extruder heater off\nM140 S0 ;heated bed heater off (if you have it)\nG91 ;relative positioning\nG1 E-1 F300 ;retract the filament a bit before lifting the nozzle, to release some of the pressure\nG1 Z+0.5 E-5 X-20 Y-20 F{speed_travel} ;move Z up a bit and retract filament even more\nG28 X0 Y0 ;move X/Y to min endstops, so the head is out of the way\nM84 ;steppers off\nG90 ;absolute positioning"
        },
        "machine_gcode_flavor": {
            "default_value": "RepRap (Marlin/Sprinter)"
        },
        "machine_height": {
            "default_value": 100
        },
        "machine_name": {
            "default_value": "Renkforce RF100"
        },
        "machine_start_gcode": {
            "default_value": ";Sliced at: {day} {date} {time}\nG21 ;metric values\nG90 ;absolute positioning\nM82 ;set extruder to absolute mode\nM107 ;start with the fan off\nG28 X0 Y0 ;move X/Y to min endstops\nG28 Z0 ;move Z to min endstops\nG1 Z15.0 F{speed_travel} ;move the platform down 15mm\nG92 E0 ;zero the extruded length\nG1 F200 E3 ;extrude 3mm of feed stock\nG92 E0 ;zero the extruded length again\nG1 F{speed_travel}\nM117 Printing..."
        },
        "machine_width": {
            "default_value": 100
        },
        "material_bed_temperature": {
            "visible": false
        },
        "material_diameter": {
            "default_value": 1.75
        },
        "material_print_temperature": {
            "default_value": 210.0
        },
        "ooze_shield_enabled": {
            "default_value": true
        },
        "raft_airgap": {
            "default_value": 0.22
        },
        "raft_base_line_spacing": {
            "default_value": 3.0
        },
        "raft_base_line_width": {
            "default_value": 1.0
        },
        "raft_base_thickness": {
            "default_value": 0.3
        },
        "raft_interface_line_spacing": {
            "default_value": 3.0
        },
        "raft_interface_line_width": {
            "default_value": 0.4
        },
        "raft_interface_thickness": {
            "default_value": 0.27
        },
        "raft_margin": {
            "default_value": 5.0
        },
        "raft_surface_layers": {
            "default_value": 2.0
        },
        "raft_surface_line_spacing": {
            "default_value": 3.0
        },
        "raft_surface_line_width": {
            "default_value": 0.4
        },
        "raft_surface_thickness": {
            "default_value": 0.27
        },
        "retraction_amount": {
            "default_value": 2.0
        },
        "retraction_combing": {
            "default_value": "all"
        },
        "retraction_enable": {
            "default_value": true
        },
        "retraction_hop_enabled": {
            "default_value": 1.0
        },
        "retraction_min_travel": {
            "default_value": 1.5
        },
        "retraction_speed": {
            "default_value": 40.0
        },
        "skin_overlap": {
            "default_value": 15.0
        },
        "skirt_brim_minimal_length": {
            "default_value": 150.0
        },
        "skirt_gap": {
            "default_value": 3.0
        },
        "skirt_line_count": {
            "default_value": 1.0
        },
        "speed_infill": {
            "default_value": 50.0
        },
        "speed_layer_0": {
            "default_value": 30.0
        },
        "speed_print": {
            "default_value": 50.0
        },
        "speed_topbottom": {
            "default_value": 30.0
        },
        "speed_travel": {
            "default_value": 50.0
        },
        "speed_wall_0": {
            "default_value": 25.0
        },
        "speed_wall_x": {
            "default_value": 35.0
        },
        "support_angle": {
            "default_value": 60.0
        },
        "support_enable": {
            "default_value": 0.0
        },
        "support_infill_rate": {
            "default_value": 15.0
        },
        "support_pattern": {
            "default_value": "lines"
        },
        "support_type": {
            "default_value": "everywhere"
        },
        "support_xy_distance": {
            "default_value": 0.5
        },
        "support_z_distance": {
            "default_value": 0.1
        },
        "top_thickness": {
            "default_value": 0.5
        },
        "wall_thickness": {
            "default_value": 0.8
        }
    }
}