Merge pull request #12532 from Ultimaker/PP-116_clean-up-DD-variant-profile

Pp 166 clean up dd variant profile

resources/variants/ultimaker_s3_dd04.inst.cfg

@@ -9,37 +9,8 @@ type = variant
 hardware_type = nozzle
 
 [values]
-brim_width = 7
 machine_nozzle_cool_down_speed = 0.9
 machine_nozzle_id = DD 0.4
 machine_nozzle_size = 0.4
-raft_acceleration = =acceleration_print
-raft_airgap = 0.3
-raft_base_thickness = =resolveOrValue('layer_height_0') * 1.2
-raft_interface_line_spacing = =raft_interface_line_width + 0.2
-raft_interface_line_width = =line_width * 2
-raft_interface_thickness = =layer_height * 1.5
-raft_jerk = =jerk_print
-raft_margin = 15
-raft_surface_layers = 2
-retraction_count_max = 25
-retraction_min_travel = =line_width * 2
+machine_nozzle_tip_outer_diameter = 1.2
 retraction_prime_speed = =retraction_speed
-speed_infill = =speed_print
-speed_layer_0 = 20
-speed_print = 45
-speed_support = =speed_topbottom
-speed_topbottom = =math.ceil(speed_print * 25 / 45)
-speed_travel_layer_0 = 50
-speed_wall = =math.ceil(speed_print * 30 / 45)
-speed_wall_0 = =math.ceil(speed_wall * 25 / 30)
-speed_wall_x = =speed_wall
-support_angle = 60
-support_bottom_distance = =support_z_distance / 2
-support_pattern = zigzag
-support_top_distance = =support_z_distance
-support_use_towers = True
-support_z_distance = =layer_height * 2
-switch_extruder_prime_speed = =switch_extruder_retraction_speeds
-switch_extruder_retraction_amount = =machine_heat_zone_length
-top_bottom_thickness = =layer_height * 6

resources/variants/ultimaker_s5_dd04.inst.cfg

@@ -9,37 +9,8 @@ type = variant
 hardware_type = nozzle
 
 [values]
-brim_width = 7
 machine_nozzle_cool_down_speed = 0.9
 machine_nozzle_id = DD 0.4
 machine_nozzle_size = 0.4
-raft_acceleration = =acceleration_print
-raft_airgap = 0.3
-raft_base_thickness = =resolveOrValue('layer_height_0') * 1.2
-raft_interface_line_spacing = =raft_interface_line_width + 0.2
-raft_interface_line_width = =line_width * 2
-raft_interface_thickness = =layer_height * 1.5
-raft_jerk = =jerk_print
-raft_margin = 15
-raft_surface_layers = 2
-retraction_count_max = 25
-retraction_min_travel = =line_width * 2
+machine_nozzle_tip_outer_diameter = 1.2
 retraction_prime_speed = =retraction_speed
-speed_infill = =speed_print
-speed_layer_0 = 20
-speed_print = 45
-speed_support = =speed_topbottom
-speed_topbottom = =math.ceil(speed_print * 25 / 45)
-speed_travel_layer_0 = 50
-speed_wall = =math.ceil(speed_print * 30 / 45)
-speed_wall_0 = =math.ceil(speed_wall * 25 / 30)
-speed_wall_x = =speed_wall
-support_angle = 60
-support_bottom_distance = =support_z_distance / 2
-support_pattern = zigzag
-support_top_distance = =support_z_distance
-support_use_towers = True
-support_z_distance = =layer_height * 2
-switch_extruder_prime_speed = =switch_extruder_retraction_speeds
-switch_extruder_retraction_amount = =machine_heat_zone_length
-top_bottom_thickness = =layer_height * 6