Apply version upgrade maximum deviation change to built-in profiles

For some this is not exactly restored as their original since this setting is limited to micron precision as well.

Contributes to issue CURA-7420.

resources/definitions/fdmprinter.def.json

@@ -5983,7 +5983,7 @@
                     "description": "The maximum deviation allowed when reducing the resolution for the Maximum Resolution setting. If you increase this, the print will be less accurate, but the g-code will be smaller. Maximum Deviation is a limit for Maximum Resolution, so if the two conflict the Maximum Deviation will always be held true.",
                     "type": "float",
                     "unit": "mm",
-                    "default_value": 0.05,
+                    "default_value": 0.025,
                     "minimum_value": "0.001",
                     "minimum_value_warning": "0.01",
                     "maximum_value_warning": "0.3",

resources/definitions/hms434.def.json

@@ -172,7 +172,7 @@
 
         "meshfix_maximum_resolution":       {"value": 0.01 },
         "meshfix_maximum_travel_resolution":{"value": 0.1 },
-        "meshfix_maximum_deviation":        {"value": 0.01 },
+        "meshfix_maximum_deviation":        {"value": 0.005 },
 
         "minimum_polygon_circumference":    {"value": 0.05 },
         "coasting_enable":                  {"value": false},

resources/definitions/peopoly_moai.def.json

@@ -171,7 +171,7 @@
             "value": "0.1"
         },
         "meshfix_maximum_deviation": {
-            "value": "0.003"
+            "value": "0.002"
         },
         "skin_outline_count": {
             "value": 0

resources/definitions/skriware_2.def.json

@@ -591,7 +591,7 @@
             "value": "0.2"
         },
         "meshfix_maximum_deviation": {
-            "default_value": 0.005
+            "default_value": 0.003
         },
         "jerk_roofing": {
             "value": "10"

resources/definitions/ultimaker_s3.def.json

@@ -155,7 +155,7 @@
         "wall_line_width_x": { "value": "round(line_width * 0.3 / 0.35, 2)" },
         "wall_thickness": { "value": "1" },
         "meshfix_maximum_resolution": { "value": "(speed_wall_0 + speed_wall_x) / 60" },
-        "meshfix_maximum_deviation": { "value": "layer_height / 2" },
+        "meshfix_maximum_deviation": { "value": "layer_height / 4" },
         "optimize_wall_printing_order": { "value": "True" },
         "retraction_combing": { "default_value": "all" },
         "initial_layer_line_width_factor": { "value": "120" },

resources/definitions/ultimaker_s5.def.json

@@ -157,7 +157,7 @@
         "wall_line_width_x": { "value": "round(line_width * 0.3 / 0.35, 2)" },
         "wall_thickness": { "value": "1" },
         "meshfix_maximum_resolution": { "value": "(speed_wall_0 + speed_wall_x) / 60" },
-        "meshfix_maximum_deviation": { "value": "layer_height / 2" },
+        "meshfix_maximum_deviation": { "value": "layer_height / 4" },
         "optimize_wall_printing_order": { "value": "True" },
         "retraction_combing": { "default_value": "all" },
         "initial_layer_line_width_factor": { "value": "120" },