Change default_value to value

resources/definitions/Mark2_for_Ultimaker2.def.json

@@ -159,7 +159,7 @@
         "acceleration_wall": { "value": "math.ceil(acceleration_print * 1000 / 4000)" },
         "acceleration_wall_0": { "value": "math.ceil(acceleration_wall * 500 / 1000)" },
         "jerk_enabled": { "value": true },
-        "jerk_print": { "value": 12 },
+        "jerk_print": {"value": 12 },
         "jerk_travel":
         {
             "value": "jerk_print if magic_spiralize else 20"

resources/definitions/elegoo_neptune_2D.def.json

@@ -32,10 +32,10 @@
         "machine_extruders_share_nozzle": {"default_value": true},
         "machine_always_write_active_tool": {"default_value": true},
         "prime_blob_enable": {"default_value": false},
-    "prime_tower_enable": {"default_value": true},
-    "prime_tower_size": {"default_value": 30},
-    "prime_tower_min_volume": {"default_value": 90},
-    "speed_print": { "value": 60.0 },
+        "prime_tower_enable": {"default_value": true},
+        "prime_tower_size": {"default_value": 30},
+        "prime_tower_min_volume": {"default_value": 90},
+        "speed_print": { "value": 60.0 },
         "z_seam_type":{"default_value": "back"},
         "z_seam_corner":{"default_value": "z_seam_corner_weighted"},
         "material_standby_temperature":{"default_value": 200,"settable_per_extruder": false},
@@ -46,8 +46,8 @@
         "raft_margin":{"default_value": 5},
         "raft_airgap":{"default_value": 0.25},
         "brim_width":{"default_value": 5},
-    "skin_angles":{"default_value": [45, 135]},
-    "infill_pattern":{"default_value": "gyroid"},
+        "skin_angles":{"default_value": [45, 135]},
+        "infill_pattern":{"value": "gyroid"},
         "machine_gcode_flavor": {"default_value": "RepRap (Marlin/Sprinter)"},
         "machine_start_gcode": {"default_value": ";simage\n;gimage\nG28 ;home\n;G29 ;Run ABL\n;M420 S1 ;Enable ABL mesh\nG92 E0 ;Reset Extruder\nG1 Z4.0 F3000 ;Move Z Axis up\nG92 E0 ;Reset Extruder\nG1 X2.0 Y20 Z0.28 F5000.0 ;Move to start position\nG1 E90 F1200 ;Load filament\nG92 E0 ;Reset Extruder\nG1 X2.0 Y200.0 Z0.28 F1500.0 E15 ;Draw the first line\nG1 X2.3 Y200.0 Z0.28 F5000.0 ;Move to side a little\nG1 X2.3 Y20 Z0.28 F1500.0 E30 ;Draw the second line\nG92 E0 ;Reset Extruder\nG1 Z2.0 F3000 ;Move Z Axis up"},
         "machine_end_gcode": {"default_value": "G91 ;Relative positionning\nG1 E-2 F2700 ;Retract a bit\nG1 E-80 Z0.2 F1600 ;Retract and raise Z\nG1 X5 Y5 F3000 ;Wipe out\nG1 Z10 ;Raise Z more\nG90 ;Absolute positionning\nG1 X0 Y{machine_depth} ;Present print\nM106 S0 ;Turn-off fan\nM104 S0 ;Turn-off hotend\nM140 S0 ;Turn-off bed\nM84 X Y E ;Disable all steppers but Z"}