|
|
@@ -47,11 +47,11 @@
|
|
|
"adhesion_type": { "default_value": "skirt" },
|
|
|
"skirt_brim_minimal_length": { "default_value": 130},
|
|
|
|
|
|
- "machine_start_gcode": {
|
|
|
+ "machine_start_gcode": {
|
|
|
"default_value": "; FELIXprinters | www.FELIXprinters.com | Zeemanlaan 15 3401 MV IJsselstein The Netherlands\n; FELIX Tec 4 | Start Code Dual Extruders v1.0\n; Modified by kerog777@gmail.com\n;================================ \n;Initializing\nM80 ; Turn on the power supply\nM107 ; Turn off fans\nM117 Heating up\nM190 S{material_bed_temperature} ; Heatup Bed\nM104 T0 S120\nM104 T1 S120\nG28 ; Home all\nM109 T0 S{material_print_temperature_layer_0} ; Heatup hot-end\nM117 Purging\nT0 ; Select extruder 1\nG92 E0 ; Reset extruder\nG1 X10.0 Y1.1 Z5.0 F15240 ; Move to start-line position\nG1 Z0.3 F15240 ; Move z up\nG1 X127.0 Y1.1 Z0.3 F1500.0 E15 ; Purge 1st line\nG92 E0 ; Reset extruder\n\n;================================ ; Initializing done\nM117 FELIXprinting"
|
|
|
},
|
|
|
"machine_end_gcode": {
|
|
|
- "default_value": "; FELIXprinters End Code Tec Series v1.0\n; Modified by kerog777@gmail.com\n; ================================= \n; Move extruder to park position\nG91 ; Make coordinates relative\nG1 Z2 F1000 ; Move z 2mm up\nG90 ; Use absolute coordinates again\n G1 X0 Y0 F15240 ; Move bed and printhead to ergonomic position\n\n; ================================= ; Turn off heaters\nM140 S0 ; Turn off bed heater\nT0 ; Select left extruder\nM104 T0 S0 ; Turn off heater and continue\n G92 E0 ; Reset extruder position\nG1 E-6 ; Retract filament 8mm\nG92 E0 ; Reset extruder position\nT1 ; Select right extruder\nM104 T1 S0 ; Turn off heater and continue\nG92 E0 ; Reset extruder position\nG1 E-6 ; Retract filament 8mm\nG92 E0 ; Reset extruder position\nT0 ; Select left extruder\n\n; ================================= ; Turn the rest off\nM107 ; Turn off fan\nM84 ; Disable steppers\nM117 Finished Printing!"
|
|
|
+ "default_value": "; FELIXprinters End Code Tec Series v1.0\n; Modified by kerog777@gmail.com\n; ================================= \n; Move extruder to park position\nG91 ; Make coordinates relative\nG1 Z2 F1000 ; Move z 2mm up\nG90 ; Use absolute coordinates again\nG1 X0 Y0 F15240 ; Move bed and printhead to ergonomic position\n\n; ================================= ; Turn off heaters\nM140 S0 ; Turn off bed heater\nT0 ; Select left extruder\nM104 T0 S0 ; Turn off heater and continue\nG92 E0 ; Reset extruder position\nG1 E-6 ; Retract filament 8mm\nG92 E0 ; Reset extruder position\nT1 ; Select right extruder\nM104 T1 S0 ; Turn off heater and continue\nG92 E0 ; Reset extruder position\nG1 E-6 ; Retract filament 8mm\nG92 E0 ; Reset extruder position\nT0 ; Select left extruder\n\n; ================================= ; Turn the rest off\nM107 ; Turn off fan\nM84 ; Disable steppers\nM117 Finished Printing!"
|
|
|
}
|
|
|
}
|
|
|
}
|
Diego Prado Gesto