|
|
@@ -21,12 +21,13 @@
|
|
|
},
|
|
|
"overrides": {
|
|
|
"machine_name": { "default_value": "Diytech 220" },
|
|
|
- "machine_start_gcode" : {
|
|
|
- "value": "\"\" if machine_gcode_flavor == \"UltiGCode\" else \"G21 ;metric values\\nG90 ;absolute positioning\\nM82 ;set extruder to absolute mode\\nM107 ;start with the fan off\\nG28 Z0 ;move Z to bottom endstops\\nG28 X0 Y0 ;move X/Y to endstops\\nG1 X15 Y0 F4000 ;move X/Y to front of printer\\nG1 Z15.0 F9000 ;move the platform to 15mm\\nG92 E0 ;zero the extruded length\\nG1 F200 E50 ;extrude 10 mm of feed stock\\nG92 E0 ;zero the extruded length again\\nG1 F9000\\n;Put printing message on LCD screen\\nM117 Printing...\""
|
|
|
- },
|
|
|
- "machine_end_gcode" : {
|
|
|
- "value": "\";Version _2.6 of the firmware can abort the print too early if the file ends\\n;too soon. However if the file hasn't ended yet because there are comments at\\n;the end of the file, it won't abort yet. Therefore we have to put at least 512\\n;bytes at the end of the g-code so that the file is not yet finished by the\\n;time that the motion planner gets flushed. With firmware version _3.3 this\\n;should be fixed, so this comment wouldn't be necessary any more. Now we have\\n;to pad this text to make precisely 512 bytes.\" if machine_gcode_flavor == \"UltiGCode\" else \"M104 S0 ;extruder heater off\\nM140 S0 ;heated bed heater off (if you have it)\\nG91 ;relative positioning\\nG1 E-1 F300 ;retract the filament a bit before lifting the nozzle, to release some of the pressure\\nG1 Z+0.5 E-5 X-20 Y-20 F9000 ;move Z up a bit and retract filament even more\\nG28 X0 Y0 ;move X/Y to min endstops, so the head is out of the way\\nM84 ;steppers off\\nG90 ;absolute positioning\\n;Version _2.6 of the firmware can abort the print too early if the file ends\\n;too soon. However if the file hasn't ended yet because there are comments at\\n;the end of the file, it won't abort yet. Therefore we have to put at least 512\\n;bytes at the end of the g-code so that the file is not yet finished by the\\n;time that the motion planner gets flushed. With firmware version _3.3 this\\n;should be fixed, so this comment wouldn't be necessary any more. Now we have\\n;to pad this text to make precisely 512 bytes.\""
|
|
|
+ "machine_start_gcode": {
|
|
|
+ "default_value": "G21\nG90\nM82\nM107\nG28\nG1 Z15 F200\nT0\nG92 E0\nG1 E16 F250\nG92 E0\n"
|
|
|
},
|
|
|
+ "machine_end_gcode": {
|
|
|
+ "default_value": "G91\nG1 Z+0.5 E-16 Y+10 F9000\nG90\nM107\nM104 S0 T0\nM140 S0\nM117\nG28 X0 Y0\nM84"
|
|
|
+ },
|
|
|
+
|
|
|
"machine_width": {
|
|
|
"default_value": 220
|
|
|
},
|
|
|
@@ -39,15 +40,7 @@
|
|
|
"machine_heated_bed": {
|
|
|
"default_value": true
|
|
|
},
|
|
|
- "machine_head_with_fans_polygon":
|
|
|
- {
|
|
|
- "default_value": [
|
|
|
- [ -42, 12 ],
|
|
|
- [ -42, -32 ],
|
|
|
- [ 62, 12 ],
|
|
|
- [ 62, -32 ]
|
|
|
- ]
|
|
|
- },
|
|
|
+
|
|
|
"machine_center_is_zero": {
|
|
|
"default_value": false
|
|
|
},
|
|
|
@@ -60,13 +53,7 @@
|
|
|
"machine_gcode_flavor": {
|
|
|
"default_value": "Marlin"
|
|
|
},
|
|
|
- "machine_disallowed_areas": {
|
|
|
- "default_value": [
|
|
|
- [[-115, 112.5], [ -82, 112.5], [ -84, 102.5], [-115, 102.5]],
|
|
|
- [[ 115, 112.5], [ 115, 102.5], [ 110, 102.5], [ 108, 112.5]],
|
|
|
- [[-115, -112.5], [-115, -104.5], [ -84, -104.5], [ -82, -112.5]],
|
|
|
- [[ 115, -112.5], [ 108, -112.5], [ 110, -104.5], [ 115, -104.5]]
|
|
|
- ]},
|
|
|
+
|
|
|
"machine_nozzle_tip_outer_diameter": {
|
|
|
"default_value": 1
|
|
|
},
|
venkatkamesh